6I8651 SHOE-TRACK Caterpillar parts
1090, 325 L, 325 LN, 325B L, 325C, 325D, 325D L, 329D L, 329D LN, 329E LN, OEMS, TK711
Rating:
Alternative (cross code) number:
CA6I8651
6I-8651
6I8651
CA6I8651
6I-8651
6I8651
Weight: 73 pounds 33 kg.
Information:
BOLT HOLE SIZE
21
mm
BOLT HOLE SPACING A
25
mm
BOLT HOLE SPACING B
129
mm
BOLT HOLE SPACING C
72
mm
BOLT HOLE SPACING D
0
mm
PITCH
203
mm
WIDTH
900
mm
EXCAVATOR, UNDERCARRIAGE,
Compatible equipment models: 6I8651:
Number on catalog scheme:
2
For full view, you need register
Information:
Diagnostic Codes
Diagnostic codes alert the operator that a problem in the electronic system has been detected. Diagnostic codes are also used by the service technician to identify the nature of the problem. Caterpillar Electronic Technician (ET) is a software program that is for a personal computer. The software can be used by the service technician to view the diagnostic code information for an ECM. Diagnostic codes may consist of the module identifier (MID), the component identifier (CID), and the failure mode identifier (FMI).Component Identifier (MID) - The MID is a three-digit code that identifies the ECM that generated the diagnostic code. For example, the MID 036 identifies the engine ECM.Component Identifier (CID) - The CID is a number with three or four digits. The CID indicates the component that generated the code. For example, the CID number 0001 identifies the fuel injector for the number one cylinder.Failure Mode Identifier (FMI) - The FMI is a number that indicates the type of failure.Refer to Table 1 for a complete list of the diagnostic codes and the appropriate troubleshooting procedure.Note: Do not confuse diagnostic codes with event codes. Event codes alert the operator that an abnormal operating condition such as low oil pressure or high coolant temperature has been detected. If an event code is active, refer to Troubleshooting, "Event Codes".Illustration 1 is an example of the operating range of a sensor.
Illustration 1 g01365757
Example of the typical operating range of a sensor
(1) This area represents the normal operating range of the engine parameter.
(2) In these areas, the engine is operating in an unsafe operating range of the monitored parameter. An event code will be generated for the monitored parameter. The sensor circuit does not have an electronic problem. Refer to Troubleshooting, "Event Code List" for additional information on event codes.
(3) In these areas, the signal from the sensor is outside of the operating range of the sensor. The sensor circuit has an electronic problem. A diagnostic code will be generated for the sensor circuit.Active Diagnostic Codes
An active diagnostic code represents a problem with the electronic control system. Correct the problem as soon as possible.When the ECM generates an active diagnostic code, the "Active Alarm" indicator ("Engine Control Alarm Status" on Cat ET) is activated to alert the operator. If the condition that generated the code is momentary, the message disappears from the list of active diagnostic codes. The diagnostic code becomes logged.Logged Diagnostic Codes
When the ECM generates a diagnostic code, the ECM logs the code in permanent memory. The ECM has an internal diagnostic clock. Each ECM will record the following information when a code is generated:
The hour of the first occurrence of the code
The hour of the last occurrence of the code
The number of occurrences of the codeThis information is a valuable indicator for troubleshooting intermittent problems.A code is cleared from memory when one of the following conditions occur:
The service technician manually clears the code.
The code does not recur for 100 hours.
A new code is logged and there are already
Diagnostic codes alert the operator that a problem in the electronic system has been detected. Diagnostic codes are also used by the service technician to identify the nature of the problem. Caterpillar Electronic Technician (ET) is a software program that is for a personal computer. The software can be used by the service technician to view the diagnostic code information for an ECM. Diagnostic codes may consist of the module identifier (MID), the component identifier (CID), and the failure mode identifier (FMI).Component Identifier (MID) - The MID is a three-digit code that identifies the ECM that generated the diagnostic code. For example, the MID 036 identifies the engine ECM.Component Identifier (CID) - The CID is a number with three or four digits. The CID indicates the component that generated the code. For example, the CID number 0001 identifies the fuel injector for the number one cylinder.Failure Mode Identifier (FMI) - The FMI is a number that indicates the type of failure.Refer to Table 1 for a complete list of the diagnostic codes and the appropriate troubleshooting procedure.Note: Do not confuse diagnostic codes with event codes. Event codes alert the operator that an abnormal operating condition such as low oil pressure or high coolant temperature has been detected. If an event code is active, refer to Troubleshooting, "Event Codes".Illustration 1 is an example of the operating range of a sensor.
Illustration 1 g01365757
Example of the typical operating range of a sensor
(1) This area represents the normal operating range of the engine parameter.
(2) In these areas, the engine is operating in an unsafe operating range of the monitored parameter. An event code will be generated for the monitored parameter. The sensor circuit does not have an electronic problem. Refer to Troubleshooting, "Event Code List" for additional information on event codes.
