SPACER 2063476 - Caterpillar

2063476 SPACER Caterpillar parts 365B, 365B II, 365C, 365C L, 385B, 385C L

Price: query

Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA2063476
206-3476
2063476

Buy SPACER 2063476 Caterpillar genuine, new aftermarket tractor parts with delivery
EXCAVATOR,

Compatible equipment models: 2063476:

EXCAVATOR 365B 365B II 365C 365C L 385B 385C L Caterpillar

Number on catalog scheme: 44

For full view, you need register

Caterpillar parts catalog:

Caterpillar parts catalog
Product:

365B L Excavators 9PZ00001-UP (MACHINE) POWERED BY 3196 Engine

202-5456: LINES GP-BOOM » SEBP28680569

385B & 385B L Excavators CLS00001-UP (MACHINE) POWERED BY 3456 Engine

233-0857: LINES GP-BOOM » SEBP31500530
233-0857: LINES GP-BOOM » SEBP31500531
234-5736: LINES GP-BOOM » SEBP31500536
250-6025: LINES GP-BOOM » SEBP31500543

365B Series II Excavator JMB00001-UP (MACHINE) POWERED BY 3196 Engine

233-0857: LINES GP-BOOM » SEBP37170513
233-0857: LINES GP-BOOM » SEBP37170514
250-6025: LINES GP-BOOM » SEBP37170519

365C L Excavator MEM00001-UP (MACHINE) POWERED BY C-15 Engine

266-3466: LINES GP-BOOM » SEBP42890604
266-3466: LINES GP-BOOM » SEBP42890605
266-3466: LINES GP-BOOM » SEBP42890606

385C L Excavator T2E00001-UP (MACHINE) POWERED BY C-18 Engine

234-5736: LINES GP-BOOM » SEBP42930655
266-3527: LINES GP-BOOM » SEBP42930663
266-3527: LINES GP-BOOM » SEBP42930664

385C & 385C L Excavator KGB00001-UP (MACHINE) POWERED BY C18 Engine

234-5736: LINES GP-BOOM » SEBP42980892
266-3527: LINES GP-BOOM » SEBP42980901
266-3527: LINES GP-BOOM » SEBP42980902

365C L Excavator MCY00001-UP (MACHINE) POWERED BY C-15 Engine

266-3466: LINES GP-BOOM » SEBP45120753
266-3466: LINES GP-BOOM » SEBP45120754
266-3466: LINES GP-BOOM » SEBP45120755

Information:

Illustration 1 g00388209
Schematic for the Detent CoilTilt Lever (Tilt Back)This fault is recorded when the ECM detects an incomplete electrical path from the ECM to the detent coil back to the ECM. Note: The following test procedure may create other faults. Ignore these created faults and clear the faults when the original fault is corrected. Note: All return lines for the detent coil connect to contacts J1-7 and J2-3 (wire H716-WH) of the implement ECM.
CHECK DETENT COIL
Turn the disconnect switch and the key start switch to the ON position.
Put the ECM in service mode with the same fault on hold.
Ensure that the fault present indicator is ON.
Disconnect the detent coil with the fault from the machine harness.
Observe the ON/OFF status of the fault present indicator.
At the harness connector for the detent coil, place a jumper wire between contact 1 (wire H720-BU) and contact 2 (wire H716-WH). Expected Result: The fault present indicator remains ON.Results:
YES - The fault present indicator remains ON. This indicates that a fault remains present. The machine harness is faulty or the ECM is faulty. Proceed to Step 2.
NO - The fault present indicator changes from ON to OFF. The detent coil has failed or the connecting harness has failed. Repeat this test in order to verify the failure. Repair the detent coil or replace the detent coil. Repair the connecting harness or replace the connecting harness.
CHECK FOR OPEN HARNESS CIRCUIT
Turn the disconnect switch to the OFF position.
Remove the jumper wire from contact 1 to 2.
Reconnect the detent coil to the machine harness.
Disconnect the machine harness from the ECM.
At the machine harness connector for the ECM, measure the resistance between contacts J2-3, J1-7 (wire H716-WH) and contact J2-37 (wire H720-BU). Note: The approximate resistance for a detent coil is 50.6 to 56.0 Ohms.Expected Result: The resistance is greater than 5000 Ohms with no continuity.Results:
YES - Resistance is greater than 5000 Ohms (no continuity). The harness circuit is faulty. Wire H716-WH is open in the machine harness between the ECM and the detent coil, or the wire to the detent coil is open. Repair the machine harness or replace the machine harness. STOP.
NO - Resistance is from 50.6 to 56.0 Ohms for detent coils. The harness circuit resistance is correct. It is unlikely that the ECM is faulty. Exit this procedure. Perform this CID procedure again. Also recheck if the fault present indicator is ON for this fault. If the cause is not found, replace the ECM. See Testing and Adjusting, "Electronic Control Module (ECM) - Replace". STOP.