8K6042 SPIDER & BEARING ASSEM. Caterpillar parts
528, D10
Rating:
Alternative (cross code) number:
CA8K6042
8K-6042
8K6042
CA8K6042
8K-6042
8K6042
Weight: 6 pounds 2 kg.
TRACK-TYPE TRACTOR, WHEEL SKIDDER,
You can buy:
US$61.94
28 May 2025
FridayParts
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CARTEX Spider & Bearing Assembly 8K6042 for FITS Caterpillar CAT 528 D10 Track Skidder D348 3306 Engine
CARTEX Whether you're a professional mechanic or a DIY enthusiast,We've got you covered with a wide range of parts that meet the highest standards of quality and performance. || Order your High Quality Part with peace of mind, knowing we prioritize your satisfaction. Quality Parts, Superior Performance - it's not just a promise, it's our standard || QUESTIONS? : We at CARTEX - High Quality Parts USA has more than 40 years of experience in industry and has in-house technicians, If you are not sure if this part fits your machine or tractor, just send us an email before you make the purchase and our in house technicians will revert back to you, right away.
CARTEX Whether you're a professional mechanic or a DIY enthusiast,We've got you covered with a wide range of parts that meet the highest standards of quality and performance. || Order your High Quality Part with peace of mind, knowing we prioritize your satisfaction. Quality Parts, Superior Performance - it's not just a promise, it's our standard || QUESTIONS? : We at CARTEX - High Quality Parts USA has more than 40 years of experience in industry and has in-house technicians, If you are not sure if this part fits your machine or tractor, just send us an email before you make the purchase and our in house technicians will revert back to you, right away.
8K6042 Spider A (New AFTERMARKET) - G&T Engine Parts
G&T Engine Parts Condition: NEW AFTERMARKET || Weight: 7.59 lbs || Related Items: 1688279, 2111046, 5766277, 8d7719, 8k6042, 9p0356 || Use of any OEM manufacturer name is not intended to represent any relationship between the two companies, instead it indicates that we sell replacement parts that are compatible with OEM components.
G&T Engine Parts Condition: NEW AFTERMARKET || Weight: 7.59 lbs || Related Items: 1688279, 2111046, 5766277, 8d7719, 8k6042, 9p0356 || Use of any OEM manufacturer name is not intended to represent any relationship between the two companies, instead it indicates that we sell replacement parts that are compatible with OEM components.
Information:
Probable Causes
Machine security system
Battery cables and/or batteries
Starting motor solenoid or starting circuit
Starting motor and/or flywheel ring gear
Electrical power supply
Internal engine faultRecommended Repairs
Machine Security System
Verify that the correct key is being used. Turn the key to the ON position.
Use the electronic service tool in order to check if diagnostic code 1639-09 is active. Verify that the lamp for the machine security system is on.
If the 1639-09 diagnostic code is active the machine security system is armed. Deactivate the machine security system and try to start the engine.
If the engine will not start use the electronic service tool to check for active diagnostic codes and logged diagnostic codes.
Investigate any active diagnostic codes and logged diagnostic codes and make all necessary repairs in order to eliminate the diagnostic codes.
If there are no active diagnostic codes or logged diagnostic codes, refer to the Troubleshooting Manual for your machine application. Battery Cables and/or Batteries
Inspect the main power switch, battery posts, and battery cables for loose connections and corrosion. If the battery cables are corroded, remove the battery cables and clean the battery cables. Clean the battery posts. Replace the cables. Tighten any loose connections.
Inspect the batteries.
Charge the batteries.
Load test the batteries. Refer to Systems Operation, Testing and Adjusting, "Battery - Test". Starting Motor Solenoid or Starting Circuit
Test the operation of the starting motor solenoid. Refer to Systems Operation, Testing and Adjusting, "Electric Starting System - Test".
Check the wiring to the starting motor solenoid. Starting Motor and/or Flywheel Ring Gear
Test the operation of the starting motor. Check the wiring for the starting motor. Refer to Systems Operation, Testing and Adjusting, "Electric Starting System - Test".
Inspect the pinion on the starting motor and the flywheel ring gear for damage. Electrical Power Supply
Check the electrical power supply. Refer to Troubleshooting, "Electrical Power Supply Circuit - Test".Internal Engine Fault
Remove the glow plugs (if equipped). Refer to Disassembly and Assembly, "Glow Plugs - Remove and Install".
If glow plugs are not installed, remove the fuel injection nozzles. Refer to Disassembly and Assembly, "Fuel Injection Nozzles - Remove".
Attempt to rotate the crankshaft through 360 degrees in both direction. If the crankshaft rotates correctly but fluid is expelled from the hole for the glow plug or the hole for the fuel injection nozzle, investigate the cause of the fluid in the cylinder.
If the crankshaft rotates correctly and no fluid is expelled, install the glow plugs (if equipped). Refer to Disassembly and Assembly, "Glow Plugs - Remove and Install".
