2750493 SOLENOID Caterpillar parts
C2.2
Rating:
Alternative (cross code) number:
CA2750493
275-0493
2750493
CA2750493
275-0493
2750493
Weight: 0.66 pounds 0 kg.
INDUSTRIAL ENGINE,
This part in 2 request:
Show.
This information for suppliers only!
2017-12-25
2017-12-23
Compatible equipment models: 2750493:
Number on catalog scheme:
2
For full view, you need register
Information:
start by:a) separation of governor from fuel injection pump housing 1. Remove protection caps and felt washers (1) from pumps.2. Use wrench (A) to remove the bushings (2) that hold fuel injection pumps into housing. Remove the seals (3).3. Use extractor (B) to remove pumps from the pump housing. Put identification on the injection pumps as to their location in the pump housing.4. Remove the bonnet (4), ring (5), spring (6), and check valve (7) from barrel (8).5. Remove the plunger assembly (11), washer (10), and spring (9) from barrel.
Be careful not to cause damage to plunger assemblies. Keep same cylinder pump and plunger together, the plunger from one pump can not be installed in another pump.
6. Remove the rack (12) from the housing. 7. Remove the spacers (13) and the lifters (14) from the housing. Keep the spacers and lifters together with identification as to their location in the pump housing. 8. Remove two bolts (16), lock, and two sleeves from the gear assembly.9. Remove the gear assembly (15) from camshaft. 10. Remove two bolts, plate (17), and spacer that hold camshaft in position in pump housing. 11. Remove the camshaft from the pump housing. 12. Use tool group (C) to remove the camshaft bearings from the pump housing.13. Remove the bearings for fuel rack from the pump housing.Assemble Fuel Injection Pump Housing
1. Use tool group (C) to install the camshaft bearings in fuel injection pump housing. Install bearing in governor end of housing so oil hole in bearing is in alignment with oil hole in housing. 2. Use tooling (F) to install bearing with a groove for the rack.3. Use tooling (E) to install the other bearing for the rack. 4. Put clean engine oil on the camshaft. Install the camshaft in the pump housing. 5. Install the spacer, plate (1), and two bolts that hold camshaft in place in pump housing. 6. Put the gear assembly (2) in position on end of camshaft. Be sure the rod (3) is in the groove of camshaft. 7. Install the sleeves (4), lock, and two bolts on the gear assembly. 8. Install the spacers (5) with their respective lifters (6) in pump housing. If new lifters and\or pumps are to be installed, make adjustment of fuel pump timing dimension. See SETTING THE INJECTION PUMP TIMING DIMENSION: OFF ENGINE in 3406 VEHICLE ENGINE, TESTING AND ADJUSTING. 9. Install the rack (7) in the pump housing.10. Assemble the fuel injection pumps as follows: a) Put clean fuel on all parts.b) Install spring, washers, and plunger in the barrel.c) Install the spring, check valve, bonnet, and ring on the barrel.
The plunger from one pump can not be installed in another pump. Do not install the pumps until rack (7) is in center position (centered).
11. Use pointer group (D) to put rack (7) in center position. Push the rack into pointer (D) to get the center position. The rack will be extended .156 in. (3.963 mm) from the end of pump housing
Be careful not to cause damage to plunger assemblies. Keep same cylinder pump and plunger together, the plunger from one pump can not be installed in another pump.
6. Remove the rack (12) from the housing. 7. Remove the spacers (13) and the lifters (14) from the housing. Keep the spacers and lifters together with identification as to their location in the pump housing. 8. Remove two bolts (16), lock, and two sleeves from the gear assembly.9. Remove the gear assembly (15) from camshaft. 10. Remove two bolts, plate (17), and spacer that hold camshaft in position in pump housing. 11. Remove the camshaft from the pump housing. 12. Use tool group (C) to remove the camshaft bearings from the pump housing.13. Remove the bearings for fuel rack from the pump housing.Assemble Fuel Injection Pump Housing
1. Use tool group (C) to install the camshaft bearings in fuel injection pump housing. Install bearing in governor end of housing so oil hole in bearing is in alignment with oil hole in housing. 2. Use tooling (F) to install bearing with a groove for the rack.3. Use tooling (E) to install the other bearing for the rack. 4. Put clean engine oil on the camshaft. Install the camshaft in the pump housing. 5. Install the spacer, plate (1), and two bolts that hold camshaft in place in pump housing. 6. Put the gear assembly (2) in position on end of camshaft. Be sure the rod (3) is in the groove of camshaft. 7. Install the sleeves (4), lock, and two bolts on the gear assembly. 8. Install the spacers (5) with their respective lifters (6) in pump housing. If new lifters and\or pumps are to be installed, make adjustment of fuel pump timing dimension. See SETTING THE INJECTION PUMP TIMING DIMENSION: OFF ENGINE in 3406 VEHICLE ENGINE, TESTING AND ADJUSTING. 9. Install the rack (7) in the pump housing.10. Assemble the fuel injection pumps as follows: a) Put clean fuel on all parts.b) Install spring, washers, and plunger in the barrel.c) Install the spring, check valve, bonnet, and ring on the barrel.
