1366545 SPIDER Caterpillar parts
950G, 950G II, 950H, 950K, 962G, 962G II, 962H, 962K, IT62G, IT62G II, IT62H
Rating:
Alternative (cross code) number:
CA1366545
136-6545
1366545
CA1366545
136-6545
1366545
Weight: 6 pounds 2 kg.
INTEGRATED TOOLCARRIER, WHEEL LOADER,
This part in 2 request:
Show.
This information for suppliers only!
2018-02-10
2017-03-18
Compatible equipment models: 1366545:
Information:
Remove Accessory Drive Gears
start by: a) remove accessory drive housing 1. Remove bolts and locks from water pump drive gear (2). Remove gear from shaft.2. Remove oil pump drive gear (4) from its shaft.3. Remove the main idler gear (1) and its shaft. Turn the crankshaft to get bolts that hold shaft to cylinder block and plate (3).4. Remove bearings from gears (1), (2), and (4).5. On D379 only, install tooling (A) on the thrower. Put heat on the outer diameter of thrower with an open flame at a maximum temperature of 400°F (205°C). Remove the thrower immediately with tooling (A).6. Remove the balancer gear (6).7. Remove the bearing from balancer gear. 8. Remove oil tube (5) from plate. If plate is to be removed, remove oil pump and fresh water pump. Remove plate (3) from cylinder block. Check the mark on plate for correct installation. The front of plate for SAE standard rotation engine (counterclockwise as viewed from flywheel end) is marked "FRONT STD. ROT." The front of plate for SAE opposite rotation engine (clockwise as viewed from flywheel end) is marked "FRONT REV. ROT."Install Accessory Drive Gears
1. Install the plate (3) on cylinder block. Tighten five 1/2" bolts to 90 5 lb.ft. (120 7 N m). Be sure the plate is installed on correct side as indicated in removal.2. Install the oil tube (1). Install small gaskets under nuts that hold right end of tube. Put 7M7260 Liquid Gasket Material on sealing surfaces of idler gear shaft oil tube (1), and shaft for main idler gear (2). 3. On D379 engine only, install bearing in balancer gear with tooling (A). Install the balancer gear and shaft. Tighten bolts to 40 4 lb. ft. (55 5 N m).4. Install bearings in the gears for oil pump and main idler gear. The gear train of accessory drive are the same on the 8, 12, and 16 cylinder engines, except for balancer gear used on 8 cylinder engine. On SAE standard rotation (counterclockwise) engines, the balancer gear timing mark "B" must be in alignment with the tooth on crankshaft gear with punch marks (four, five or six punch marks). The balancer gear timing mark "B" must be in alignment with the "B" mark on the main idler gear.
SAE Standard Rotation 8 Cylinder Engine5. Install main idler gear and shaft. Install engine oil pump and fresh water pump. Install gears for oil pump and water pump.
SAE OPPOSITE ROTATION 8 CYLINDER ENGINE On SAE opposite rotation (clockwise) engine, the balancer gear timing mark "R" must be in alignment with the "R" on the small idler gear. The other "R" on the small idler gear must be in alignment between two teeth on crankshaft gear with two punch marks. On 12 and 16 cylinder engines, no timing of accessory drive gears is necessary. 6. On D379, heat the thrower (4) in oil to a maximum temperature of 300°F (149°C). Install the thrower (4) on crankshaft. Use tooling (B)
start by: a) remove accessory drive housing 1. Remove bolts and locks from water pump drive gear (2). Remove gear from shaft.2. Remove oil pump drive gear (4) from its shaft.3. Remove the main idler gear (1) and its shaft. Turn the crankshaft to get bolts that hold shaft to cylinder block and plate (3).4. Remove bearings from gears (1), (2), and (4).5. On D379 only, install tooling (A) on the thrower. Put heat on the outer diameter of thrower with an open flame at a maximum temperature of 400°F (205°C). Remove the thrower immediately with tooling (A).6. Remove the balancer gear (6).7. Remove the bearing from balancer gear. 8. Remove oil tube (5) from plate. If plate is to be removed, remove oil pump and fresh water pump. Remove plate (3) from cylinder block. Check the mark on plate for correct installation. The front of plate for SAE standard rotation engine (counterclockwise as viewed from flywheel end) is marked "FRONT STD. ROT." The front of plate for SAE opposite rotation engine (clockwise as viewed from flywheel end) is marked "FRONT REV. ROT."Install Accessory Drive Gears
1. Install the plate (3) on cylinder block. Tighten five 1/2" bolts to 90 5 lb.ft. (120 7 N m). Be sure the plate is installed on correct side as indicated in removal.2. Install the oil tube (1). Install small gaskets under nuts that hold right end of tube. Put 7M7260 Liquid Gasket Material on sealing surfaces of idler gear shaft oil tube (1), and shaft for main idler gear (2). 3. On D379 engine only, install bearing in balancer gear with tooling (A). Install the balancer gear and shaft. Tighten bolts to 40 4 lb. ft. (55 5 N m).4. Install bearings in the gears for oil pump and main idler gear. The gear train of accessory drive are the same on the 8, 12, and 16 cylinder engines, except for balancer gear used on 8 cylinder engine. On SAE standard rotation (counterclockwise) engines, the balancer gear timing mark "B" must be in alignment with the tooth on crankshaft gear with punch marks (four, five or six punch marks). The balancer gear timing mark "B" must be in alignment with the "B" mark on the main idler gear.