If the crankshaft rotates correctly and no fluid is expelled, install the fuel injection nozzles. Refer to Disassembly and Assembly, "Fuel Injection Nozzles - Install".
If the engine does not rotate in Step 3, disassemble the engine. Refer to Disassembly and Assembly.
Inspect the internal components for the following conditions:
Seizure
Broken components
Bent components
Machine security system
Battery cables and/or batteries
Starting motor solenoid or starting circuit
Starting motor and/or flywheel ring gear
Electrical power supply
Internal engine faultRecommended Repairs
Machine Security System
Verify that the correct key is being used. Turn the key to the ON position.
Use the electronic service tool in order to check if diagnostic code 1639-09 is active. Verify that the lamp for the machine security system is on.
If the 1639-09 diagnostic code is active the machine security system is armed. Deactivate the machine security system and try to start the engine.
If the engine will not start use the electronic service tool to check for active diagnostic codes and logged diagnostic codes.
Investigate any active diagnostic codes and logged diagnostic codes and make all necessary repairs in order to eliminate the diagnostic codes.
If there are no active diagnostic codes or logged diagnostic codes, refer to the Troubleshooting Manual for your machine application. Battery Cables and/or Batteries
Inspect the main power switch, battery posts, and battery cables for loose connections and corrosion. If the battery cables are corroded, remove the battery cables and clean the battery cables. Clean the battery posts. Replace the cables. Tighten any loose connections.
Inspect the batteries.
Charge the batteries.
Load test the batteries. Refer to Systems Operation, Testing and Adjusting, "Battery - Test". Starting Motor Solenoid or Starting Circuit
Test the operation of the starting motor solenoid. Refer to Systems Operation, Testing and Adjusting, "Electric Starting System - Test".
Check the wiring to the starting motor solenoid. Starting Motor and/or Flywheel Ring Gear
Test the operation of the starting motor. Check the wiring for the starting motor. Refer to Systems Operation, Testing and Adjusting, "Electric Starting System - Test".
Inspect the pinion on the starting motor and the flywheel ring gear for damage. Electrical Power Supply
Check the electrical power supply. Refer to Troubleshooting, "Electrical Power Supply Circuit - Test".Internal Engine Fault
Remove the glow plugs (if equipped). Refer to Disassembly and Assembly, "Glow Plugs - Remove and Install".
If glow plugs are not installed, remove the fuel injection nozzles. Refer to Disassembly and Assembly, "Fuel Injection Nozzles - Remove".
Attempt to rotate the crankshaft through 360 degrees in both direction. If the crankshaft rotates correctly but fluid is expelled from the hole for the glow plug or the hole for the fuel injection nozzle, investigate the cause of the fluid in the cylinder.
If the crankshaft rotates correctly and no fluid is expelled, install the glow plugs (if equipped). Refer to Disassembly and Assembly, "Glow Plugs - Remove and Install".
If the crankshaft rotates correctly and no fluid is expelled, install the fuel injection nozzles. Refer to Disassembly and Assembly, "Fuel Injection Nozzles - Install".
If the engine does not rotate in Step 3, disassemble the engine. Refer to Disassembly and Assembly.
Inspect the internal components for the following conditions:
Seizure
Broken components
Bent components
Caterpillar parts catalog:
Parts spider Caterpillar catalog:
9P0356
SPIDER & BEARING AS
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 16G, 16H, 16H NA, 3...
120H, 120H ES, 120H NA, 120K, 120K 2, 12H, 12H ES, 12H NA, 12K, 135H, 135H NA, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 14H, 14H NA, 160H, 160H ES, 160H NA, 160K, 163H, 163H NA, 16G, 16H, 16H NA, 3...
8S8573
SPIDER
3406, D10
3406, D10
8P8132
SPIDER & BEARING GP
776C, 777B, 994, D10, D11N
776C, 777B, 994, D10, D11N
7V4077
SPIDER & BEARING GP
515, 525, 528, 528B, 530B, 950B, 950B/950E, 950F, 950F II, 960F
515, 525, 528, 528B, 530B, 950B, 950B/950E, 950F, 950F II, 960F
8V7177
SPIDER & BEARING AS
528, 528B, 530B
528, 528B, 530B
1V2970
SPIDER
528
528
3428662
SPIDER AS-FAN
320E L, 320E LRR
320E L, 320E LRR
3803884
SPIDER AS-FAN
2384C, 2484C, 559C, 579C
2384C, 2484C, 559C, 579C
3482422
SPIDER
584
584
3470166
SPIDER
584
584
1999721
SPIDER AS-FAN
550B, 560B, 570B, 580B
550B, 560B, 570B, 580B
1V6270
SPIDER
518
518
1V2970
SPIDER
528
528
9K1971
SPIDER AND BEARING ASSEM.
16, 518
16, 518