(3) In these areas, the signal from the sensor is outside of the operating range of the sensor. The sensor circuit has an electronic problem. A diagnostic code will be generated for the sensor circuit.Active Diagnostic Codes
An active diagnostic code represents a problem with the electronic control system. Correct the problem as soon as possible.When the ECM generates an active diagnostic code, the "Active Alarm" indicator ("Engine Control Alarm Status" on Cat ET) is activated to alert the operator. If the condition that generated the code is momentary, the message disappears from the list of active diagnostic codes. The diagnostic code becomes logged.Logged Diagnostic Codes
When the ECM generates a diagnostic code, the ECM logs the code in permanent memory. The ECM has an internal diagnostic clock. Each ECM will record the following information when a code is generated:
The hour of the first occurrence of the code
The hour of the last occurrence of the code
The number of occurrences of the codeThis information is a valuable indicator for troubleshooting intermittent problems.A code is cleared from memory when one of the following conditions occur:
The service technician manually clears the code.
The code does not recur for 100 hours.
A new code is logged and there are already
Caterpillar parts catalog:
Parts shoe Caterpillar catalog:
1140, 1150, 1160, 120G, 120M, 12E, 12G, 12H, 12H ES, 12H NA, 12M, 130G, 140G, 140H, 140H ES, 140H NA, 140M, 143H, 14E, 14G, 14H, 14H NA, 14M, 160G, 160H, 160H ES, 160H NA, 160M, 163H, 163H NA, 1673, 1...
1090, 1190, 1190T, 120M, 120M 2, 1290T, 12M 2, 12M 3, 12M 3 AWD, 1390, 140M, 140M 2, 140M 3, 140M 3 AWD, 14H, 14M, 16, 160M, 160M 2, 160M 3, 160M 3 AWD, 1693, 16H NA, 16M, 2290, 235, 235D, 2390, 2391,...
315, 315B, 315B FM L, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320B, 320B FM LL, 320B U, 320C, 320C FM, 320D, 320D GC, 320D L, 320D...
315, 315B L, 315C, 315D L, 317, 317B LN, 318B, 318C, 318E L, 319D L, 319D LN, 320, 320 L, 320B, 320B FM LL, 320B U, 320C, 320C FM, 320D, 320D FM, 320D L, 320D LRR, 320D RR, 320D2, 320D2 L, 320E, 320E ...
311, 311B, 315B L, 317, 317B LN, 318B, 318C, 319D, 320, 320 L, 320B, 320B FM LL, 320B L, 320B U, 320C, 320C FM, 320C L, 320D, 320D L, 320D LRR, 320D RR, 320N, 321B, 321C, 321D LCR, 322, 322 FM L, 322 ...
312D, 325C, 328D LCR, 330, 330 FM L, 330B, 330B L, 330C, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336E, 336E H, 336E L, 336E LH, 336E LN, OEMS
322 FM L, 322B L, 322C, 325, 325 L, 325 LN, 325B, 325B L, 325C, 325D, 325D L, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 336D L, 345C, OEMS
322C, 325, 325 L, 325 LN, 325B, 325B L, 325C, 325C L, 325D, 325D L, 325D MH, 329D, 329D L, 329D LN, 329E, 329E LN, OEMS
325C, 328D LCR, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C L, 330C MH, 330D L, 336D, 336D L, 336E L, 336E LH, 336E LN, 336F L, OEMS
325C, 330, 330 FM L, 330B, 330B L, 330C, 330C L, 330C MH, OEMS
1210137
SHOE-TRACK
325 L, 325B L, 325C, 325D, 325D L, 329D, 329D L, 329D LN, 329E LN
325 L, 325B L, 325C, 325D, 325D L, 329D, 329D L, 329D LN, 329E LN
6Y5662
SHOE-TRACK
325, 325 L, 325 LN
325, 325 L, 325 LN
3Q6993
SHOE-TRACK
1090, 2290, 324D FM, 324D FM LL, 511, OEMS, TK711
1090, 2290, 324D FM, 324D FM LL, 511, OEMS, TK711
1528628
SHOE-TRACK
1090, 2290, 322C FM, 324D FM, 324D FM LL, 511, TK711
1090, 2290, 322C FM, 324D FM, 324D FM LL, 511, TK711
6I9854
SHOE-TRACK
1090, 2290, 325, 325 L, 511, OEMS, TK711
1090, 2290, 325, 325 L, 511, OEMS, TK711
2247733
SHOE-TRACK MASTER
320C FM, 320D, 320D FM, 320D FM RR
320C FM, 320D, 320D FM, 320D FM RR
2247270
SHOE-TRACK
320C FM, 320D, 320D FM, 320D FM RR
320C FM, 320D, 320D FM, 320D FM RR
2247732
SHOE-TRACK MASTER
1090, 320C FM, 320D, 320D FM, 320D FM RR, TK711
1090, 320C FM, 320D, 320D FM, 320D FM RR, TK711
2177683
SHOE-TRACK
345C
345C
3452210
SHOE-TRACK
320E L, 320E LRR, 324D, 324E, 324E L, 324E LN
320E L, 320E LRR, 324D, 324E, 324E L, 324E LN
2588328
SHOE-TRACK
TK751, TK752
TK751, TK752
2530336
SHOE-TRACK
551, 552, 552 2, TK751, TK752
551, 552, 552 2, TK751, TK752
2878270
SHOE-TRACK
1190, 1190T, 2390, 2391, 521, 522
1190, 1190T, 2390, 2391, 521, 522
2878269
SHOE-TRACK
1190, 1190T, 2390, 2391, 521, 522
1190, 1190T, 2390, 2391, 521, 522