SAE Standard Rotation 8 Cylinder Engine5. Install main idler gear and shaft. Install engine oil pump and fresh water pump. Install gears for oil pump and water pump.
SAE OPPOSITE ROTATION 8 CYLINDER ENGINE On SAE opposite rotation (clockwise) engine, the balancer gear timing mark "R" must be in alignment with the "R" on the small idler gear. The other "R" on the small idler gear must be in alignment between two teeth on crankshaft gear with two punch marks. On 12 and 16 cylinder engines, no timing of accessory drive gears is necessary. 6. On D379, heat the thrower (4) in oil to a maximum temperature of 300°F (149°C). Install the thrower (4) on crankshaft. Use tooling (B)
Caterpillar parts catalog:
Parts spider Caterpillar catalog:
1258810
SPIDER & BEARING GP
950G, 950G II, 950H, 950K, 962G, 962G II, 962H, 962K, 966G, 966G II, 966H, 966K, 966M, 966M XE, 972G, 972G II, 972H, 972K, 972M, 972M XE, IT62G, IT62G II, IT62H
950G, 950G II, 950H, 950K, 962G, 962G II, 962H, 962K, 966G, 966G II, 966H, 966K, 966M, 966M XE, 972G, 972G II, 972H, 972K, 972M, 972M XE, IT62G, IT62G II, IT62H
2460616
SPIDER AS-FAN
950 GC, 950H, 950K, 962H, 962K, 966F II, D6T LGP, D6T LGPPAT, D6T XL, IT62H
950 GC, 950H, 950K, 962H, 962K, 966F II, D6T LGP, D6T LGPPAT, D6T XL, IT62H
1504988
SPIDER AS
938G, 950G, 962G, IT38G
938G, 950G, 962G, IT38G
5V1274
SPIDER
515, 525, 613B, 613C, 613C II, 613G, 725, 725C, 730, 730C, 735, 928H, 928HZ, 930G, 936, 936F, 938F, 938G, 938G II, 950B, 950B/950E, 950F, 950F II, 950G, 960F, 962G, 966C, D250B, D250E II, D25C, D300B,...
515, 525, 613B, 613C, 613C II, 613G, 725, 725C, 730, 730C, 735, 928H, 928HZ, 930G, 936, 936F, 938F, 938G, 938G II, 950B, 950B/950E, 950F, 950F II, 950G, 960F, 962G, 966C, D250B, D250E II, D25C, D300B,...
1860116
SPIDER AS-FAN
938G II, 950G II, 962G II, IT38G II, IT62G II
938G II, 950G II, 962G II, IT38G II, IT62G II
1197864
SPIDER AS-FAN
120H, 135H, 938G, 950G, 962G, IT38G, IT62G
120H, 135H, 938G, 950G, 962G, IT38G, IT62G
4E9324
SPIDER & BEARING GP
938G, 938G II, 938H, 938K, 950F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, IT38G, IT38G II, IT38H, IT62G, IT62G II, IT62H
938G, 938G II, 938H, 938K, 950F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, IT38G, IT38G II, IT38H, IT62G, IT62G II, IT62H
1197864
SPIDER AS-FAN
120H, 135H, 938G, 950G, 962G, IT38G, IT62G
120H, 135H, 938G, 950G, 962G, IT38G, IT62G
2560809
SPIDER-DRIVE
631E, 631G, 633E II, 637E, 637G
631E, 631G, 633E II, 637E, 637G
2445929
SPIDER AS-FAN
24M, 631D, 631E, 631G, 633E II, 637D, 637E, 637G, 657E, 657G, 770, 770G, 770G OEM, 772, 772G, 772G OEM
24M, 631D, 631E, 631G, 633E II, 637D, 637E, 637G, 657E, 657G, 770, 770G, 770G OEM, 772, 772G, 772G OEM
1133633
SPIDER AS-FAN
928G, IT28G
928G, IT28G
1857978
SPIDER AS-FAN
621G, 623G, 627F, 627G, 657B
621G, 623G, 627F, 627G, 657B
1344040
SPIDER AS-FAN
1090, 1190, 1190T, 1290T, 2290, 2390, 2391, 2491, 511, 521, 522, 532, 627G, 637D, 637E, 637G, TK711, TK721, TK722, TK732
1090, 1190, 1190T, 1290T, 2290, 2390, 2391, 2491, 511, 521, 522, 532, 627G, 637D, 637E, 637G, TK711, TK721, TK722, TK732
1912226
SPIDER & BEARING GP
914G, 924G, 924GZ, 924H, 924HZ, 924K, 928H, 928HZ, 930G, 930K, IT14G, IT14G2, IT28G
914G, 924G, 924GZ, 924H, 924HZ, 924K, 928H, 928HZ, 930G, 930K, IT14G, IT14G2, IT28G
1851046
SPIDER AS-FAN
924G, 924GZ, 924H, 924HZ, 928H, 928HZ, 930G, IT28G
924G, 924GZ, 924H, 924HZ, 928H, 928HZ, 930G, IT28G
1907619
SPIDER AS-FAN
631D, 631G, 637G
631D, 631G, 637G
1773321
SPIDER AS-FAN
924G, 924GZ
924G, 924GZ
4E9324
SPIDER & BEARING GP
938G, 938G II, 938H, 938K, 950F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, IT38G, IT38G II, IT38H, IT62G, IT62G II, IT62H
938G, 938G II, 938H, 938K, 950F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, IT38G, IT38G II, IT38H, IT62G, IT62G II, IT62H