4P3874 SPACER Caterpillar parts
245D, 375, 375 L, 5080, 578, 583R, 587R, 589, D8N, D8R, D8R II, D9N
Rating:
Alternative (cross code) number:
CA4P3874
4P-3874
4P3874
CA4P3874
4P-3874
4P3874
Weight: 1 pounds 0 kg.
EXCAVATOR, TRACK-TYPE TRACTOR,
Compatible equipment models: 4P3874:
Information:
test step.Test Step 5. CHECK THE AIR SHUTOFF SOLENOID.
Check the engine starting system. Check the fuel system. In order to check the fuel control solenoid, see Testing And Adjusting, "CID 566 FMI 7 Unexpected Shutdown Improper Mechanical Response - Test". Check for a fault with the engine starting system or the fuel system.Expected Result:The air shutoff solenoid is working properly.Results:
OK - The air shutoff solenoid is working properly. Proceed to Test Step 6.
NOT OK - The air shutoff solenoid is NOT working properly.Repair: Correct the problem with the air shutoff solenoid. Reset the genset. Operate the genset and verify that the problem has been corrected.STOPTest Step 6. CHECK THE FUSES.
Check the fuses "F2" and "F4" on the relay module.Expected Result:The fuse is NOT blown.Results:
OK - The fuse is NOT blown. Proceed to Test Step 7.
NOT OK - The fuse is blown. Proceed to Test Step 15.Test Step 7. CHECK THE SETPOINTS.
View the setpoints P017 (total cycle crank time) and P018 (cycle crank time). Make a note of the setpoints. See System Operation, "Engine/Generator Setpoint Viewing OP2-0". Compare the setpoints against the default setpoints of the particular generator set.Expected Result:The setpoints are correct. The factory default values are 90 seconds for P017 and 10 seconds for P018. Engines that are equipped with prelube pumps may require cycle crank times (setpoint P018) of 30 seconds or more.Results:
OK - The setpoints are correct. Proceed to Test Step 8.
NOT OK - The setpoints are NOT correct.Repair: Reprogram the setpoints. Reset the genset. Operate the genset and verify that the problem has been corrected.STOPTest Step 8. CHECK THE BATTERY VOLTAGE.
The engine should be off.
Measure the system voltage at the battery.Expected Result:For 24 volt systems, the voltage should be from 24.8 to 29.5 DCV. For 32 volt systems, the voltage should be from 33.1 to 39.3 DCV.Results:
OK - The voltage is correct. Proceed to Test Step 9.
NOT OK - The battery voltage is NOT within specifications.Repair: Further testing of the battery system is necessary. See Testing And Adjusting, "CID 168 Electrical System". STOPTest Step 9. CHECK THE ENGINE STARTING FUNCTION.Note: The GSC+ is attempting to crank whenever the K4 indicator is ON. The K4 indicator is located on the lower display. Be aware of the 10 second crank cycle (set by P018)that is factory set. Be sure that the K4 indicator is ON while you are making the following measurements. More than one start may be required to complete this test.
Disconnect the "B+" wire on the pinion solenoid of the starting motor. Do not allow the "B+" wire connection to contact the frame or other metal components. The "B+" wire remains disconnected for all of the remaining steps of this procedure.
Turn the engine control switch (ECS) to OFF/RESET and then turn the switch to START.
Measure the voltage from the B+ Pinion Solenoid wire (currently disconnected from the starting motor) to "B-" (ground) while the K4 indicator is ON.Expected Result:The voltage should be within
Check the engine starting system. Check the fuel system. In order to check the fuel control solenoid, see Testing And Adjusting, "CID 566 FMI 7 Unexpected Shutdown Improper Mechanical Response - Test". Check for a fault with the engine starting system or the fuel system.Expected Result:The air shutoff solenoid is working properly.Results:
OK - The air shutoff solenoid is working properly. Proceed to Test Step 6.
NOT OK - The air shutoff solenoid is NOT working properly.Repair: Correct the problem with the air shutoff solenoid. Reset the genset. Operate the genset and verify that the problem has been corrected.STOPTest Step 6. CHECK THE FUSES.
Check the fuses "F2" and "F4" on the relay module.Expected Result:The fuse is NOT blown.Results:
OK - The fuse is NOT blown. Proceed to Test Step 7.
NOT OK - The fuse is blown. Proceed to Test Step 15.Test Step 7. CHECK THE SETPOINTS.
