2N2361 SPIDER AS-FAN Caterpillar parts
3114, 3116, 3208
Rating:
Alternative (cross code) number:
CA2N2361
2N-2361
2N2361
CA2N2361
2N-2361
2N2361
Weight: 7 pounds 3 kg.
Information:
BLADE WIDTH
53.3
mm
BOLT CIRCLE DIAMETER
69.85
mm
DIAMETER OF PITCH CIRCLE HOLES
8.6
mm
HUB THICKNESS
9.1
mm
NUMBER OF BLADES
5
NUMBER OF PITCH HOLES
4
OD
558.8
mm
PILOT HOLE DIAMETER
32.11
mm
TYPE
BLOWER
GEN SET ENGINE, INDUSTRIAL ENGINE,
Compatible equipment models: 2N2361:
Number on catalog scheme:
4
For full view, you need register
Information:
Remove And Install Crankshaft Gear
start by: a) remove crankshaft rear seal and wear sleeve 1. Turn the crankshaft so key (1) is in the location shown. 2. Install tooling (A) with drill bushing (2) in alignment with key (1).3. Install tooling (B). Hold tooling (B) in place with tape.4. Put rags around crankshaft gear so chips can not get into the engine crankcase.5. Put tape around a 9/32" (7.1 mm) carbide drill 3/4" (19.05 mm) from end of drill.6. Drill to a depth of 3/4" (19.05 mm).
Do not drill through the gear. Use cutting oil on drill while drilling.
7. Remove tooling (A) and (B).8. Use a chisel and break the gear near the key.9. Remove the crankshaft gear. 10. Heat the new gear (4) to no more than 400°F(204°C) and install the gear on the crankshaft. Before installing the gear (4) see that key (1) is in position in crankshaft.end by: a) install crankshaft gear wear sleeve.
start by: a) remove crankshaft rear seal and wear sleeve 1. Turn the crankshaft so key (1) is in the location shown. 2. Install tooling (A) with drill bushing (2) in alignment with key (1).3. Install tooling (B). Hold tooling (B) in place with tape.4. Put rags around crankshaft gear so chips can not get into the engine crankcase.5. Put tape around a 9/32" (7.1 mm) carbide drill 3/4" (19.05 mm) from end of drill.6. Drill to a depth of 3/4" (19.05 mm).
Do not drill through the gear. Use cutting oil on drill while drilling.
7. Remove tooling (A) and (B).8. Use a chisel and break the gear near the key.9. Remove the crankshaft gear. 10. Heat the new gear (4) to no more than 400°F(204°C) and install the gear on the crankshaft. Before installing the gear (4) see that key (1) is in position in crankshaft.end by: a) install crankshaft gear wear sleeve.
Caterpillar parts catalog:
Parts spider Caterpillar catalog:
3116, 3126, 3208
7W5643
SPIDER AS-FAN
3508, 3512, 3516
3508, 3512, 3516
7C4625
SPIDER AS-FAN
3126B, 3406B, 3408, C-9, C7, C9, CX31-C9I, TH31-E61
3126B, 3406B, 3408, C-9, C7, C9, CX31-C9I, TH31-E61
4N3338
SPIDER AS
3406, 3406B, 3406C, 3408, 3408C, 3408E, 3412, 3412C, 3412E, 3508, 3512, 3516, C15, C18, C27, C32, CX31-C15I, CX35-P800, D44B, D550B, G3412, TH35-C15I, TH48-E70
3406, 3406B, 3406C, 3408, 3408C, 3408E, 3412, 3412C, 3412E, 3508, 3512, 3516, C15, C18, C27, C32, CX31-C15I, CX35-P800, D44B, D550B, G3412, TH35-C15I, TH48-E70
3126B, 3176B, 3176C, 3196, 3406, 3406B, 3406C, 3406E, 3408, 3408C, 3408E, 3412, 3412C, 3412E, 350, C-10, C-12, C-15, C-16, C-9, C11, C13, C15, C18, C9, C9.3, CX31-C13I, CX31-C15I, CX31-C9I, CX35-P800,...
7C4624
SPIDER AS
3126B, 3406B, 3408, 3456, C-9, C7, C9, CX31-C9I, G3306, TH31-E61
3126B, 3406B, 3408, 3456, C-9, C7, C9, CX31-C9I, G3306, TH31-E61
3456, C15, C18, PM3456
1517795
SPIDER AS-FAN
3412C
3412C
1517796
SPIDER AS-FAN
3412C
3412C
7N4805
SPIDER AS-FAN
3408, 3408E, 3412, 3412C, 3412E, 3512, C27, C32, TH48-E70
3408, 3408E, 3412, 3412C, 3412E, 3512, C27, C32, TH48-E70
7W4462
SPIDER AS-FAN
3208
3208