3801201 SIDECUTTER Caterpillar parts
311F LRR, 312C L, 312D, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 314D CR, 314D LCR, 314E CR, 314E LCR, M313D, M315D 2
Rating:
Alternative (cross code) number:
CA3801201
380-1201
3801201
CA3801201
380-1201
3801201
Weight: 18 pounds 8 kg.
EXCAVATOR, WHEELED EXCAVATOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Kairak 3801201 Caster 6" Swivel with Brake 5-3
Kairak Genuine OEM replacement part || Kairak manufactures unique and customized commercial refrigeration equipment || Use genuine OEM parts for safety reliability and performance
Kairak Genuine OEM replacement part || Kairak manufactures unique and customized commercial refrigeration equipment || Use genuine OEM parts for safety reliability and performance
Kairak 3801201 Caster 6" Swivel with Brake 5-3
Kairak Genuine OEM replacement part || Kairak manufactures unique and customized commercial refrigeration equipment || Use genuine OEM parts for safety reliability and performance
Kairak Genuine OEM replacement part || Kairak manufactures unique and customized commercial refrigeration equipment || Use genuine OEM parts for safety reliability and performance
Number on catalog scheme:
1
For full view, you need register
Compatible equipment models: 3801201:
Information:
Illustration 1 g01941814
Circuit of the transmission pump bypass solenoid
This diagnostic code is associated with the transmission pump bypass solenoid. The FMI 03 means that the transmission/chassis electronic control module (ECM) has determined that the voltage of the solenoid circuit is above normal. The possible causes of the diagnostic code are listed:
The solenoid has failed.
The energize circuit of the solenoid is shorted to the +battery circuit.
The transmission/chassis ECM has failed. This is unlikely.Before performing this procedure, inspect the harness connectors that are involved in the circuit. Poor connections can often be the cause of a problem in an electrical circuit. Verify that all connections in the circuit are clean, that all connections are secure and that all connections are in good condition. If a problem with a connection is found, correct the problem and verify that this diagnostic code is active before performing this procedure. Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 3210 FMI 03 is active before performing this procedure.Use a calibrated digital multimeter for the following procedures.System Response:The diagnostic code of CID 3210 FMI 03 will be logged in the internal memory of the transmission/chassis ECM.Test Step 1. CHECK THE ENERGIZE CIRCUIT OF THE SOLENOID FOR A SHORT TO THE +BATTERY CIRCUIT.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness connectors from the solenoid and the transmission/chassis ECM.
At the machine harness connector for the transmission/chassis ECM, measure the resistance from contact J1-65 (wire X961-GY(Grey)) to all contacts that are used in the machine harness connectors for the transmission/chassis ECM. Expected Result:Each resistance measurement is greater than 5000 ohms. Results:
OK - Each resistance measurement is greater than 5000 ohms. The machine harness is correct. Proceed to Test Step 2.
NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between J1-65 (wire X961-GY(Grey)) and the circuit that has a low resistance measurement. Repair: Repair the machine harness or replace the machine harness. For information on testing for short circuits and finding short circuits, refer to Testing and Adjusting, "Wiring Harness (Short Circuit) - Test". Repair the machine harness or replace the machine harness.STOPTest Step 2. CHECK THE RETURN CIRCUIT OF THE SOLENOID FOR A SHORT TO +BATTERY.
The key start switch remains in the OFF position.
The solenoid remains disconnected from the machine harness.
The machine harness connectors J1 and J2 remain disconnected from the transmission/chassis ECM.
At the machine harness for the solenoid, measure the voltage between the contact for (wire K927-BU(Blue)) and frame ground. Expected Result:The voltage is approximately 0.0 0.5 DCV.Results:
OK - The voltage is approximately 0.0 0.5 DCV. The voltage is correct. Proceed to Test Step 3.
