parts catalog

SIDE AS (LH) 2500601 - Caterpillar

2500601 SIDE AS (LH) Caterpillar parts SIDE
Alternative (cross code) number:
Caterpillar 2500601 SIDE AS (LH)

Buy SIDE AS (LH) 2500601 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register


Adjustment of the Oil Change Interval
Note: Your Cat dealer has additional information on these programs.Program A
Verification for an Oil Change Interval of 500 HoursThis program consists of three oil change intervals of 500 hours. Oil sampling and analysis is done at 250 hours and 500 hours for each of the three intervals for a total of six oil samples. The analysis includes oil viscosity and infrared (IR) analysis of the oil. If all the results are satisfactory, the 500 hour oil change interval is acceptable for the machine in that application. Repeat Program A if you change the application of the machine.If a sample does not pass the oil analysis, take one of these actions:
Shorten the oil change interval to 250 hours.
Proceed to Program B.
Change to a preferred oil type in Table 1.Program B
Optimizing Oil Change IntervalsBegin with a 250 hour oil change interval. The oil change intervals are adjusted by increments. Each interval is adjusted an additional 50 hours. Periodic oil sampling and analysis is done during each interval. The analysis includes oil viscosity and infrared (IR) analysis of the oil. Repeat Program B if you change the application of the machine.If an oil sample does not pass the analysis, shorten the oil change interval, or change to a preferred multigrade oil type in the listing above.References
Reference: Form, PEDP7035, "Optimizing Oil Change Intervals"Reference: Form, PEDP7036, "S O S Fluid Analysis"Reference: Form, PEHP7076, "Understanding the S O S Oil Analysis Tests"Procedure for Changing the Engine Oil and Filter
Hot oil and components can cause personal injury.Do not allow hot oil or components to contact skin.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Open the engine access door on the left side of the machine.
Illustration 1 g06025765If the machine is equipped with a high speed oil change, use a 126-7539 Nozzle.
Illustration 2 g00490801
Remove two bolts to remove the crankcase drain access cover, which is in the crankcase guard.
Illustration 3 g00670611
Remove the 4P-0520 Plug Adapter from the drain valve, if equipped.
Install a 25.4 mm (1.00 inch) pipe into the drain valve. The pipe requires a 1-11 1/2 NPTF pipe thread.
Open the drain valve. Allow the oil to drain into a suitable container. A drain hose may be attached to the pipe to aid in draining.
When the oil has completed draining from the crankcase, close the drain valve. Remove the pipe. Install the 4P-0520 Plug Adapter. Install the access cover.
Illustration 4 g06127241
Right Engine Access Door
Remove engine oil filter element (1) and discard the engine oil filter element properly. Make sure that all the old filter seal is removed from the filter base.
Apply a thin coat of oil to the seal on

Parts side Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.