7Y0795 SPACER Caterpillar parts
365B, 365B II, 365C, 365C L, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5080, 5090B
Rating:
Alternative (cross code) number:
CA7Y0795
7Y-0795
7Y0795
CA7Y0795
7Y-0795
7Y0795
Weight: 0.45 pounds 0 kg.
Information:
ID
115
mm
MATERIAL
Plastic
RADIAL HEIGHT
15.05
mm
CS<br>STYLE
Rect Rd
AXIAL WIDTH
25.5
EXCAVATOR, MOBILE HYD POWER UNIT,
This part in 2 request:
Show.
This information for suppliers only!
2023-11-21
2023-10-18
Compatible equipment models: 7Y0795:
Number on catalog scheme:
50
For full view, you need register
Information:
Cylinder Block
The cylinder block is a unique design with a deep counterbore that supports the cylinder liner. The cylinder block also forms the coolant jacket. Two oil manifolds are provided in the cylinder block for engine lubrication. The manifold on the lower right side of the cylinder block provides oil to the following components:
Piston cooling jets
Crankshaft bearings
Oil filter baseThe manifold on the upper left side of the cylinder block provides oil to the following components:
Camshaft bearings
Valve mechanismThe manifold on the right supplies oil to the manifold on the left. The oil travels through the cut above the number one main bearing and the cut above the number four main bearing.
Illustration 1 g01099436Cylinder liners (1) are seated on a ridge (4) in the middle of the cylinder wall between the crankcase and the coolant jacket. The ridge is created by a counterbore in the cylinder block. The cylinder liners have a lip (2) which rests on the ridge. The seals of the coolant jacket are located in the upper regions and middle regions of the cylinder liners. The lower barrier uses a D-ring seal (3) that is located above the seating surface of the cylinder liner. The upper barrier is the head gasket which is above the coolant jacket.The cylinder block has seven main bearings in order to support the crankshaft. Each main bearing cap is fastened to the cylinder block with two bolts.Pistons, Rings, and Connecting Rods
The high compression ratio of the engine requires the use of a piston that is made of steel.The pistons have three rings:
Compression ring
Intermediate ring
Oil ringThe rings are located in grooves in the piston. The rings seal the crankcase from the combustion gases and the rings also provide control of the engine oil. The design of the compression ring is a barrel face with a plasma face coating. The design of the intermediate ring is a tapered shape and a chrome finish. The oil ring is double railed with a coil spring expander. The oil ring has a ground profile and a chrome finish.The connecting rod is a conventional design. The cap is fastened to the shank by two bolts that are threaded into the shank. Each side of the small end of the connecting rod is machined at an angle of 12 degrees in order to fit within the piston cavity. This allows a larger surface area on the piston, and connecting rod in order to minimize bearing load.Crankshaft
The crankshaft converts the linear motion of the pistons into rotational motion. The crankshaft drives a group of gears (front gear train) on the front of the engine. The front gear train provides power for the following components:
Camshaft
Water pump
Engine oil pump
Air compressor
Fuel transfer pump
Accessory driveThe crankshaft is held in place by seven main bearings. The oil holes and the oil grooves in the shell of the upper bearing supply oil to the connecting rod bearings. The oil holes for the connecting rod bearings are located at the following main bearing journals: 2, 3, 5 and
The cylinder block is a unique design with a deep counterbore that supports the cylinder liner. The cylinder block also forms the coolant jacket. Two oil manifolds are provided in the cylinder block for engine lubrication. The manifold on the lower right side of the cylinder block provides oil to the following components:
Piston cooling jets
Crankshaft bearings
Oil filter baseThe manifold on the upper left side of the cylinder block provides oil to the following components:
Camshaft bearings
Valve mechanismThe manifold on the right supplies oil to the manifold on the left. The oil travels through the cut above the number one main bearing and the cut above the number four main bearing.
