4C1335 SPACER Caterpillar parts
824C, 980C, 980F, 980F II, AD40, AE40, R1700 II
Rating:
Alternative (cross code) number:
CA4C1335
4C-1335
4C1335
CA4C1335
4C-1335
4C1335
Weight: 0.30 pounds 0 kg.
LOAD HAUL DUMP, WHEEL LOADER,
Related part:
4C1335
WASHER-FDR-YM
3994425
CL
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
Compatible equipment models: 4C1335:
Information:
Prime the fuel system in order to fill dry fuel filters and purge air from the fuel system. Prime the fuel system after the following occurrences:
Running the fuel system dry
Removal of the engine from storage
Maintenance of the fuel filter
Disconnecting fuel lines and installing fuel lines
Repair of leaks in the fuel lines
Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire. To help prevent possible injury, turn the start switch off when changing fuel filters or water separator elements. Clean up fuel spills immediately.
Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel system component that will be disconnected. Fit a suitable cover over disconnected fuel system component.
Unlock and operate the priming pump plunger until a resistance is felt. This may require a considerable number of strokes.
Push in and hand tighten the priming pump plunger.
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Start the engine. The engine may run rough. Run the engine at low idle until the engine runs smoothly. If the following conditions exist, repeat Steps 1 through 3:
The engine will not start.
The engine starts but the engine continues to misfire.
The engine starts but the engine continues to smoke.If operating problems persist after repeating Steps 1 through 3, proceed to Step 4.
Illustration 1 g00502366
(1) Vent plug
(2) Fuel injection pump housing
Use a suitable container to catch any fuel that might spill. Clean up any spilled fuel immediately.
Loosen vent plug (1) on fuel injection pump housing (2).
Unlock and operate the priming pump plunger until the flow of fuel from the vent valve is continuous and free of air bubbles.
Tighten the vent plug. Clean up any spilled fuel immediately.
Push in and hand tighten the priming pump plunger.
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Start the engine. The engine may run rough. Run the engine at low idle until the engine runs smoothly. Proceed to Step 9 if the following conditions exist:
The engine will not start.
The engine starts but the engine continues to misfire.
The engine starts but the engine continues to smoke.
Illustration 2 g00496813
Do not let the tops of fuel nozzles turn when the fuel line nuts are loosened or tightened.The nozzles will be damaged if the top of the nozzle turns in the body.The engine will be damaged if a defective fuel injection nozzle is used because the shape of fuel (spray pattern) that comes out of the nozzles will not be correct.
Use a suitable container to catch any fuel that might spill. Clean up any spilled fuel immediately.
Loosen one fuel injection line nut at the fuel injection nozzle.
Unlock and operate the priming pump plunger until the flow of fuel from the fuel injection line is continuous and free of air bubbles.
Tighten the fuel injection line nut. Refer to Specifications for the proper torque. Clean up any spilled fuel
Running the fuel system dry
Removal of the engine from storage
Maintenance of the fuel filter
Disconnecting fuel lines and installing fuel lines
Repair of leaks in the fuel lines
Fuel leaked or spilled onto hot surfaces or electrical components can cause a fire. To help prevent possible injury, turn the start switch off when changing fuel filters or water separator elements. Clean up fuel spills immediately.
Do not allow dirt to enter the fuel system. Thoroughly clean the area around a fuel system component that will be disconnected. Fit a suitable cover over disconnected fuel system component.
Unlock and operate the priming pump plunger until a resistance is felt. This may require a considerable number of strokes.
Push in and hand tighten the priming pump plunger.
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Start the engine. The engine may run rough. Run the engine at low idle until the engine runs smoothly. If the following conditions exist, repeat Steps 1 through 3:
The engine will not start.
The engine starts but the engine continues to misfire.
The engine starts but the engine continues to smoke.If operating problems persist after repeating Steps 1 through 3, proceed to Step 4.
Illustration 1 g00502366
(1) Vent plug
(2) Fuel injection pump housing
Use a suitable container to catch any fuel that might spill. Clean up any spilled fuel immediately.
Loosen vent plug (1) on fuel injection pump housing (2).
Unlock and operate the priming pump plunger until the flow of fuel from the vent valve is continuous and free of air bubbles.
Tighten the vent plug. Clean up any spilled fuel immediately.
Push in and hand tighten the priming pump plunger.
