8E4497 SHOE-TRACK MASTER Caterpillar parts
963, 963B, 963C, 963D
Rating:
Alternative (cross code) number:
CA8E4497
8E-4497
8E4497
CA8E4497
8E-4497
8E4497
Weight: 45 pounds 20 kg.
Information:
BOLT HOLE SIZE
20.37
mm
BOLT HOLE SPACING A
11.94
mm
BOLT HOLE SPACING B
134.85
mm
BOLT HOLE SPACING C
44.45
mm
BOLT HOLE SPACING D
56.39
mm
PITCH
203
mm
WIDTH
550
mm
TRACK LOADER,
Information:
Test Procedure
System Operation
The SLC 5/04 indicators are located on the front of the following components: Power Supply, CPU and I/O Modules.The diagnostic indicators help trace the source of the fault. Faults can be found in the following components: input devices, output devices, wiring and the controller.The battery is a replaceable lithium battery. The battery provides backup power for approximately two years. The "BATT" LED on the front of the processor alerts you when the battery voltage has fallen below a threshold level.The red "FLT" LED is flashing during operation. The processor detects a major fault. The fault is in the processor expansion chassis or the fault is in the memory.The red "BATT" LED is illuminated. The battery voltage has fallen below a threshold level.The red "BATT" LED is not illuminated. The battery is functional.
Illustration 1 g00766233
Diagram of LED indicators
Illustration 2 g00563548
Functional Test
Check the electrical connectors and check the wiring.
Bodily contact with electrical potential can cause bodily injury or death.To avoid the possibility of injury or death, ensure that the main power supply has been disconnected before performing any maintenance or removing any modules.
Disconnect the power supply.
Check the electrical connectors and check the wiring for damage or bad connections.
Verify that all modules are properly seated.
Verify the status of the LED on the SLC 5/04.The results of the preceding procedure are in the following list:
All of the components are fully installed. All of the components are free of corrosion. All of the components are free of damage. All of the modules are properly seated. Proceed to 2.
The components are not fully installed. The components are not free of corrosion. The components are damaged. All of the modules are not properly seated. Repair the component. Verify that the repair resolves the problem. STOP.
Verify that the battery is connected.
Verify that the battery is properly connected.The results of the preceding procedure are in the following list:
The battery is properly connected. Replace the battery. Verify that the repair resolves the problem. Refer to Maintenance Procedure, "Battery - Replace". Stop.
The battery is not properly connected. Proceed to 3.
Replace the battery.
To avoid damage to electronic components, do not remove the processor from the SLC 5/04 Chassis until all power is removed from the power supply.Do not expose memory modules to surfaces or areas that may typically hold an electrostatic charge.
Secure power to the processor.
Press the retaining clips at the top of the processor and press the retaining clips at the bottom of the processor.
Remove the processor from the chassis.
To avoid potential damage to the processor, handle all modules by the ends of the carrier or edges of the plastic housing. Skin oil or dirt can corrode metallic surfaces, inhibiting electrical contact.
Disconnect the battery. Remove the battery.
Install the new battery. Connect the new battery.
Align the processor and the guides in the chassis.
Gently slide the processor in the chassis. Secure the top retainer clips and secure the bottom retainer clips.
Install a wire tie in order to secure the wiring.The results of the preceding procedure are in the following list:
No errors
System Operation
The SLC 5/04 indicators are located on the front of the following components: Power Supply, CPU and I/O Modules.The diagnostic indicators help trace the source of the fault. Faults can be found in the following components: input devices, output devices, wiring and the controller.The battery is a replaceable lithium battery. The battery provides backup power for approximately two years. The "BATT" LED on the front of the processor alerts you when the battery voltage has fallen below a threshold level.The red "FLT" LED is flashing during operation. The processor detects a major fault. The fault is in the processor expansion chassis or the fault is in the memory.The red "BATT" LED is illuminated. The battery voltage has fallen below a threshold level.The red "BATT" LED is not illuminated. The battery is functional.
Illustration 1 g00766233
Diagram of LED indicators
Illustration 2 g00563548
Functional Test
Check the electrical connectors and check the wiring.
