3256209 SLEEVE-YM Caterpillar parts
Rating:
Alternative (cross code) number:
CA3256209
325-6209
3256209
CA3256209
325-6209
3256209
Weight: 47 pounds 21 kg.
Related part:
3T1162
SLEEVE-YM
3256209
CL
Information:
Illustration 1 g00791326
Schematic of the Proportional Solenoid (Reverse) for the Right Drive PumpThis diagnostic code is recorded when the ECM reads the voltage of the solenoid circuit as being above normal.The possible causes for this diagnostic code are listed:
The circuit of the solenoid is shorted to the +battery circuit.
The ECM has failed. This is unlikely.Note: Ensure that the CID 1706 FMI 03 for the solenoid is on hold.System Response:When this diagnostic code occurs, the action lamp and the action alarm is ON. This diagnostic code will cause the transmission to shift to NEUTRAL until the diagnostic code is corrected.Test Step 1. CHECK THE SOLENOID CIRCUIT FOR A SHORT TO THE +BATTERY CIRCUIT.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the machine harness from the solenoid.
Disconnect the machine harness connectors J1 and J2 from the ECM.
At machine harness connector J1 and J2, measure the resistance. Measure the resistance from the signal contact J2-63 (wire K946-OR) to all contacts that are used in the machine harness connectors for the ECM.Expected Result:The resistance should be greater than 5000 ohms for each measurement.Results:
OK - The resistance is greater than 5000 ohms for each measurement. The machine harness is correct. Proceed to test step 2.
NOT OK - The resistance is NOT greater than 5000 ohms for each measurement. The resistance is NOT correct. There is a short in the machine harness. The short is between signal contact J2-63 (wire K946-OR) and the circuit with the low resistance measurement.Repair: Repair the harness or replace the harness.STOPTest Step 2. CHECK IF THE DIAGNOSTIC CODE REMAINS.
Inspect the contacts and clean the contacts of the harness connectors.
Reconnect all harness connectors.
Turn the disconnect switch and the key start switch to the ON position.
Clear all inactive diagnostic codes.
Operate the machine.
Observe the status of the diagnostic code for the solenoid.Expected Result:The diagnostic code for the solenoid is NOT present. Results:
YES - The diagnostic code is NOT present. The diagnostic code does not exist at this time. Repair: The initial diagnostic code was probably caused by a poor electrical connection or a short at one of the harness connectors that was disconnected and reconnected. Resume normal machine operation.STOP
NO - The diagnostic code has not been corrected. The ECM has failed.Repair: It is unlikely that the ECM has failed. Exit this procedure and perform this diagnostic code procedure again. If the cause of the diagnostic code is not found, replace the ECM. See Testing and Adjusting, "Electronic Control Module (ECM) - Replace".STOP
Caterpillar parts catalog:
Parts sleeve Caterpillar catalog:
3853795
SLEEVE-YM
Caterpillar
Caterpillar
3843848
SLEEVE-YM
Caterpillar
Caterpillar
3933673
SLEEVE-LINK-YM
Caterpillar
Caterpillar
3933659
SLEEVE-YM
Caterpillar
Caterpillar
3919905
SLEEVE-YM
Caterpillar
Caterpillar
3940218
SLEEVE-YM
Caterpillar
Caterpillar
2262720
SLEEVE-YM
Caterpillar
Caterpillar
2260235
SLEEVE-RECOIL-YM
Caterpillar
Caterpillar
2260234
SLEEVE-YM
Caterpillar
Caterpillar
2992059
SLEEVE-YM
Caterpillar
Caterpillar
3148720
SLEEVE-YM
Caterpillar
Caterpillar
3256210
SLEEVE-PUMP-YM
Caterpillar
Caterpillar