SPACER 1512898 - Caterpillar

SEBE9302-01 August 11, 2005
(Revised September 2005)
U-270
A-195
D-209
O-223
Priority PRODUCT IMPROVEMENT PROGRAM FOR CHECKINGAND FLUSHING DEBRIS FROM THE SERVO HOUSING ON CERTAIN 3412 ENGINES
77511289 PI30859
This Program must be administered assoon as possible. When reporting the repair, use "PI30859" as the Partnumber and "7751" as the Group Number, "56" as the Warranty Claim DescriptionCode and "T" as the SIMS Description Code. Exception: If the repair isdone after failure, use "PI30859" as the Part Number, "7751" as the GroupNumber, "96" as the Warranty Claim Description Code, and "Z" as the SIMSDescription Code. The information supplied in this serviceletter may not be valid after the termination date of this program. Donot perform the work outlined in this Service Letter after the terminationdate without first contacting your Caterpillar product analyst. This Revised Service Letter replacesthe August 11, 2005 Service Letter. Changes have been made to the AffectedProduct.
COMPLETION DATE
TERMINATION DATE
February 28, 2006 August 31, 2006PROBLEM
Debris in oil line on 3412 PEEC engine may cause anoverspeed condition.AFFECTED PRODUCT
Model Identification Number
3412 2WJ8269-8286
SPT342 3CZ421
3412C 4BZ6866, 6878, 6882, 6913,6915, 6920, 6923-6924, 6926, 6932-6935, 6946, 6948-6949, 6951, 6953,- 6955,6962, 6965, 6971, 6973, 6975-6977, 6982-6985, 6987, 6995-6998, 7001, 7004,7007-7008, 7010, 7012, 7016, 7018, 7021-7022, 7024-7032, 7035-7036, 7041-7042,7055, 7058, 7068, 7075, 7089, 7184, 7186-7187, 7189, 7196-7197, 7202, 7204-7206,7392, 7560DJN212-223, 225, 227-248, 251TFT149-161, 163-167
3412E TGC204-205, 208, 212-213,220, 222, 225, 227-232,235-236, 238-239, 243, 247PARTS NEEDED
Qty
Part Number Description
1 1084420 GASKET-BYP CACTION REQUIRED
Disable engine from starting
If fuel inlet and fuel return lines are not capped,do so, or connect hoses together to eliminate fuel spillage.
Loosen two 7/16" bolts under bracket supporting Deutchconnector (bolt holes have slotted openings
Remove bracket and sit aside far enough to removebolts and oil tube on fuel pump housing for servo valve.
remove 11/16" fitting on oil line to housing and rotatefitting 90 degree toward inside of engine.
Remove two 7/16" bolts from servo housing.
Carefully remove top of housing, servo valve, andspring (gasket part # 1084420)
Check for debris in servo valve. If none present reassemblein reverse order. If debris present continue.
Replace top of servo housing only - do not installvalve or spring.
10. Connect 1/2" ID x 4' long hose to 90 degreefitting out of valve housing11. Use cheesecloth or suitable material to strainoil.12. Place end of hose in bucket and crank overengine long enough to wash through 1 to 2 gallons of oil. Checked strainedoil for debris - if present repeat until strained oil shows no signs ofdebris.13. Remove cover and reinstall valve and springand reassemble in reverse order. Be certain to tighten 9/16" jam nut on90 degree fitting on oil line out of servo valve housing.Note: If package does not have batteriesinstalled, using battery pack, connect + to starter solenoid battery postand -to starter motor battery post. Jumper wire from wire #25 on solenoidto battery positive post on solenoid to crank engine and check for debrisas stated above.OWNER NOTIFICATION
U.S. and Canadian owners will receive the attachedOwner Notification.SERVICE CLAIM ALLOWANCES
Caterpillar Dealer Suggested Customer Suggested
Parts Labor Hrs. Parts Labor Hrs. Parts Labor Hrs.
100% 1.0 0 0 0 0
This is a 1.0 hour job. U.S. and Canadian Dealers Only - Eligibledealers may enter a Type 2 SIMS ReportPARTS DISPOSITION
Handle the parts in accordance with your WarrantyBulletin on warranty parts handling.MAKE EVERY EFFORT