The plunger from one pump can not be installed in another pump. Do not install the pumps until rack (7) is in center position (centered).
11. Use pointer group (D) to put rack (7) in center position. Push the rack into pointer (D) to get the center position. The rack will be extended .156 in. (3.963 mm) from the end of pump housing
Caterpillar parts catalog:
Parts solenoid Caterpillar catalog:
3082313
SOLENOID GP-SHUTOFF
216B, 216B3, 3024C, AP-255E, BB-621C, C2.2, CB-34, CB34B, CB34B XW, CC34B
216B, 216B3, 3024C, AP-255E, BB-621C, C2.2, CB-34, CB34B, CB34B XW, CC34B
3111128
SOLENOID GP-SHUTOFF
3013C, C1.1, C1.5, C2.2, CB-22, CB-334E, CB-34
3013C, C1.1, C1.5, C2.2, CB-22, CB-334E, CB-34
3157817
SOLENOID GP-SHUTOFF
AP-255E, BB-621C, C2.2, CB-34
AP-255E, BB-621C, C2.2, CB-34
216, 216B, 216B3, 226B, 226B3, 232B, 242B, 247B, 247B3, 257B, 3011C, 3013, 3013C, 3024, 3024C, AP-255E, BB-621C, C0.5, C0.7, C1.1, C1.5, C1.6, C2.2, CB-14, CB-22, CB-334E, CB-34, CB34B, CB34B XW, CC34...
2427071
SOLENOID
216, 216B, 226B, 232B, 242B, 247B, 257B, 3013, 3013C, 3014, 3024, 3024C, BB-621C, C1.5, C2.2, CB-214D, CB-214E, CB-22, CB-334D, CB-334E, CB-335D, CB-34
216, 216B, 226B, 232B, 242B, 247B, 257B, 3013, 3013C, 3014, 3024, 3024C, BB-621C, C1.5, C2.2, CB-214D, CB-214E, CB-22, CB-334D, CB-334E, CB-335D, CB-34
3802679
SOLENOID
C1.5, C2.2, CB22B, CB24B, CB32B, CB34B, CB34B XW, CC24B, CC34B
C1.5, C2.2, CB22B, CB24B, CB32B, CB34B, CB34B XW, CC24B, CC34B
2834685
SOLENOID AS
C6.6
C6.6
C4.4, C6.6
120M, 12M, 2470C, 320D GC, 320D L, 323D L, 553C, 613G, 914G, 924H, 924HZ, 928H, 928HZ, 938H, 953D, 963D, AP-600D, AP-655D, AP1000E, AP1055E, AP555E, BG500E, BG600D, BG655D, C4.4, C6.6, CP-44, CP-56, C...
2482641
SOLENOID AS
3054C, CS-323C, CS-423E
3054C, CS-323C, CS-423E
2911295
SOLENOID
3024C, C2.2
3024C, C2.2
3011C, 3013C, 3024C, C1.1, C1.5, C2.2
769C, D348
3L6657
SOLENOID
3306, D320A
3306, D320A
3L6672
SOLENOID
3306, D320A
3306, D320A
6L3040
SOLENOID VALVE
D379, D398
D379, D398
3691658
SOLENOID
323D2 L, 525D, 535D, 545D, 555D, 924K, 930K, 938K, 950 GC, C4.4, C7.1, D6K2
323D2 L, 525D, 535D, 545D, 555D, 924K, 930K, 938K, 950 GC, C4.4, C7.1, D6K2
C3.4