NOT OK - Each resistance measurement is not greater than 5000 ohms. There is a short in the machine harness. The short is between
Caterpillar parts catalog:
Parts sidecutter Caterpillar catalog:
4I7343
SIDECUTTER GP
311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312C L, 312D, 312D L, 312E, 313B, 314C, 314D LCR, 314E CR, E110B, E120B, M312, M315
311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312C L, 312D, 312D L, 312E, 313B, 314C, 314D LCR, 314E CR, E110B, E120B, M312, M315
3801203
SIDECUTTER GP
311F LRR, 312C L, 312D, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 314D CR, 314D LCR, 314E CR, 314E LCR, M313D, M315D 2
311F LRR, 312C L, 312D, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 314D CR, 314D LCR, 314E CR, 314E LCR, M313D, M315D 2
311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312C L, 312D, 312D L, 312E, 313B, 314C, 314D LCR, 314E CR, E110B, E120B, M312, M315
311, 311B, 311C, 311D LRR, 311F LRR, 312, 312B, 312C L, 312D, 312D L, 312E, 313B, 314C, 314D LCR, 314E CR, E110B, E120B, M312, M315
3801202
SIDECUTTER
311F LRR, 312C L, 312D, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 314D CR, 314D LCR, 314E CR, 314E LCR, M313D, M315D 2
311F LRR, 312C L, 312D, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 314D CR, 314D LCR, 314E CR, 314E LCR, M313D, M315D 2
3940311
SIDECUTTER
311D LRR, 312D, 312D L, 312D2, 312D2 GC, 312E, 314D CR, 314D LCR, 316E L, 318D L, 318D2 L, M313D, M315D 2
311D LRR, 312D, 312D L, 312D2, 312D2 GC, 312E, 314D CR, 314D LCR, 316E L, 318D L, 318D2 L, M313D, M315D 2
3940317
SIDECUTTER
311D LRR, 312D, 312D L, 312D2, 312D2 GC, 312E, 314D CR, 314D LCR, 316E L, 318D L, 318D2 L, M313D, M315D 2
311D LRR, 312D, 312D L, 312D2, 312D2 GC, 312E, 314D CR, 314D LCR, 316E L, 318D L, 318D2 L, M313D, M315D 2
1917469
SIDECUTTER
304.5
304.5
1917468
SIDECUTTER
304.5
304.5
318C, 320B, 320C, 320D, 320D L, 320D LN, 320D LRR, 320D RR, 320E LN, 320E LRR, 321C, 321D LCR, 322C, 323D L, 323E L, 324D, 324D L, 324E, 324E L, 324E LN, 325, 325 L, 325B, 325B L, 325C, 325D, 325D L, ...
318C, 320B, 320C, 320D, 320D L, 320D LN, 320D LRR, 320D RR, 320E LN, 320E LRR, 321C, 321D LCR, 322C, 323D L, 323E L, 324D, 324D L, 324E, 324E L, 324E LN, 325, 325 L, 325B, 325B L, 325C, 325D, 325D L, ...
1531647
SIDECUTTER
307B, 307C, 307D, 308E CR, 308E SR
307B, 307C, 307D, 308E CR, 308E SR
1531646
SIDECUTTER
307B, 307C, 307D, 308E CR, 308E SR
307B, 307C, 307D, 308E CR, 308E SR
3692642
SIDECUTTER
307D, 307E, 308E
307D, 307E, 308E
3940317
SIDECUTTER
311D LRR, 312D, 312D L, 312D2, 312D2 GC, 312E, 314D CR, 314D LCR, 316E L, 318D L, 318D2 L, M313D, M315D 2
311D LRR, 312D, 312D L, 312D2, 312D2 GC, 312E, 314D CR, 314D LCR, 316E L, 318D L, 318D2 L, M313D, M315D 2
3940311
SIDECUTTER
311D LRR, 312D, 312D L, 312D2, 312D2 GC, 312E, 314D CR, 314D LCR, 316E L, 318D L, 318D2 L, M313D, M315D 2
311D LRR, 312D, 312D L, 312D2, 312D2 GC, 312E, 314D CR, 314D LCR, 316E L, 318D L, 318D2 L, M313D, M315D 2
3572714
SIDECUTTER
315D L, 316E L, 318D L, 318D2 L, 320D, 320D GC, 320D2, 320D2 GC, 323D L, 323D2 L, M317D 2
315D L, 316E L, 318D L, 318D2 L, 320D, 320D GC, 320D2, 320D2 GC, 323D L, 323D2 L, M317D 2
3572713
SIDECUTTER
315D L, 316E L, 318D L, 318D2 L, 320D, 320D GC, 320D2, 320D2 GC, 323D L, 323D2 L, M317D 2
315D L, 316E L, 318D L, 318D2 L, 320D, 320D GC, 320D2, 320D2 GC, 323D L, 323D2 L, M317D 2
3801202
SIDECUTTER
311F LRR, 312C L, 312D, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 314D CR, 314D LCR, 314E CR, 314E LCR, M313D, M315D 2
311F LRR, 312C L, 312D, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 314D CR, 314D LCR, 314E CR, 314E LCR, M313D, M315D 2