Do not crank the engine continuously for more than 30 seconds. Allow the starting motor to cool for two minutes before cranking the engine again.
Start the engine. The engine may run rough. Run the engine at low idle until the engine runs smoothly. Proceed to Step 9 if the following conditions exist:
The engine will not start.
The engine starts but the engine continues to misfire.
The engine starts but the engine continues to smoke.
Illustration 2 g00496813
Do not let the tops of fuel nozzles turn when the fuel line nuts are loosened or tightened.The nozzles will be damaged if the top of the nozzle turns in the body.The engine will be damaged if a defective fuel injection nozzle is used because the shape of fuel (spray pattern) that comes out of the nozzles will not be correct.
Use a suitable container to catch any fuel that might spill. Clean up any spilled fuel immediately.
Loosen one fuel injection line nut at the fuel injection nozzle.
Unlock and operate the priming pump plunger until the flow of fuel from the fuel injection line is continuous and free of air bubbles.
Tighten the fuel injection line nut. Refer to Specifications for the proper torque. Clean up any spilled fuel
Caterpillar parts catalog:
Parts spacer Caterpillar catalog:
6T5611
SPACER
621E, 621F, 621G, 621H, 621K, 623E, 623F, 623G, 623H, 623K, 623K LRC, 627E, 627F, 627G, 627H, 627K, 627K LRC, 631E, 631G, 633E II, 637E, 637G, 651E, 657E, 657G, 69D, 769C, 769D, 770, 771C, 771D, 772, ...
621E, 621F, 621G, 621H, 621K, 623E, 623F, 623G, 623H, 623K, 623K LRC, 627E, 627F, 627G, 627H, 627K, 627K LRC, 631E, 631G, 633E II, 637E, 637G, 651E, 657E, 657G, 69D, 769C, 769D, 770, 771C, 771D, 772, ...
3V7729
SPACER
936F, 938F, 938G, 950F II, 960F, 966D, 966F II, 970F, 980C, 980F, 980F II, 980G, 980G II, 980H, AD30, AD45B, AD55, AD55B, AD60, AE40, IT38F
936F, 938F, 938G, 950F II, 960F, 966D, 966F II, 970F, 980C, 980F, 980F II, 980G, 980G II, 980H, AD30, AD45B, AD55, AD55B, AD60, AE40, IT38F
9K0803
SPACER
834B, 834G, 834H, 834K, 836, 836G, 836H, 836K, 986H, 988B, 988F, 988F II, 988G, 988H, 988K, AD40, AD45, AD45B, AD55, AD55B, AD60, AE40, AE40 II, R2900, R2900G, R3000H
834B, 834G, 834H, 834K, 836, 836G, 836H, 836K, 986H, 988B, 988F, 988F II, 988G, 988H, 988K, AD40, AD45, AD45B, AD55, AD55B, AD60, AE40, AE40 II, R2900, R2900G, R3000H
5N4883
SPACER
824C, 980C, 980F, D35C, D40D, D44B, D550B
824C, 980C, 980F, D35C, D40D, D44B, D550B
8V6293
SPACER
824C, 980C, AD40, AE40, D35C, D40D
824C, 980C, AD40, AE40, D35C, D40D
4D3479
SPACER
824C, 980, 980B, 980C, D35C, D40D, D44B, D550B
824C, 980, 980B, 980C, D35C, D40D, D44B, D550B
8V6384
SPACER AS
824C, 980C, 980F, 980F II, AD40, AE40, D40D, R1700 II
824C, 980C, 980F, 980F II, AD40, AE40, D40D, R1700 II
5K3491
SPACER-SPECIAL
16G, 16H, 16H NA, 16M, 824C, 824G, 824G II, 824H, 825G, 825G II, 825H, 826C, 826G, 826G II, 826H, 980, 980B, 980C, 980F, 980G, 980G II, 980H, 980K, 980K HLG, 980M, 982M, AD30, R1300, R1300G, R1300G II
16G, 16H, 16H NA, 16M, 824C, 824G, 824G II, 824H, 825G, 825G II, 825H, 826C, 826G, 826G II, 826H, 980, 980B, 980C, 980F, 980G, 980G II, 980H, 980K, 980K HLG, 980M, 982M, AD30, R1300, R1300G, R1300G II
5K3490
SPACER
16G, 16H, 16H NA, 16M, 824G, 824G II, 824H, 825G, 825G II, 825H, 826C, 826G, 826G II, 826H, 980, 980B, 980C, 980F, 980G, 980G II, 980H, 980K, 980K HLG, AD30, R1300, R1300G, R1300G II, R1600, R1600G, R...
