1386551 SHROUD Caterpillar parts
324D, 324D L, 325D L, 330D L, 336D, 336D L, 336D2, 336D2 L, 336E L, 345C, 345D L, 349D L, 349E L, 349E L VG, 365B II, 365C, 374D L, 374F L, 988K, 990H, 990K, 992G
Rating:
Alternative (cross code) number:
CA1386551
138-6551
1386551
CA1386551
138-6551
1386551
Weight: 28 pounds 12 kg.
EXCAVATOR, WHEEL LOADER,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 1386551 Shroud-Heel, Curved
CTP Curved || Sold in each || Easy in-and-out fit
CTP Curved || Sold in each || Easy in-and-out fit
CTP 1386551 Shroud-Heel, Curved
CTP Curved || Sold in each || Easy in-and-out fit
CTP Curved || Sold in each || Easy in-and-out fit
Number on catalog scheme:
11
For full view, you need register
Compatible equipment models: 1386551:
Information:
Removal Procedure
Table 1
Required Tools
Tools Part Number Part Description Qty
A 8T-0914 Flywheel Guide Pin 2
B 138-7573 Link Bracket 2 Start By:
Remove the damper guard group. Note: This removal procedure is for vibration dampers that have an accessory module in position.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: If the accessory module is in the way and overhead lifting can not be done, the following procedure can be used to remove the vibration dampers. The configuration of the engine must allow the vibration damper to be removed from the front of the engine.
Illustration 1 g00610080
Use a 2250 kg (5000 lb) lift truck with a boom extension. Be sure that the boom extension is properly anchored to the lift truck.
Use the sleeve (1) to pilot the removal of the vibration damper.
Illustration 2 g00610082
This is an Illustration of a single vibration damper.
Remove two of the bolts that hold the vibration damper (2) in position and install Tool (A).
Use the lift truck and move the sleeve (1) into position in the center of the vibration damper.
Remove the remaining bolts that hold the vibration damper in place.
Install Tool (B) on the vibration damper. Fasten a chain from the lift truck to Tool (B) in order to hold the vibration damper and the sleeve (1) on the lift truck boom.
Carefully move the vibration damper off the guide pins. Carefully maneuver the vibration damper in order to move the damper away from the accessory module.
Illustration 3 g00610083
Remove the vibration damper (2) from the lift truck. The weight of a narrow vibration damper is approximately 288 kg (639 lb). The weight of a wide vibration damper is approximately 402 kg (882 lb).
Remove the spacer from the front of the crankshaft.
Table 1
Required Tools
Tools Part Number Part Description Qty
A 8T-0914 Flywheel Guide Pin 2
B 138-7573 Link Bracket 2 Start By:
Remove the damper guard group. Note: This removal procedure is for vibration dampers that have an accessory module in position.
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Note: If the accessory module is in the way and overhead lifting can not be done, the following procedure can be used to remove the vibration dampers. The configuration of the engine must allow the vibration damper to be removed from the front of the engine.
Illustration 1 g00610080
Use a 2250 kg (5000 lb) lift truck with a boom extension. Be sure that the boom extension is properly anchored to the lift truck.
Use the sleeve (1) to pilot the removal of the vibration damper.
Illustration 2 g00610082
This is an Illustration of a single vibration damper.
Remove two of the bolts that hold the vibration damper (2) in position and install Tool (A).
Use the lift truck and move the sleeve (1) into position in the center of the vibration damper.
Remove the remaining bolts that hold the vibration damper in place.
Install Tool (B) on the vibration damper. Fasten a chain from the lift truck to Tool (B) in order to hold the vibration damper and the sleeve (1) on the lift truck boom.
Carefully move the vibration damper off the guide pins. Carefully maneuver the vibration damper in order to move the damper away from the accessory module.
Illustration 3 g00610083
Remove the vibration damper (2) from the lift truck. The weight of a narrow vibration damper is approximately 288 kg (639 lb). The weight of a wide vibration damper is approximately 402 kg (882 lb).
Remove the spacer from the front of the crankshaft.
Cat SIS web machinery list:
Parts shroud Caterpillar catalog:
324D L, 325D L, 330D L, 336D L, 336D2, 336D2 L, 336E L, 345C, 345D L, 349D L, 349E L, 349E L VG, 365B II, 365C, 374D L, 374F L, 988K, 990H, 990K, 992G
3535552
SHROUD AS
324D, 324D FM, 324D L, 325D, 325D FM, 325D L, 326D L, 329D, 329D L
324D, 324D FM, 324D L, 325D, 325D FM, 325D L, 326D L, 329D, 329D L
2302793
SHROUD AS
345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, W345C MH
345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, W345C MH
2653544
SHROUD AS-RADIATOR
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, M330D
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, M330D
2813539
SHROUD AS
365C, 365C L, 374D L
365C, 365C L, 374D L
3588124
SHROUD AS
330D L, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L
330D L, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L
3479749
SHROUD-RADIATOR
336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L
336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L
3354193
SHROUD-RADIATOR
349E, 349E L, 349E L HVG, 349E L VG, 349F L
349E, 349E L, 349E L HVG, 349E L VG, 349F L
3512423
SHROUD-FAN
349E, 349E L, 349E L HVG, 349E L VG, 349F L
349E, 349E L, 349E L HVG, 349E L VG, 349F L
1398876
SHROUD AS
365B, 365B II, 365B L
365B, 365B II, 365B L
2459337
SHROUD AS
365C, 365C L, 365C L MH
365C, 365C L, 365C L MH
3607710
SHROUD-RADIATOR
374F L, 390F L
374F L, 390F L
324D L, 325D L, 330D L, 336D L, 336D2, 336D2 L, 336E L, 345C, 345D L, 349D L, 349E L, 349E L VG, 365B II, 365C, 374D L, 374F L, 988K, 990H, 990K, 992G
2400105
SHROUD AS
966H, 972H, 980C
966H, 972H, 980C
1860119
SHROUD AS
950G II, 962G II
950G II, 962G II
1835496
SHROUD AS-FAN
966G II, 972G II
966G II, 972G II
1317812
SHROUD AS-FAN
834G, 834H, 988G, 988H, AD55B, AD60
834G, 834H, 988G, 988H, AD55B, AD60
1127253
SHROUD AS
854G, 992G
854G, 992G
385B, 385C L, 390D, 390D L, 390F L, 992K, 993K, R1300G, R1600G, R1600H, R1700G, R2900G, R3000H
385B, 385C L, 390D, 390D L, 390F L, 992K, 993K, R1300G, R1600G, R1600H, R1700G, R2900G, R3000H
2790415
SHROUD AS
854K, 992K
854K, 992K
2342441
SHROUD AS
980H
980H