6Y2756 SHOE-TRACK Caterpillar parts
330, 330 L, OEMS
Rating:
Alternative (cross code) number:
CA6Y2756
6Y-2756
6Y2756
CA6Y2756
6Y-2756
6Y2756
Weight: 56 pounds 25 kg.
EXCAVATOR, UNDERCARRIAGE,
Number on catalog scheme:
2
For full view, you need register
Information:
Implement ECM
This test is reserved for identifying conditions related to the programming of the ECM or a signal failure. In this instance the ECM is receiving information that is erratic, intermittent, or incorrect. A failure of the internal program of the ECM is associated with the test as well. The fault messages displayed in Cat ET or via the Information Display include "programmed parameter fault" or some type of machine monitoring failure.The following diagnostic trouble codes (DTC) are associated with the configuration parameters for the Implement ECM.
Table 1
Implement ECM (MID 82)
DTC Description System Response
268-2 Programmed Parameter Fault: Data Erratic, Intermittent, or Incorrect The Implement ECM has determined that a configuration parameter is not programmed. The ECM will display the parameter causing the problem via Cat® ET. Possible causes of an FMI 2 diagnostic code are:
The sales model and product identification need programming.
The ECM is incorrect.Diagnostic Trouble Code Procedure
Note: Prior to beginning this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure and in good condition. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure.
Table 2
Troubleshooting Test Steps Values Results
1. Verify The Configuration Of The Sales Model.
A. Use the Cat ® Electronic Technician (Cat ET) to verify that the ECM is configured to the default setting configuration.
The ECM has been configured correctly to the default setting configuration. OK: The ECM has been configured correctly to the default setting configuration.
Verify that the new configuration has corrected the problem before attempting to operate the machine.
STOP
NOT OK: The ECM does not have the appropriate sales model and product identification.
Proceed to Test Step 2.
2. Configure The ECM.
A. Use Cat ET to reset the configuration to the default setting configuration. Reset the installation status to the correct type for the attachments that are installed on the machine.
The ECM is configured to the default setting configuration. OK: The ECM is configured to the default setting configuration.
Verify that the new configuration has corrected the problem before attempting to operate the machine.
STOP
NOT OK: The ECM is not configured to the default setting configuration.
Repair: Repeat this procedure.
If the diagnostic code remains active or repeatedly activated and no cause can be found, flash the ECM with the latest version of software. Ensure that you have the latest version of software for your specific machine and ECM. Refer to the Troubleshooting, " ECM Software - Install " section of this manual for the correct procedure.
If the problem is still present after flashing the latest software to the ECM, contact the Technical Communicator at your dealership for a possible consultation with Caterpillar.
STOP
This test is reserved for identifying conditions related to the programming of the ECM or a signal failure. In this instance the ECM is receiving information that is erratic, intermittent, or incorrect. A failure of the internal program of the ECM is associated with the test as well. The fault messages displayed in Cat ET or via the Information Display include "programmed parameter fault" or some type of machine monitoring failure.The following diagnostic trouble codes (DTC) are associated with the configuration parameters for the Implement ECM.
Table 1
Implement ECM (MID 82)
DTC Description System Response
268-2 Programmed Parameter Fault: Data Erratic, Intermittent, or Incorrect The Implement ECM has determined that a configuration parameter is not programmed. The ECM will display the parameter causing the problem via Cat® ET. Possible causes of an FMI 2 diagnostic code are:
The sales model and product identification need programming.
The ECM is incorrect.Diagnostic Trouble Code Procedure
Note: Prior to beginning this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, secure and in good condition. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure.
Table 2
Troubleshooting Test Steps Values Results
1. Verify The Configuration Of The Sales Model.
A. Use the Cat ® Electronic Technician (Cat ET) to verify that the ECM is configured to the default setting configuration.
The ECM has been configured correctly to the default setting configuration. OK: The ECM has been configured correctly to the default setting configuration.
Verify that the new configuration has corrected the problem before attempting to operate the machine.
STOP
NOT OK: The ECM does not have the appropriate sales model and product identification.
Proceed to Test Step 2.
2. Configure The ECM.
A. Use Cat ET to reset the configuration to the default setting configuration. Reset the installation status to the correct type for the attachments that are installed on the machine.
The ECM is configured to the default setting configuration. OK: The ECM is configured to the default setting configuration.
Verify that the new configuration has corrected the problem before attempting to operate the machine.
