6Y1385 SHOE-TRACK Caterpillar parts
D3B, D3C, D3C II, D3C III, D4C, D4C II, D4C III
Rating:
Alternative (cross code) number:
CA6Y1385
6Y-1385
6Y1385
CA6Y1385
6Y-1385
6Y1385
Weight: 21 pounds 9 kg.
Information:
BOLT HOLE SIZE
14.96
mm
BOLT HOLE SPACING A
7.92
mm
BOLT HOLE SPACING B
88.92
mm
BOLT HOLE SPACING C
54.86
mm
BOLT HOLE SPACING D
28
mm
PITCH
155.5
mm
WIDTH
635
mm
TRACK-TYPE TRACTOR,
Compatible equipment models: 6Y1385:
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 7649 Primer N -
B - Loctite 620 Retaining Compound -
C 147-2675 Wear Sleeve Installer 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01140085
Illustration 2 g03698745
Numerical tightening sequence for bolts (2).
Note: If required, install a crankshaft wear sleeve at engine overhaul. For more information please refer to the following Reuse and Salvage Guidelines. Refer to Reuse and Salvage Guidelines, SEBF9217, "Specifications for Crankshafts C7, C9, C-9, C10, C11, C12, C-12, C13, C-13, C15, C-15, C18, C-18, C27, C30, and C32 Engines" or the correct specifications of the crankshaft. Refer to Reuse and Salvage Guidelines, SEBF8039, "Crankshaft Visual Inspection and Magnetic Particle Inspection" for the correct inspection procedure of the crankshaft seal surface.
If a crankshaft wear sleeve is necessary, refer to Step 1.a through Step 1.d to install the crankshaft wear sleeve. If a crankshaft wear sleeve is not necessary, refer to Step 2.
Clean and polish the crankshaft of imperfections.
Use Tooling (A) to clean the outside diameter of the crankshaft and the inside diameter of the crankshaft wear sleeve.
Apply Tooling (B) to the outside diameter of the crankshaft and the inside diameter of the crankshaft wear sleeve.
Use Tooling (C) to install the crankshaft wear sleeve. Note: Leave the shipping sleeve in place to install the crankshaft rear seal. The crankshaft rear seal must be installed dry.Note: If the seal group, O-ring seal, and the shipping sleeve are separated, these components should not be used.
Lubricate the O-ring seal with clean engine oil that is on the back of the crankshaft rear seal (1).
Position crankshaft rear seal (1) and the shipping sleeve over the crankshaft. Push crankshaft rear seal (1) in place. This will dislodge the shipping sleeve. Note: Do not remove the shipping sleeve until bolts (2) are installed.
Install new bolts (2) hand tight. Then, tighten bolts (2) in numerical sequence, shown in Illustration 2. Tighten bolts (2) to a torque of 12 3 N m (106 27 lb in). End By:
Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Loctite 7649 Primer N -
B - Loctite 620 Retaining Compound -
C 147-2675 Wear Sleeve Installer 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01140085
Illustration 2 g03698745
Numerical tightening sequence for bolts (2).
Note: If required, install a crankshaft wear sleeve at engine overhaul. For more information please refer to the following Reuse and Salvage Guidelines. Refer to Reuse and Salvage Guidelines, SEBF9217, "Specifications for Crankshafts C7, C9, C-9, C10, C11, C12, C-12, C13, C-13, C15, C-15, C18, C-18, C27, C30, and C32 Engines" or the correct specifications of the crankshaft. Refer to Reuse and Salvage Guidelines, SEBF8039, "Crankshaft Visual Inspection and Magnetic Particle Inspection" for the correct inspection procedure of the crankshaft seal surface.
If a crankshaft wear sleeve is necessary, refer to Step 1.a through Step 1.d to install the crankshaft wear sleeve. If a crankshaft wear sleeve is not necessary, refer to Step 2.
Clean and polish the crankshaft of imperfections.
Use Tooling (A) to clean the outside diameter of the crankshaft and the inside diameter of the crankshaft wear sleeve.
Apply Tooling (B) to the outside diameter of the crankshaft and the inside diameter of the crankshaft wear sleeve.
Use Tooling (C) to install the crankshaft wear sleeve. Note: Leave the shipping sleeve in place to install the crankshaft rear seal. The crankshaft rear seal must be installed dry.Note: If the seal group, O-ring seal, and the shipping sleeve are separated, these components should not be used.
Lubricate the O-ring seal with clean engine oil that is on the back of the crankshaft rear seal (1).
Position crankshaft rear seal (1) and the shipping sleeve over the crankshaft. Push crankshaft rear seal (1) in place. This will dislodge the shipping sleeve. Note: Do not remove the shipping sleeve until bolts (2) are installed.
