2068781 SOLENOID AS Caterpillar parts
3116, 3126, 3126B, 3126E, 322C, 322C FM, 324D, 324D LN, 325C, 325C FM, 325D, 325D L, 539, 543, 613C II, 963B, 963C, AP-1000B, AP-900B, BG-2455C, BG-245C, C13, C7, CS-531C, CS-531D, CS-533C, CS-533D, C...
Rating:
Alternative (cross code) number:
CA2068781
206-8781
2068781
CA2068781
206-8781
2068781
Weight: 3 pounds 1 kg.
ASPHALT PAVER, WHEELED EXCAVATOR,
This part in 5 request:
Show.
This information for suppliers only!
2024-05-03
2024-05-03
2024-05-02
2023-10-25
2023-10-23
Compatible equipment models: 2068781:
Information:
Remove Cylinder Liners
start by:a) remove pistons1. Check to be sure that all coolant has been removed from the cylinder block.2. Put a cover over the crankshaft journals before liners are removed. 3. Install tool (A) and remove the cylinder liners. 4. Remove filler band (1) and O-ring seals (2) from the cylinder liners.Install Cylinder Liners
1. Clean the cylinder liners and cylinder block. 2. Install the liners (1) in the cylinder block without the O-ring seals and filler bands. See CYLINDER LINER PROJECTION in TESTING AND ADJUSTING. 3. Install tooling (A) and two 5/8" - 11 NC bolts 5 1/2 in. long. Tighten the bolts evenly to 50 lb.ft. (70 N m).4. Check the liner projection with tool (B) at four locations around the liner.5. Liner projection must be .0020 to .0056 in. (0.051 to 0.142 mm). Measurements on the same liner must not be different by more than .002 in. (0.05 mm). Average measurement between liners next to each other must not be different by more than .002 in. (0.05 mm). The maximum permissible difference between average projection of all cylinder liners under one cylinder head is .004 in. (0.10 mm). The liner projection can change if the liner is turned in the bore. 6. If the liner projection is not .0020 to .0056 in. (0.051 to 0.142 mm), check the thickness of the liner flange (2) and the depth of the liner bore in the cylinder block. The thickness of the liner flange (2) must be .4048 .0008 in. (10.282 0.020 mm).7. The depth of the liner bore in the cylinder block must be .401 .001 in. (10.19 0.03 mm). If the liner bore in the block is worn and the measurement is not correct, the liner bore can be corrected with a cylinder block counterboring tool. See SPECIAL INSTRUCTIONS, FORM FM055228.8. Put a mark on the liner and cylinder block so the liner can be installed in the same position from which it was removed. 9. Install new O-ring seals (4) on the cylinder liners. Put liquid soap on the O-ring seals and in the bases in the cylinder block.
The liners must be installed in the cylinder block immediately after filler band (3) is installed. Make sure the marks on the liners and the cylinder block are in alignment when the cylinder liners are installed.
10. Put (dip) the filler band completely in clean SAE 30 oil and install it on the liner immediately.11. Install the liner in the cylinder block immediately with tooling (C).end by:a) install pistons
start by:a) remove pistons1. Check to be sure that all coolant has been removed from the cylinder block.2. Put a cover over the crankshaft journals before liners are removed. 3. Install tool (A) and remove the cylinder liners. 4. Remove filler band (1) and O-ring seals (2) from the cylinder liners.Install Cylinder Liners
1. Clean the cylinder liners and cylinder block. 2. Install the liners (1) in the cylinder block without the O-ring seals and filler bands. See CYLINDER LINER PROJECTION in TESTING AND ADJUSTING. 3. Install tooling (A) and two 5/8" - 11 NC bolts 5 1/2 in. long. Tighten the bolts evenly to 50 lb.ft. (70 N m).4. Check the liner projection with tool (B) at four locations around the liner.5. Liner projection must be .0020 to .0056 in. (0.051 to 0.142 mm). Measurements on the same liner must not be different by more than .002 in. (0.05 mm). Average measurement between liners next to each other must not be different by more than .002 in. (0.05 mm). The maximum permissible difference between average projection of all cylinder liners under one cylinder head is .004 in. (0.10 mm). The liner projection can change if the liner is turned in the bore. 6. If the liner projection is not .0020 to .0056 in. (0.051 to 0.142 mm), check the thickness of the liner flange (2) and the depth of the liner bore in the cylinder block. The thickness of the liner flange (2) must be .4048 .0008 in. (10.282 0.020 mm).7. The depth of the liner bore in the cylinder block must be .401 .001 in. (10.19 0.03 mm). If the liner bore in the block is worn and the measurement is not correct, the liner bore can be corrected with a cylinder block counterboring tool. See SPECIAL INSTRUCTIONS, FORM FM055228.8. Put a mark on the liner and cylinder block so the liner can be installed in the same position from which it was removed. 9. Install new O-ring seals (4) on the cylinder liners. Put liquid soap on the O-ring seals and in the bases in the cylinder block.