Illustration 1 g01099436Cylinder liners (1) are seated on a ridge (4) in the middle of the cylinder wall between the crankcase and the coolant jacket. The ridge is created by a counterbore in the cylinder block. The cylinder liners have a lip (2) which rests on the ridge. The seals of the coolant jacket are located in the upper regions and middle regions of the cylinder liners. The lower barrier uses a D-ring seal (3) that is located above the seating surface of the cylinder liner. The upper barrier is the head gasket which is above the coolant jacket.The cylinder block has seven main bearings in order to support the crankshaft. Each main bearing cap is fastened to the cylinder block with two bolts.Pistons, Rings, and Connecting Rods
The high compression ratio of the engine requires the use of a piston that is made of steel.The pistons have three rings:
Compression ring
Intermediate ring
Oil ringThe rings are located in grooves in the piston. The rings seal the crankcase from the combustion gases and the rings also provide control of the engine oil. The design of the compression ring is a barrel face with a plasma face coating. The design of the intermediate ring is a tapered shape and a chrome finish. The oil ring is double railed with a coil spring expander. The oil ring has a ground profile and a chrome finish.The connecting rod is a conventional design. The cap is fastened to the shank by two bolts that are threaded into the shank. Each side of the small end of the connecting rod is machined at an angle of 12 degrees in order to fit within the piston cavity. This allows a larger surface area on the piston, and connecting rod in order to minimize bearing load.Crankshaft
The crankshaft converts the linear motion of the pistons into rotational motion. The crankshaft drives a group of gears (front gear train) on the front of the engine. The front gear train provides power for the following components:
Camshaft
Water pump
Engine oil pump
Air compressor
Fuel transfer pump
Accessory driveThe crankshaft is held in place by seven main bearings. The oil holes and the oil grooves in the shell of the upper bearing supply oil to the connecting rod bearings. The oil holes for the connecting rod bearings are located at the following main bearing journals: 2, 3, 5 and
Cat SIS web machinery list:
Parts spacer Caterpillar catalog:
307B, 307C, 324D, 325C, 325D L, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E L, 336E LN, 340D L, 340D2 L, 345B II,...
305.5, 306, 307C, 307D, 325, 325 L, 325 LN, 330, 330 FM L, 330 L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 374D L, 374F L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 39...
315C, 315D L, 318C, 319C, 319D, 319D LN, 320 L, 320B, 320B FM LL, 320B L, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, 320D2 L, 320E,...
312C, 312D, 312E, 312E L, 314E CR, 314E LCR, 315C, 315D L, 316E L, 318C, 318E L, 319C, 319D, 320C, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 322C, 323D L, 323D LN, 323E L, 324D, 324D L, 324D LN, 324E,...
330, 330 FM L, 330 L, 330C, 330D L, 330D MH, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 350, 365B, 36...
322, 322 FM L, 322 LN, 322B L, 322B LN, 325, 325 L, 325 LN, 325B, 325B L, 330, 330 FM L, 330 L, 330B, 330B L, 350, 375, 375 L, 5080, E240C, E300B, EL240B, M325B, TK1051, W330B
322, 322 FM L, 322 LN, 322B L, 322B LN, 325, 325 L, 325 LN, 325B, 325B L, 330, 330 FM L, 330 L, 330B, 330B L, 350, 375, 375 L, 5080, E240C, E300B, EL240B, M325B, TK1051, W330B
365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5090B
330C, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 340D L, 340D2 L, 385B, 385C, 3...
365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 374D L, 374F L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5090B
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 320C, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 324E LN, 325, 325 FM L, 325 L, 325 LN, 325B, 325B L, 325C, 325C FM, 325C ...
320B, 320C, 320C FM, 320D, 320D FM, 320D FM RR, 322 FM L, 322B L, 322B LN, 322C, 322C FM, 323D LN, 323D SA, 323E L, 324D, 324D L, 324D LN, 324E, 324E L, 324E LN, 325, 325 L, 325 LN, 325B, 325B L, 325C...
1359125
SPACER
375, 5080
375, 5080
5130, 5130B, 5230, 5230B
1146488
SPACER
5130
5130
350, 375, 375 L, 5080, 5110B, 5130, 5230
1008353
SPACER
350, 375, 375 L, 5080, 5110B, 5130, 5230
350, 375, 375 L, 5080, 5110B, 5130, 5230
6I7464
SPACER
5130, 5130B, 5230, 5230B
5130, 5130B, 5230, 5230B
1066418
SPACER
375, 5080, D8R, D8R II
375, 5080, D8R, D8R II
1035242
SPACER
350, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L MH, 5080, 5090B
350, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L MH, 5080, 5090B
350, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, 375, 375 L, 385B, 385C, 385C FS, 385C L, 385C L MH, 5080, 5090B
6I6233
SPACER
350, 350 L, 375, 375 L, 5080
350, 350 L, 375, 375 L, 5080
330, 330 FM L, 330 L, 330C, 330D L, 330D MH, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 350, 365B, 36...
365B, 375, 375 L, 5080