5G0387 SLIP JOINT GP Caterpillar parts
910, G910, IT12
Rating:
Alternative (cross code) number:
CA5G0387
5G-0387
5G0387
CA5G0387
5G-0387
5G0387
Weight: 21 pounds 9 kg.
COMPACT WHEEL LOADER, WHEEL LOADER,
Compatible equipment models: 5G0387:
Information:
Remove Pistons
Start By:a. remove cylinder head assembliesb. remove oil pumpc. remove piston cooling tubes
If the piston cooling tubes are not removed, it is possible for the connecting rod to hit the piston cooling tubes. This can move the piston cooling tube out of alignment. A piston cooling tube that is not in alignment will not direct the lubricant to the correct location. The result can be piston seizure.
1. Remove the carbon from the top inside surface of the cylinder liners.2. Turn the crankshaft with Tool (A) until two pistons are at bottom center. 3. Remove bearing caps (1) from the two connecting rods. Put pieces of rubber hose or tape on the threads of the connecting rod bolts as protection for the crankshaft. 4. Push the pistons up until the piston rings are clear of the cylinder liner. Remove pistons (2). Keep each cap with the respective connecting rod.
Do not turn the crankshaft while any of the connecting rods are in the engine without the caps installed. Do not damage the cooling tubes when the pistons are removed.
5. Do steps 1 through 4 for the remainder of the pistons.Install Pistons
1. Put clean engine oil on the piston rings, connecting rod bearings and cylinder liners. 2. Put two pistons in position opposite of each other in the correct bore of the block. Install pistons (1) with tool (A).
Be sure that the pistons are installed with flat surfaces (2) of the connecting rod toward each other and the chamfered sides (4) toward the crankshaft.
For more detail about checking bearing clearances and installation of connecting rod bearings, see Remove & Install Connecting Rod Bearings.3. Check the bearing clearances with Plastigage.4. Put 2P2506 Thread Lubricant on bolts (5). Install caps (3) and nuts finger tight. Tighten each nut to a torque of 80 8 N m (60 6 lb ft). Put a mark across the nut and bolts. Tighten each nut 120° more.
Do not use an impact wrench to tighten the nuts the additional 120° more.
5. Check the side clearance between two connecting rods on the same crankshaft journal. Clearance must be 0.28 to 0.84 mm (.011 to .033 in) for new rods.6. Do Steps 1 thru 5 for the remainder of the pistons.End By:a. install piston cooling tubesb. install oil pumpc. install cylinder head assembliesDisassemble & Assemble Pistons (Earlier - Rod Pin Bearing With Straight Sides)
Start By:a. remove pistons1. Remove the bearings from the connecting rod and connecting rod cap. 2. Remove retainer ring (1) with Tool (C).3. Remove pin (2) and the connecting rod (4) from the piston (3). 4. Remove the piston rings from the piston with Tool (A). Clean the piston ring grooves on the pistons with an acceptable ring groove cleaning rod. See Use of Pistons Pin Bearing Removal & Installation Tools, Special Instruction, Form No. SMHS7295.5. Heat the connecting rod in an oven to a temperature of 177° to 260°C (350 to 500°F). Never use a direct flame to heat a connecting rod. 6.
Start By:a. remove cylinder head assembliesb. remove oil pumpc. remove piston cooling tubes
If the piston cooling tubes are not removed, it is possible for the connecting rod to hit the piston cooling tubes. This can move the piston cooling tube out of alignment. A piston cooling tube that is not in alignment will not direct the lubricant to the correct location. The result can be piston seizure.
1. Remove the carbon from the top inside surface of the cylinder liners.2. Turn the crankshaft with Tool (A) until two pistons are at bottom center. 3. Remove bearing caps (1) from the two connecting rods. Put pieces of rubber hose or tape on the threads of the connecting rod bolts as protection for the crankshaft. 4. Push the pistons up until the piston rings are clear of the cylinder liner. Remove pistons (2). Keep each cap with the respective connecting rod.
Do not turn the crankshaft while any of the connecting rods are in the engine without the caps installed. Do not damage the cooling tubes when the pistons are removed.