Bodily contact with electrical potential can cause bodily injury or death.To avoid the possibility of injury or death, ensure that the main power supply has been disconnected before performing any maintenance or removing any modules.
Disconnect the power supply.
Check the electrical connectors and check the wiring for damage or bad connections.
Verify that all modules are properly seated.
Verify the status of the LED on the SLC 5/04.The results of the preceding procedure are in the following list:
All of the components are fully installed. All of the components are free of corrosion. All of the components are free of damage. All of the modules are properly seated. Proceed to 2.
The components are not fully installed. The components are not free of corrosion. The components are damaged. All of the modules are not properly seated. Repair the component. Verify that the repair resolves the problem. STOP.
Verify that the battery is connected.
Verify that the battery is properly connected.The results of the preceding procedure are in the following list:
The battery is properly connected. Replace the battery. Verify that the repair resolves the problem. Refer to Maintenance Procedure, "Battery - Replace". Stop.
The battery is not properly connected. Proceed to 3.
Replace the battery.
To avoid damage to electronic components, do not remove the processor from the SLC 5/04 Chassis until all power is removed from the power supply.Do not expose memory modules to surfaces or areas that may typically hold an electrostatic charge.
Secure power to the processor.
Press the retaining clips at the top of the processor and press the retaining clips at the bottom of the processor.
Remove the processor from the chassis.
To avoid potential damage to the processor, handle all modules by the ends of the carrier or edges of the plastic housing. Skin oil or dirt can corrode metallic surfaces, inhibiting electrical contact.
Disconnect the battery. Remove the battery.
Install the new battery. Connect the new battery.
Align the processor and the guides in the chassis.
Gently slide the processor in the chassis. Secure the top retainer clips and secure the bottom retainer clips.
Install a wire tie in order to secure the wiring.The results of the preceding procedure are in the following list:
No errors
Caterpillar parts catalog:
Parts shoe Caterpillar catalog:
8H1141
SHOE-POLE
1140, 1150, 1160, 120G, 120M, 12E, 12G, 12H, 12H ES, 12H NA, 12M, 130G, 140G, 140H, 140H ES, 140H NA, 140M, 143H, 14E, 14G, 14H, 14H NA, 14M, 160G, 160H, 160H ES, 160H NA, 160M, 163H, 163H NA, 1673, 1...
1140, 1150, 1160, 120G, 120M, 12E, 12G, 12H, 12H ES, 12H NA, 12M, 130G, 140G, 140H, 140H ES, 140H NA, 140M, 143H, 14E, 14G, 14H, 14H NA, 14M, 160G, 160H, 160H ES, 160H NA, 160M, 163H, 163H NA, 1673, 1...
2313713
SHOE-TRACK
963B, 963C, 963D
963B, 963C, 963D
2564971
SHOE-TRACK MASTER
963B, 963C, 963D
963B, 963C, 963D
1Q4610
SHOE-TRACK
963C
963C
1Q4640
SHOE-TRACK
963C, 963D
963C, 963D
1Q4641
SHOE-TRACK MASTER
963C, 963D
963C, 963D
1906079
SHOE-TRACK
963C
963C
1277009
SHOE-TRACK
963C
963C
2854296
SHOE-TRACK
963C, 963D
963C, 963D
2838702
SHOE-TRACK
963D, D6R III, D6T, D6T LGP, D6T LGPPAT, D6T XL
963D, D6R III, D6T, D6T LGP, D6T LGPPAT, D6T XL
2926381
SHOE-TRACK
963D
963D
8E4496
SHOE-TRACK
963, 963B, 963C, 963D
963, 963B, 963C, 963D
8E6977
SHOE-TRACK
963, 963B, 963C
963, 963B, 963C
8E6978
SHOE-MASTER TRACK
963, 963B, 963C
963, 963B, 963C
8E4495
SHOE-TRACK MASTER
963, 963B, 963C, 963D
963, 963B, 963C, 963D
8E4494
SHOE-TRACK
963, 963B, 963C, 963D
963, 963B, 963C, 963D
7P2491
SHOE
963
963
7P2493
SHOE
963
963