Install new bolts (2) hand tight. Then, tighten bolts (2) in numerical sequence, shown in Illustration 2. Tighten bolts (2) to a torque of 12 3 N m (106 27 lb in). End By:
Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Caterpillar parts catalog:
Parts shoe Caterpillar catalog:
6Y1597
SHOE-TRACK (MASTER)
931B, 931C, 931C II, 933, 933C, 935B, 935C, 935C II, D3C III, D3G, D3K XL, D3K2 LGP, D4C III, PR-450C
931B, 931C, 931C II, 933, 933C, 935B, 935C, 935C II, D3C III, D3G, D3K XL, D3K2 LGP, D4C III, PR-450C
6Y1596
SHOE-TRACK
931B, 931C, 931C II, 933, 933C, 935B, 935C, 935C II, D3C III, D3G, D3K XL, D3K2 LGP, D4C III, PR-450C
931B, 931C, 931C II, 933, 933C, 935B, 935C, 935C II, D3C III, D3G, D3K XL, D3K2 LGP, D4C III, PR-450C
6T2779
SHOE-TRACK
D3B, D3C, D3C II
D3B, D3C, D3C II
6T2780
SHOE-TRACK
D3B, D3C, D3C II
D3B, D3C, D3C II
2352558
SHOE-TRACK
D3C III, D3G, D3K XL, D3K2 LGP, D4C III, D4G, D4K XL, D4K2 XL
D3C III, D3G, D3K XL, D3K2 LGP, D4C III, D4G, D4K XL, D4K2 XL
2352559
SHOE-TRACK
D3C III, D3G, D3K XL, D3K2 LGP, D4C III, D4G
D3C III, D3G, D3K XL, D3K2 LGP, D4C III, D4G
6Y5344
SHOE-TRACK
D4C III
D4C III
6Y5345
SHOE-TRACK MASTER
D4C III
D4C III
2432693
SHOE-TRACK
D4C III, D4G, D4K XL, D4K2 XL
D4C III, D4G, D4K XL, D4K2 XL
2465475
SHOE-TRACK
D4C III, D4G
D4C III, D4G
2633798
SHOE-TRACK MASTER
D3G, D3K XL, D3K2 LGP, D4C III, D4G, D4K XL, D4K2 XL
D3G, D3K XL, D3K2 LGP, D4C III, D4G, D4K XL, D4K2 XL
2606750
SHOE-TRACK
D3G, D4C III, D4G
D3G, D4C III, D4G
6S8824
SHOE
931B, D3, D3B, D4B
931B, D3, D3B, D4B
6S9059
SHOE-MASTER
931B, D3, D3B, D4B
931B, D3, D3B, D4B
3T0360
SHOE-TRACK
561H, D4H, D5C, D5C III, D5G
561H, D4H, D5C, D5C III, D5G
8E9812
SHOE-TRACK
561H, 561M, D4H XL, D5C, D5C III, D5G, D5K LGP, D5K2 XL, D5M, D5N
561H, 561M, D4H XL, D5C, D5C III, D5G, D5K LGP, D5K2 XL, D5M, D5N
2465213
SHOE-TRACK
D6R II, D6R III, D6T, D6T LGP, D6T XL
D6R II, D6R III, D6T, D6T LGP, D6T XL
2731686
SHOE-TRACK
D6R II
D6R II
6S8814
SHOE
D3, D3B
D3, D3B
6S9063
SHOE-MASTER
931B, D3B
931B, D3B
6S8822
SHOE
935B, D3, D3B
935B, D3, D3B
6S9115
SHOE-LGP
931, 931B, 931C, 931C II, 933, 933C, D3, D3B, D3C, D3C II, D3C III, D3G, D3K XL, D3K2 LGP, D4B, D4C, D4C II, D4C III, D4G, D4K XL, D4K2 XL
931, 931B, 931C, 931C II, 933, 933C, D3, D3B, D3C, D3C II, D3C III, D3G, D3K XL, D3K2 LGP, D4B, D4C, D4C II, D4C III, D4G, D4K XL, D4K2 XL
6S9102
SHOE-LGP MASTER
931, 931B, 931C, 931C II, 933, 933C, D3, D3B, D3C, D3C II, D3C III, D3G, D3K XL, D3K2 LGP, D4B, D4C, D4C II, D4C III, D4G, D4K XL, D4K2 XL
931, 931B, 931C, 931C II, 933, 933C, D3, D3B, D3C, D3C II, D3C III, D3G, D3K XL, D3K2 LGP, D4B, D4C, D4C II, D4C III, D4G, D4K XL, D4K2 XL
6Y1386
SHOE-TRACK MASTER
D3B, D3C, D3C II, D3C III, D4C, D4C II, D4C III
D3B, D3C, D3C II, D3C III, D4C, D4C II, D4C III