1976335 SPIDER AS-FAN Caterpillar parts
D8L, D9N, D9R
Rating:
Alternative (cross code) number:
CA1976335
197-6335
1976335
CA1976335
197-6335
1976335
Weight: 108 pounds 49 kg.
Information:
BLADE WIDTH
80.8
mm
BOLT CIRCLE DIAMETER
139.7
mm
DIAMETER OF PITCH CIRCLE HOLES
13.5
mm
HUB THICKNESS
7.92
mm
NUMBER OF BLADES
8
NUMBER OF PITCH HOLES
6
OD
1219.2
mm
PILOT HOLE DIAMETER
76.24
mm
TYPE
BLOWER
TRACK-TYPE TRACTOR,
Number on catalog scheme:
3
For full view, you need register
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1 Start By:
Release the hydraulic system pressure. Refer to Disassembly and Assembly, " Hydraulic System Pressure - Release".
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01258791
Install Tooling (A) onto the hydraulic tank. Attach an air supply hose onto Tooling (A). Apply 345 69 kPa (50 10 psi) of air. This procedure will pull vacuum on the hydraulic system.
Illustration 2 g01258793
Remove bolts (1). Remove sheet (2) .
Illustration 3 g01258792
Disconnect hose assembly (3). Remove nuts (5). Remove accumulator (4) .Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1 Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
Illustration 4 g01258791
Install Tooling (A) onto the hydraulic tank.
Illustration 5 g01258792
Position accumulator (4). Install nuts (5). Connect hose assembly (3).
Illustration 6 g01258793
Position sheet (2). Install bolts (1).
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1 Start By:
Release the hydraulic system pressure. Refer to Disassembly and Assembly, " Hydraulic System Pressure - Release".
Personal injury can result from hydraulic oil pressure and hot oil.Hydraulic oil pressure can remain in the hydraulic system after the engine has been stopped. Serious injury can be caused if this pressure is not released before any service is done on the hydraulic system.Make sure all of the work tools have been lowered to the ground, and the oil is cool before removing any components or lines. Remove the oil filler cap only when the engine is stopped, and the filler cap is cool enough to touch with your bare hand.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01258791
Install Tooling (A) onto the hydraulic tank. Attach an air supply hose onto Tooling (A). Apply 345 69 kPa (50 10 psi) of air. This procedure will pull vacuum on the hydraulic system.
Illustration 2 g01258793
Remove bolts (1). Remove sheet (2) .
Illustration 3 g01258792
Disconnect hose assembly (3). Remove nuts (5). Remove accumulator (4) .Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A FT-2674 Vacuum Cap 1 Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
Illustration 4 g01258791
Install Tooling (A) onto the hydraulic tank.
Illustration 5 g01258792
Position accumulator (4). Install nuts (5). Connect hose assembly (3).
Illustration 6 g01258793
Position sheet (2). Install bolts (1).
Caterpillar parts catalog:
Parts spider Caterpillar catalog:
589, D8L
8N5025
SPIDER AS-FAN
589, D8L
589, D8L
589, 69D, 769C, 769D, 770, 771C, 771D, 772, 772G, 772G OEM, AD40, AD45, AE40, AE40 II, D350E II, D8L, D9R, D9T
D9G, D9N
2047978
SPIDER AS-FAN
D8R, D8R II
D8R, D8R II
1253949
SPIDER AS-FAN
D7R, D8R, D8R II
D7R, D8R, D8R II
3727969
SPIDER AS-FAN
D7R II, D8R, D8R II
D7R II, D8R, D8R II
8N9005
SPIDER AS-FAN
D11N
D11N
1779388
SPIDER AS-FAN
D10N, D10R
D10N, D10R