View the setpoints P017 (total cycle crank time) and P018 (cycle crank time). Make a note of the setpoints. See System Operation, "Engine/Generator Setpoint Viewing OP2-0". Compare the setpoints against the default setpoints of the particular generator set.Expected Result:The setpoints are correct. The factory default values are 90 seconds for P017 and 10 seconds for P018. Engines that are equipped with prelube pumps may require cycle crank times (setpoint P018) of 30 seconds or more.Results:
OK - The setpoints are correct. Proceed to Test Step 8.
NOT OK - The setpoints are NOT correct.Repair: Reprogram the setpoints. Reset the genset. Operate the genset and verify that the problem has been corrected.STOPTest Step 8. CHECK THE BATTERY VOLTAGE.
The engine should be off.
Measure the system voltage at the battery.Expected Result:For 24 volt systems, the voltage should be from 24.8 to 29.5 DCV. For 32 volt systems, the voltage should be from 33.1 to 39.3 DCV.Results:
OK - The voltage is correct. Proceed to Test Step 9.
NOT OK - The battery voltage is NOT within specifications.Repair: Further testing of the battery system is necessary. See Testing And Adjusting, "CID 168 Electrical System". STOPTest Step 9. CHECK THE ENGINE STARTING FUNCTION.Note: The GSC+ is attempting to crank whenever the K4 indicator is ON. The K4 indicator is located on the lower display. Be aware of the 10 second crank cycle (set by P018)that is factory set. Be sure that the K4 indicator is ON while you are making the following measurements. More than one start may be required to complete this test.
Disconnect the "B+" wire on the pinion solenoid of the starting motor. Do not allow the "B+" wire connection to contact the frame or other metal components. The "B+" wire remains disconnected for all of the remaining steps of this procedure.
Turn the engine control switch (ECS) to OFF/RESET and then turn the switch to START.
Measure the voltage from the B+ Pinion Solenoid wire (currently disconnected from the starting motor) to "B-" (ground) while the K4 indicator is ON.Expected Result:The voltage should be within
Caterpillar parts catalog:
Parts spacer Caterpillar catalog:
1774937
SPACER
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 143H, 14H, 14H NA, 14M, 160H, 160H ES, 160H...
120H, 120H ES, 120H NA, 120K, 120K 2, 120M, 120M 2, 12H, 12H ES, 12H NA, 12K, 12M, 12M 2, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 140M, 140M 2, 143H, 14H, 14H NA, 14M, 160H, 160H ES, 160H...
1662287
SPACER
D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D8R, D8R II, D8T
D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D8R, D8R II, D8T
9P4057
SPACER
589, D10N, D10R, D10T, D10T2, D8L, D9L, D9N, D9R
589, D10N, D10R, D10T, D10T2, D8L, D9L, D9N, D9R
7M1396
SPACER
120G, 12G, 130G, 140G, 14E, 14G, 14H, 14H NA, 160G, 16G, 16H, 16H NA, 518, 518C, 528, 528B, 530B, 578, 589, 613, 613B, 814, 824, 910, 920, 930, 931, 931B, 931C, 941, 943, 950, 951B, 953, 953C, 955H, 9...
120G, 12G, 130G, 140G, 14E, 14G, 14H, 14H NA, 160G, 16G, 16H, 16H NA, 518, 518C, 528, 528B, 530B, 578, 589, 613, 613B, 814, 824, 910, 920, 930, 931, 931B, 931C, 941, 943, 950, 951B, 953, 953C, 955H, 9...
9S1385
SPACER
120B, 173B, 183B, 561D, 571G, 572G, 578, 583K, 583R, 587R, 589, 594, 594H, 651E, 657E, D10, D10N, D11N, D4E, D5B, D6D, D6G2 LGP, D6G2 XL, D6H, D6H XL, D6H XR, D7F, D7G, D7H, D8H, D8K, D8L, D8N, D9G, D...
120B, 173B, 183B, 561D, 571G, 572G, 578, 583K, 583R, 587R, 589, 594, 594H, 651E, 657E, D10, D10N, D11N, D4E, D5B, D6D, D6G2 LGP, D6G2 XL, D6H, D6H XL, D6H XR, D7F, D7G, D7H, D8H, D8K, D8L, D8N, D9G, D...
2M7167
SPACER
14E, 16, 173B, 183B, 561D, 571G, 572G, 578, 583K, 583R, 587R, 589, 594, 594H, 769, 955H, 977H, 977K, 983, D10, D10N, D11N, D4E, D5, D5B, D6C, D6D, D6E, D6G, D6G2 LGP, D6G2 XL, D6H, D6H XL, D6H XR, D7F...
