1755188 SPIDER & BEARING GP Caterpillar parts
561N, D5N
Rating:
Alternative (cross code) number:
CA1755188
175-5188
1755188
CA1755188
175-5188
1755188
Weight: 3 pounds 1 kg.
PIPELAYER, TRACK-TYPE TRACTOR,
Information:
start by:a) remove pistons1. Drain the coolant from the cooling system and cylinder block.2. Put covers on the crankshaft journals for protection from dirt and coolant.3. Remove the cylinder liner with tool (A).4. Remove seals (1) and filler band (2) from the cylinder liner. INSTALL CYLINDER LINERS
1. Install the gasket and spacer plate.2. Clean the cylinder liners and liner bores in the cylinder block.3. Install the cylinder liners in the cylinder block without seals or bands.4. Check the cylinder liner projection as follows:a) Install four bolts (4) and washers from tooling (A) around each cylinder liner as shown. Tighten the bolts evenly to a torque of 95 N m (70 lb.ft.).b) Install crossbar (2), plates (3) and bolts (1) from tooling (A). Be sure the crossbar is in position at the center of the liner and the liner surface is clean. Tighten the bolts (1) evenly to a torque of 70 N m (50 lb.ft.).c) Check the distance from the bottom edge of crossbar (2) to the top edge of the spacer plate. The distance on each end of the crossbar must be the same.d) Check the liner projection with tool (B) at four locations around the liner. Liner projection must be 0.059 to 0.199 mm (.0023 to .0078 in.). The difference between the four measurements on the same liner must not be more than 0.05 mm (.002 in.). If the liner is turned in the cylinder block, it can make a difference in liner projection. 5. If the liner projection is not 0.059 to 0.199 mm (.0023 to .0078 in.), check the thickness of the following parts: a) Spacer plate (X): 10.313 0.025 mm (.4060 .0010 in.).b) Spacer plate gasket (Y): 0.208 0.025 mm (.0082 .0010 in.). [All surfaces must be clean and dry when gaskets are installed].c) Cylinder liner flange (Z): 10.65 .02 mm (.419 .001 in.).6. Put a mark on the cylinder liners and block so the liners can be installed in same position.7. Remove tooling (A) and (B). Remove the liner.8. Put liquid soap on seals (5), grooves of the liner and the bore of the block. Install the seals on the cylinder liner.9. Put the filler band completely in clean engine oil for a moment. Install filler band (6) in the groove under the liner flange without delay.10. Install the liner immediately after the filler band is installed before expansion of the band. Make sure the mark on the liner is in alignment with the mark on the block. Use tooling (C) to push the liner into position.11. Use Steps 7 through 10 for the remainder of the liners.end by:a) install pistons
1. Install the gasket and spacer plate.2. Clean the cylinder liners and liner bores in the cylinder block.3. Install the cylinder liners in the cylinder block without seals or bands.4. Check the cylinder liner projection as follows:a) Install four bolts (4) and washers from tooling (A) around each cylinder liner as shown. Tighten the bolts evenly to a torque of 95 N m (70 lb.ft.).b) Install crossbar (2), plates (3) and bolts (1) from tooling (A). Be sure the crossbar is in position at the center of the liner and the liner surface is clean. Tighten the bolts (1) evenly to a torque of 70 N m (50 lb.ft.).c) Check the distance from the bottom edge of crossbar (2) to the top edge of the spacer plate. The distance on each end of the crossbar must be the same.d) Check the liner projection with tool (B) at four locations around the liner. Liner projection must be 0.059 to 0.199 mm (.0023 to .0078 in.). The difference between the four measurements on the same liner must not be more than 0.05 mm (.002 in.). If the liner is turned in the cylinder block, it can make a difference in liner projection. 5. If the liner projection is not 0.059 to 0.199 mm (.0023 to .0078 in.), check the thickness of the following parts: a) Spacer plate (X): 10.313 0.025 mm (.4060 .0010 in.).b) Spacer plate gasket (Y): 0.208 0.025 mm (.0082 .0010 in.). [All surfaces must be clean and dry when gaskets are installed].c) Cylinder liner flange (Z): 10.65 .02 mm (.419 .001 in.).6. Put a mark on the cylinder liners and block so the liners can be installed in same position.7. Remove tooling (A) and (B). Remove the liner.8. Put liquid soap on seals (5), grooves of the liner and the bore of the block. Install the seals on the cylinder liner.9. Put the filler band completely in clean engine oil for a moment. Install filler band (6) in the groove under the liner flange without delay.10. Install the liner immediately after the filler band is installed before expansion of the band. Make sure the mark on the liner is in alignment with the mark on the block. Use tooling (C) to push the liner into position.11. Use Steps 7 through 10 for the remainder of the liners.end by:a) install pistons
Caterpillar parts catalog:
Parts spider Caterpillar catalog:
2053577
SPIDER AS-FAN
561N, D5N
561N, D5N
1874484
SPIDER AS-FAN
561N, D5N
561N, D5N
1874484
SPIDER AS-FAN
561N, D5N
561N, D5N
2053577
SPIDER AS-FAN
561N, D5N
561N, D5N
1888954
SPIDER AS-FAN
D5R LGP, D6N, D6N LGP, D6N OEM
D5R LGP, D6N, D6N LGP, D6N OEM
1898904
SPIDER AS-FAN
D6N, D6N LGP
D6N, D6N LGP
2262261
SPIDER AS-FAN
D5R LGP, D6N
D5R LGP, D6N
2460616
SPIDER AS-FAN
950 GC, 950H, 950K, 962H, 962K, 966F II, D6T LGP, D6T LGPPAT, D6T XL, IT62H
950 GC, 950H, 950K, 962H, 962K, 966F II, D6T LGP, D6T LGPPAT, D6T XL, IT62H
2617504
SPIDER AS-FAN
D6K, D6K LGP, D6K XL, D6K2, D6K2 LGP, PL61
D6K, D6K LGP, D6K XL, D6K2, D6K2 LGP, PL61
1188458
SPIDER AS-FAN
572R II, D7R, D7R II, D8R
572R II, D7R, D7R II, D8R