5. Do steps 1 through 4 for the remainder of the pistons.Install Pistons
1. Put clean engine oil on the piston rings, connecting rod bearings and cylinder liners. 2. Put two pistons in position opposite of each other in the correct bore of the block. Install pistons (1) with tool (A).
Be sure that the pistons are installed with flat surfaces (2) of the connecting rod toward each other and the chamfered sides (4) toward the crankshaft.
For more detail about checking bearing clearances and installation of connecting rod bearings, see Remove & Install Connecting Rod Bearings.3. Check the bearing clearances with Plastigage.4. Put 2P2506 Thread Lubricant on bolts (5). Install caps (3) and nuts finger tight. Tighten each nut to a torque of 80 8 N m (60 6 lb ft). Put a mark across the nut and bolts. Tighten each nut 120° more.
Do not use an impact wrench to tighten the nuts the additional 120° more.
5. Check the side clearance between two connecting rods on the same crankshaft journal. Clearance must be 0.28 to 0.84 mm (.011 to .033 in) for new rods.6. Do Steps 1 thru 5 for the remainder of the pistons.End By:a. install piston cooling tubesb. install oil pumpc. install cylinder head assembliesDisassemble & Assemble Pistons (Earlier - Rod Pin Bearing With Straight Sides)
Start By:a. remove pistons1. Remove the bearings from the connecting rod and connecting rod cap. 2. Remove retainer ring (1) with Tool (C).3. Remove pin (2) and the connecting rod (4) from the piston (3). 4. Remove the piston rings from the piston with Tool (A). Clean the piston ring grooves on the pistons with an acceptable ring groove cleaning rod. See Use of Pistons Pin Bearing Removal & Installation Tools, Special Instruction, Form No. SMHS7295.5. Heat the connecting rod in an oven to a temperature of 177° to 260°C (350 to 500°F). Never use a direct flame to heat a connecting rod. 6.
Caterpillar SIS machinery equipment:
Caterpillar SIS
910 WHEEL LOADER 80U06735-UP (MACHINE) POWERED BY 3204 ENGINE »
5G-0387
SLIP JOINT GP
910 WHEEL LOADER 40Y00001-UP (MACHINE) POWERED BY 3204 ENGINE »
5G-0387
SLIP JOINT GP
910 WHEEL LOADER 41Y00001-UP (MACHINE) POWERED BY 3204 ENGINE »
5G-0387
SLIP JOINT GP
IT12 INTEGRATED TOOLCARRIER 2YC00001-UP (MACHINE) POWERED BY 3204 ENGINE »
5G-0387
SLIP JOINT GP
G910 WHEEL LOADER 3SD00001-UP (MACHINE) POWERED BY 3204 ENGINE »
5G-0387
SLIP JOINT GP
910 WHEEL LOADER 80U00001-06734 (MACHINE) »
5G-0387
SLIP JOINT GP
Caterpillar parts catalog:
Parts slip Caterpillar catalog:
5G0388
SLIP JOINT GP
910, G910, IT12
910, G910, IT12
7V4083
SLIP JOINT GP
528, 528B, 530B
528, 528B, 530B
8R6830
SLIP JOINT GP
930R
930R
1151651
SLIP JOINT GP
938K, 950G, 950G II, 950H, 950K, 962G, 962G II, IT62G
938K, 950G, 950G II, 950H, 950K, 962G, 962G II, IT62G
7V3781
SLIP JOINT GP
926, 926A, G926, IT28, IT28B
926, 926A, G926, IT28, IT28B
8Y1115
SLIP JOINT GP
910E, IT12B
910E, IT12B
9C8369
SLIP JOINT GP
936, 936F, G936
936, 936F, G936
2T0091
SLIP JOINT GP
615, 615C
615, 615C
1572009
SLIP JOINT GP
773D, 773E, 773F, 775D, 775E, 775F
773D, 773E, 773F, 775D, 775E, 775F
1064014
SLIP JOINT GP
515, 525
515, 525
2093421
SLIP JOINT GP
D10N, D10R, D8T
D10N, D10R, D8T
1411821
SLIP JOINT GP
515, 525
515, 525
2V4778
SLIP JOINT GP
992C
992C