14E, 16, 173B, 183B, 561D, 571G, 572G, 578, 583K, 583R, 587R, 589, 594, 594H, 769, 955H, 977H, 977K, 983, D10, D10N, D11N, D4E, D5, D5B, D6C, D6D, D6E, D6G, D6G2 LGP, D6G2 XL, D6H, D6H XL, D6H XR, D7F...
9W3937
SPACER
D5R LGP, D6H, D6H II, D6H XL, D6H XR, D6N, D6N LGP, D6N OEM, D6R, D6R II, D6R III, D7H, D7R, D7R II, D8N, D8R, D8R II
D5R LGP, D6H, D6H II, D6H XL, D6H XR, D6N, D6N LGP, D6N OEM, D6R, D6R II, D6R III, D7H, D7R, D7R II, D8N, D8R, D8R II
1196117
SPACER
5130, 5130B, 5230, 623E, 623F, 988F, 988F II, D11R, D6H, D6H XL, D6H XR, D6R, D7H, D7R, D8N, D8R, D9R
5130, 5130B, 5230, 623E, 623F, 988F, 988F II, D11R, D6H, D6H XL, D6H XR, D6R, D7H, D7R, D8N, D8R, D9R
3T5294
SPACER
572R, 572R II, D7H, D7R, D7R II, D7R XR, D8N, D8R, D8R II, D8T
572R, 572R II, D7H, D7R, D7R II, D7R XR, D8N, D8R, D8R II, D8T
7Y1493
SPACER
330, 330 FM L, 330 L, 330C, 330D L, 330D MH, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 350, 365B, 36...
330, 330 FM L, 330 L, 330C, 330D L, 330D MH, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 350, 365B, 36...
7Y4257
SPACER
322, 322 FM L, 322 LN, 322B L, 322B LN, 325, 325 L, 325 LN, 325B, 325B L, 330, 330 FM L, 330 L, 330B, 330B L, 350, 375, 375 L, 5080, E240C, E300B, EL240B, M325B, TK1051, W330B
322, 322 FM L, 322 LN, 322B L, 322B LN, 325, 325 L, 325 LN, 325B, 325B L, 330, 330 FM L, 330 L, 330B, 330B L, 350, 375, 375 L, 5080, E240C, E300B, EL240B, M325B, TK1051, W330B
7Y4258
SPACER
322, 322 FM L, 322 LN, 322B L, 322B LN, 325, 325 L, 325 LN, 325B, 325B L, 330, 330 FM L, 330 L, 330B, 330B L, 350, 375, 375 L, 5080, E240C, E300B, EL240B, M325B, TK1051, W330B
322, 322 FM L, 322 LN, 322B L, 322B LN, 325, 325 L, 325 LN, 325B, 325B L, 330, 330 FM L, 330 L, 330B, 330B L, 350, 375, 375 L, 5080, E240C, E300B, EL240B, M325B, TK1051, W330B
9Y7889
SPACER
245D, 375, 375 L, 5080, 578, 583R, 587R, 589, D8N, D8R, D8R II, D9N
245D, 375, 375 L, 5080, 578, 583R, 587R, 589, D8N, D8R, D8R II, D9N
4P6840
SPACER
224
224
7W4814
SPACER
224
224
9T7716
SPACER
235C, 235D, 245B, 554, D6H, D6H XL, D6H XR, D6R
235C, 235D, 245B, 554, D6H, D6H XL, D6H XR, D6R
9T7714
SPACER
235C, 235D, 245B, D6H, D6H XL, D6H XR, D6R
235C, 235D, 245B, D6H, D6H XL, D6H XR, D6R
6E1703
SPACER
229D, 231D, 5130, 844, 854G, 990, 990 II, 992G
229D, 231D, 5130, 844, 854G, 990, 990 II, 992G
7E5252
SPACER
215D
215D
7T8361
SPACER
225D, D6H, D6H XL, D6H XR, D6R, D6R II, D7H, D7R, D7R II, D8N, D8R, D8R II
225D, D6H, D6H XL, D6H XR, D6R, D6R II, D7H, D7R, D7R II, D8N, D8R, D8R II
6C5533
SPACER
235C
235C
4J8820
SPACER
235D, 953, D10R, D10T
235D, 953, D10R, D10T
6E4915
SPACER
235D, 245B, 245D, 990, 990 II
235D, 245B, 245D, 990, 990 II
9V4460
SPACER
245D, 315C, 315D L, 936, D3C III, D3G, D3K XL, D4C III, D4G, D4K XL, D5C III, D5G, D5K LGP
245D, 315C, 315D L, 936, D3C III, D3G, D3K XL, D4C III, D4G, D4K XL, D5C III, D5G, D5K LGP