The liners must be installed in the cylinder block immediately after filler band (3) is installed. Make sure the marks on the liners and the cylinder block are in alignment when the cylinder liners are installed.
10. Put (dip) the filler band completely in clean SAE 30 oil and install it on the liner immediately.11. Install the liner in the cylinder block immediately with tooling (C).end by:a) install pistons
Caterpillar parts catalog:
Parts solenoid Caterpillar catalog:
1204187
SOLENOID GP-THROTTLE
CB-434C, CB-534C, CB-535B, CB-634C, CP-433E, CS-423E, CS-433E, CS-531D, CS-533D, CS-533E, CS-563D, CS-573D, CS-583D, CS-663E, CS-683E, PM-465, PS-150C, PS-360C, RM-350B
CB-434C, CB-534C, CB-535B, CB-634C, CP-433E, CS-423E, CS-433E, CS-531D, CS-533D, CS-533E, CS-563D, CS-573D, CS-583D, CS-663E, CS-683E, PM-465, PS-150C, PS-360C, RM-350B
7C9458
SOLENOID GP-SHUTOFF
3114, 3116, 3126, 550, 570, 574, 580, AP-1000B, AP-1055B, AP-900B, BG-2455C, BG-245C, CB-434
3114, 3116, 3126, 550, 570, 574, 580, AP-1000B, AP-1055B, AP-900B, BG-2455C, BG-245C, CB-434
1255771
SOLENOID AS
3114, 3116, 3126, AP-1000, AP-1050, RT100
3114, 3116, 3126, AP-1000, AP-1050, RT100
9X9511
SOLENOID AS
120G, 12G, 12H, 12H ES, 12H NA, 130G, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 1673C, 16G, 227, 3116, 3126, 3126B, 3176B, 3176C, 3196, 3208, 320B, 322B, ...
120G, 12G, 12H, 12H ES, 12H NA, 130G, 140G, 140H, 140H ES, 140H NA, 143H, 14G, 14H NA, 160G, 160H, 160H ES, 160H NA, 163H NA, 1673C, 16G, 227, 3116, 3126, 3126B, 3176B, 3176C, 3196, 3208, 320B, 322B, ...
1938570
SOLENOID AS-STARTING MOTOR
12H, 12H ES, 12H NA, 140H, 140H ES, 140H NA, 143H, 14H NA, 160H, 160H ES, 160H NA, 163H NA, 1673C, 3116, 3126, 3126B, 3176C, 3196, 3208, 322B L, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 325B,...
12H, 12H ES, 12H NA, 140H, 140H ES, 140H NA, 143H, 14H NA, 160H, 160H ES, 160H NA, 163H NA, 1673C, 3116, 3126, 3126B, 3176C, 3196, 3208, 322B L, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 325B,...