STOP
NOT OK: The ECM is not configured to the default setting configuration.
Repair: Repeat this procedure.
If the diagnostic code remains active or repeatedly activated and no cause can be found, flash the ECM with the latest version of software. Ensure that you have the latest version of software for your specific machine and ECM. Refer to the Troubleshooting, " ECM Software - Install " section of this manual for the correct procedure.
If the problem is still present after flashing the latest software to the ECM, contact the Technical Communicator at your dealership for a possible consultation with Caterpillar.
STOP
Caterpillar parts catalog:
Parts shoe Caterpillar catalog:
1140, 1150, 1160, 120G, 120M, 12E, 12G, 12H, 12H ES, 12H NA, 12M, 130G, 140G, 140H, 140H ES, 140H NA, 140M, 143H, 14E, 14G, 14H, 14H NA, 14M, 160G, 160H, 160H ES, 160H NA, 160M, 163H, 163H NA, 1673, 1...
1090, 1190, 1190T, 120M, 120M 2, 1290T, 12M 2, 12M 3, 12M 3 AWD, 1390, 140M, 140M 2, 140M 3, 140M 3 AWD, 14H, 14M, 16, 160M, 160M 2, 160M 3, 160M 3 AWD, 1693, 16H NA, 16M, 2290, 235, 235D, 2390, 2391,...
315, 315B, 315B FM L, 315B L, 315C, 315D L, 316E L, 317, 317B LN, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320B, 320B FM LL, 320B U, 320C, 320C FM, 320D, 320D GC, 320D L, 320D...
315, 315B L, 315C, 315D L, 317, 317B LN, 318B, 318C, 318E L, 319D L, 319D LN, 320, 320 L, 320B, 320B FM LL, 320B U, 320C, 320C FM, 320D, 320D FM, 320D L, 320D LRR, 320D RR, 320D2, 320D2 L, 320E, 320E ...
311, 311B, 315B L, 317, 317B LN, 318B, 318C, 319D, 320, 320 L, 320B, 320B FM LL, 320B L, 320B U, 320C, 320C FM, 320C L, 320D, 320D L, 320D LRR, 320D RR, 320N, 321B, 321C, 321D LCR, 322, 322 FM L, 322 ...
312D, 325C, 328D LCR, 330, 330 FM L, 330B, 330B L, 330C, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336E, 336E H, 336E L, 336E LH, 336E LN, OEMS
322 FM L, 322B L, 322C, 325, 325 L, 325 LN, 325B, 325B L, 325C, 325D, 325D L, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 336D L, 345C, OEMS
322C, 325, 325 L, 325 LN, 325B, 325B L, 325C, 325C L, 325D, 325D L, 325D MH, 329D, 329D L, 329D LN, 329E, 329E LN, OEMS
325C, 328D LCR, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C L, 330C MH, 330D L, 336D, 336D L, 336E L, 336E LH, 336E LN, 336F L, OEMS
325C, 330, 330 FM L, 330B, 330B L, 330C, 330C L, 330C MH, OEMS
1210140
SHOE-TRACK
328D LCR, 330 FM L, 330 L, 330B L, 330C, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336E HVG, 336E L, 336E LH, 336E LN
328D LCR, 330 FM L, 330 L, 330B L, 330C, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336E HVG, 336E L, 336E LH, 336E LN
328D LCR, 330 FM L, 330 L, 330B L, 330C, 330C L, 330D L, 330D LN, 330D MH, 336D L
1Q4752
SHOE-TRACK
OEMS
OEMS
1265065
SHOE-TRACK
325, 325 L, 325B L, 325C, 325C FM, 325D L, 329D, 329D L, 329E, OEMS
325, 325 L, 325B L, 325C, 325C FM, 325D L, 329D, 329D L, 329E, OEMS
325 L, 325 LN, OEMS
6I9893
SHOE-TRACK
330, 330 FM L, OEMS
330, 330 FM L, OEMS
8E4501
SHOE-TRACK
OEMS
OEMS
2086044
SHOE-TRACK
OEMS
OEMS
1504767
SHOE-TRACK
330D L, 345B, 345B II, 345B L, 345C, 345C L, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, OEMS
330D L, 345B, 345B II, 345B L, 345C, 345C L, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L VG, 349F L, OEMS
1834634
SHOE-TRACK
OEMS
OEMS
1686983
SHOE-TRACK
OEMS
OEMS
9Q5601
SHOE-TRACK
OEMS
OEMS