SLACK ADJUSTER GP 2050558 - Caterpillar

2050558 SLACK ADJUSTER GP Caterpillar parts 777D, 789C, 789D

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA2050558
205-0558
2050558

Weight: 21 pounds 9 kg.

Buy SLACK ADJUSTER GP 2050558 Caterpillar genuine, new aftermarket tractor parts with delivery
TRUCK,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

GRPP 10 pcs Bags fits - Vacuum 20-5055 20-50557 20-50558

$29.98

17 Dec 2023

US: GR Parts

GRPP 10 pcs Bags fits - Vacuum 20-5055 20-50557 20-50558
GRPP More than 10,000 positions: You will find a wide selection of garden equipment parts in our store - from spark plugs to belts, cutting blades, batteries, crankshafts, bearings, carburetors, starters, filters, and repair kits. In our product range, we have more than 10.000 garden equipment parts. || Compatible with: Vacuum 20-5055 20-50557 20-50558 || NOT an OEM part. || GR Parts: Replacement parts for most types of lawnmowers, trimmers, snowblowers, tractors, chainsaws, pressure washers, edgers, tillers and generators. || All parts are manufactured with the highest standards and under rigorous quality controls. As a result, you always get perfectly fitting, durable, wear-resistant, high-performing replacement parts, and never get mismatched or underperforming equipment.

(50-Packs) Bags Suitable Kеnmоrе 20-5055, 20-50558 C Vacuum Cleaner Bag Progressive

$41.23

29 Oct 2019

-: -

(50-Packs) Bags Suitable Kеnmоrе 20-5055, 20-50558 C Vacuum Cleaner Bag Progressive
50 Bags for Kenmore 20-5055, 20-50558 C Vacuum Cleaner Bag Progressive

(50-Packs) Vacuum Bags Suitable Kеnmоrе 20-5055, 20-50557, 20-50558

$41.23

03 Oct 2019

-: -

(50-Packs) Vacuum Bags Suitable Kеnmоrе 20-5055, 20-50557, 20-50558
50 Vacuum Bags for Kenmore 20-5055, 20-50557, 20-50558

This part in 1 request: Show. This information for suppliers only!

#5081 205-0558

2016-05-03

Number on catalog scheme: 35

Caterpillar 2050558 Parts scheme SLACK ADJUSTER GP

For full view, you need register

Compatible equipment models: 2050558:

TRUCK 777D 789C 789D Caterpillar

Information:

Illustration 51 g00521797
Typical Governor (1) Bolt (2) Orifice for the dashpot (3) O-ring seal (4) Bolt (5) Cover (6) Cover assembly (7) O-ring seal (8) Shims (9) Rear spring seat (10) Retaining ring (11) Spacer (12) Piston assembly for the dashpot (13) Shims for the high idle governor (if equipped) (14) Spring pair (15) Spring seat assembly
Illustration 52 g00522519
Illustration 53 g00522517
Screw the coils of spring pair (14) onto spring seat assembly (15). Align the springs so that the springs are even with the spring seat and each other.
Illustration 54 g00522516
Slide spring seat assembly (15) onto the riser shaft with the springs toward the outside.Note: Rotate the springs on the spring seat so that the inner spring is aligned with the outer spring. Remove the sharp edges from the flat surface on the inside diameter of the springs. This will ensure that the springs are seated properly on the spring seat.
Illustration 55 g00522514
Install shims (13) for the governor high idle, if necessary.
Illustration 56 g00522509
Install shims (8) for the high idle governor (if equipped) and spacer (11) onto governor spring seat (9) .
Illustration 57 g00521803
Install governor spring seat (9) onto the riser shaft.
Illustration 58 g00521802
Remove O-ring seal (7). Lightly lubricate the bore of the governor rear housing with clean engine oil and loosely install cover (6). Drain the oil from cover (6) into a suitable container for storage or disposal.
Illustration 59 g00521801
Put cover assembly (6) in position on the governor. Install three bolts (1) and evenly tighten the bolts.
Ensure that orifice (2) for the dashpot is not plugged. Also ensure that orifice (2) is tight in the casting.
Illustration 60 g00521800
Install O-ring seal (3) onto cover (5) .
Illustration 61 g00521798
Put cover (5) in position on cover assembly (6) and install three bolts (4) .
Illustration 62 g00654412
Note: Before performing Step 72, the low idle screw must be backed out completely so that the throttle lever contacts the governor housing. The low idle adjustment is made during governor calibration.
Install the 1U-7308 Shim Adjustment Tool (Tool (K) ) and put the dial indicator point on the center of the rear cover. Push down on the rear cover until the cover makes contact with the governor housing. Zero the dial indicator. Slowly release the pressure on the rear cover. As the cover is pushed out by the force of the spring under the cover, rotate the cover for approximately 90 degrees. The reading on the dial indicator will determine the amount of preload on the spring. Add shims or remove shims in order to establish the proper preload on the spring. Refer to the Technical Marketing Information (TMI) for the governor spring preload dimension according to the governor group number.Note: The rear cover assembly must move freely.Note: The preload dimension that is stated in the TMI should only be used for reference. The manufacturer of the governor is not required to meet the specification. The number of governor spring shims is determined by the governor test bench calibration. Governor spring shims are added in order to increase the tension on the high idle screw. Governor spring shims