1554651
SOLENOID AS
3114, 3116, 3126, 446B, 446D, CB-634D
3114, 3116, 3126, 446B, 446D, CB-634D
3383453
SOLENOID AS-STARTING MOTOR
1190, 1190T, 120M, 120M 2, 1290T, 12M 2, 12M 3, 12M 3 AWD, 1390, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16H NA, 16M, 2290, 2390, 2391, 2491, 24H, 24M, 2590, 2864C, 3126B, 3...
1190, 1190T, 120M, 120M 2, 1290T, 12M 2, 12M 3, 12M 3 AWD, 1390, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M, 160M 2, 160M 3, 160M 3 AWD, 16H NA, 16M, 2290, 2390, 2391, 2491, 24H, 24M, 2590, 2864C, 3126B, 3...
1554652
SOLENOID AS
120H, 120H ES, 120H NA, 135H, 135H NA, 3114, 3116, 3126, 320B, 322B L, 322B LN, 322C, 322C FM, 325B L, 525B, 533, 535B, 539, 543, 561M, 613C II, 924F, 928G, 938F, 938G, 950F, 950F II, 950G, 953C, 960F...
120H, 120H ES, 120H NA, 135H, 135H NA, 3114, 3116, 3126, 320B, 322B L, 322B LN, 322C, 322C FM, 325B L, 525B, 533, 535B, 539, 543, 561M, 613C II, 924F, 928G, 938F, 938G, 950F, 950F II, 950G, 953C, 960F...
1255772
SOLENOID AS
3114, 3116, 3126, 550, 570, 574, 580, AP-1000B, AP-1055B, AP-900B, BG-2455C, BG-245C, CB-434
3114, 3116, 3126, 550, 570, 574, 580, AP-1000B, AP-1055B, AP-900B, BG-2455C, BG-245C, CB-434
3E7859
SOLENOID AS-STARTER
120H, 120H ES, 120H NA, 135H, 135H NA, 214B, 3116, 3126, 3126B, 3126E, 320B, 322B L, 322B LN, 322C, 322C FM, 325B L, 325C, 325D L, 533, 539, 550, 561M, 570, 570B, 574, 580, 580B, 613C II, 928G, 938F, ...
120H, 120H ES, 120H NA, 135H, 135H NA, 214B, 3116, 3126, 3126B, 3126E, 320B, 322B L, 322B LN, 322C, 322C FM, 325B L, 325C, 325D L, 533, 539, 550, 561M, 570, 570B, 574, 580, 580B, 613C II, 928G, 938F, ...
9X0301
SOLENOID AS
214B, 224B, 3116, 3126, 613C II, 950F, 950F II, 960F, CB-634C, CP-563, IT28F, M318
214B, 224B, 3116, 3126, 613C II, 950F, 950F II, 960F, CB-634C, CP-563, IT28F, M318
7X1955
SOLENOID AS
214B, 3116, E240C
214B, 3116, E240C
9N2508
SOLENOID AS
3208
3208
9X6770
SOLENOID-ROTARY
3406B
3406B
6T9675
SOLENOID AS
3406B
3406B
6T1789
SOLENOID
3406B
3406B
1631536
SOLENOID
3406B, 3406C, D350E, D400E
3406B, 3406C, D350E, D400E
1631538
SOLENOID
3406B, 3406C
3406B, 3406C
1631553
SOLENOID
3176B, 3176C, 3196, 3406E, 735, 740, 834G, 988G, C-10, C-12, C-15, C-16, C-18, C15, D350E II, D400E II
3176B, 3176C, 3196, 3406E, 735, 740, 834G, 988G, C-10, C-12, C-15, C-16, C-18, C15, D350E II, D400E II
1631533
SOLENOID
3176B, 3176C, 3196, 3406E, C-10, C-12, C-15, C-16, C-18, C15, C16, C18
3176B, 3176C, 3196, 3406E, C-10, C-12, C-15, C-16, C-18, C15, C16, C18
1432558
SOLENOID
3176
3176
1436644
SOLENOID
3406B
3406B
1631543
SOLENOID
3306, 3306C
3306, 3306C
1631550
SOLENOID
3176
3176