16G, 16H, 16H NA, 16M, 824G, 824G II, 824H, 825G, 825G II, 825H, 826C, 826G, 826G II, 826H, 980, 980B, 980C, 980F, 980G, 980G II, 980H, 980K, 980K HLG, AD30, R1300, R1300G, R1300G II, R1600, R1600G, R...
9K0802
SPACER
834B, 988B, AD40, AD45, AE40, AE40 II, R2900, R2900G, R3000H
834B, 988B, AD40, AD45, AE40, AE40 II, R2900, R2900G, R3000H
7D2955
SPACER
770, 772, 773, 773B, 773D, 773E, 773F, 773G, 773G LRC, 775B, 775D, 775E, 775F, 775G, 775G LRC, AD40, AD45, AD55, AD55B, AD60
770, 772, 773, 773B, 773D, 773E, 773F, 773G, 773G LRC, 775B, 775D, 775E, 775F, 775G, 775G LRC, AD40, AD45, AD55, AD55B, AD60
1868376
SPACER
R1600, R1600G, R1600H, R1700 II, R1700G
R1600, R1600G, R1600H, R1700 II, R1700G
8V6384
SPACER AS
824C, 980C, 980F, 980F II, AD40, AE40, D40D, R1700 II
824C, 980C, 980F, 980F II, AD40, AE40, D40D, R1700 II
4D3479
SPACER
824C, 980, 980B, 980C, D35C, D40D, D44B, D550B
824C, 980, 980B, 980C, D35C, D40D, D44B, D550B
8V6293
SPACER
824C, 980C, AD40, AE40, D35C, D40D
824C, 980C, AD40, AE40, D35C, D40D
5N4883
SPACER
824C, 980C, 980F, D35C, D40D, D44B, D550B
824C, 980C, 980F, D35C, D40D, D44B, D550B
1V7749
SPACER
834B, 836, 988B
834B, 836, 988B
4V1076
SPACER
988B, 988F, 988F II
988B, 988F, 988F II
6I4225
SPACER
789C, 789D, 793C, 797, 797B, 797F, 994, 994D, 994F, 994H
789C, 789D, 793C, 797, 797B, 797F, 994, 994D, 994F, 994H
7E2456
SPACER
784B, 785, 785B, 789B, 793, 793B, 994, 994D, AD45B, AD55
784B, 785, 785B, 789B, 793, 793B, 994, 994D, AD45B, AD55
6E0743
SPACER
950B, 950F, 966D, 966F, 966F II, 980C, 980F, 988F, 988F II, 992D
950B, 950F, 966D, 966F, 966F II, 980C, 980F, 988F, 988F II, 992D
4V7029
SPACER
980C, 980F, 980F II
980C, 980F, 980F II
5K3490
SPACER
16G, 16H, 16H NA, 16M, 824G, 824G II, 824H, 825G, 825G II, 825H, 826C, 826G, 826G II, 826H, 980, 980B, 980C, 980F, 980G, 980G II, 980H, 980K, 980K HLG, AD30, R1300, R1300G, R1300G II, R1600, R1600G, R...
16G, 16H, 16H NA, 16M, 824G, 824G II, 824H, 825G, 825G II, 825H, 826C, 826G, 826G II, 826H, 980, 980B, 980C, 980F, 980G, 980G II, 980H, 980K, 980K HLG, AD30, R1300, R1300G, R1300G II, R1600, R1600G, R...
5K3491
SPACER-SPECIAL
16G, 16H, 16H NA, 16M, 824C, 824G, 824G II, 824H, 825G, 825G II, 825H, 826C, 826G, 826G II, 826H, 980, 980B, 980C, 980F, 980G, 980G II, 980H, 980K, 980K HLG, 980M, 982M, AD30, R1300, R1300G, R1300G II
16G, 16H, 16H NA, 16M, 824C, 824G, 824G II, 824H, 825G, 825G II, 825H, 826C, 826G, 826G II, 826H, 980, 980B, 980C, 980F, 980G, 980G II, 980H, 980K, 980K HLG, 980M, 982M, AD30, R1300, R1300G, R1300G II