1156427 SPRING Caterpillar parts
318B, 320B, 320B L, OEMS
Rating:
Alternative (cross code) number:
CA1156427
115-6427
1156427
CA1156427
115-6427
1156427
Weight: 119 pounds 53 kg.
Information:
ACTUAL RATE
1438
N/MM
FREE LENGTH
501
mm
OD
218
mm
SOLID LENGTH
345
mm
WIRE DIAMETER
46
mm
EXCAVATOR, UNDERCARRIAGE,
Related part:
1156427
SPRING-YM
3014776
CL
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
1156427 Cuff Dual Port Reusable 30 Ea 60-7500-005-00 Sold Individually MADE BY Zimmer, Inc
ZIMMER
ZIMMER
1156427 Cuff Dual Port Reusable 30 Ea 60-7500-005-00 Sold Individually MADE BY Zimmer, Inc
ZIMMER
ZIMMER
Number on catalog scheme:
3
For full view, you need register
1156427
Images:
Information:
Note: The 163-0096 Diagnostic and Calibration Tool can be used in order to troubleshoot this component. Refer to the "Owner's Manual" for more information.The following procedure should be used in order to troubleshoot the thermocouple module.
Determine the number of thermocouples that have a problem.The results of the preceding procedure are in the following list:
The problem appears in the first four thermocouples in a module or the last four thermocouples in a module. Proceed to test step 4.
The problem is a single reading for the thermocouples or all of the thermocouples in a single module. Proceed to test step 5.
Bodily contact with electrical potential can cause bodily injury or death.To avoid the possibility of injury or death, ensure that the main power supply has been disconnected before performing any maintenance or removing any modules.
To avoid potential damage to the processor, handle all modules by the ends of the carrier or edges of the plastic housing. Skin oil or dirt can corrode metallic surfaces, inhibiting electrical contact.
Disconnect the power supply.
Check the electrical connectors and check the wiring for damage or bad connections.
Check the cold junction compensator.
Disconnect the power supply.
Exchange the cold junction compensator on the module.
Connect the power supply.The results of the preceding procedure are in the following list:
The problem follows the cold junction compensator. Test the cold junction compensator. Refer to test step 7.
The problem stays with the 4 thermocouples. Proceed to test step 5.
Test the thermocouples.
Disconnect the power supply.
Perform a test on the thermocouples. Refer to Troubleshooting, "Thermocouple Sensor".The results of the preceding procedure are in the following list:
The thermocouples are not functioning properly. Replace the thermocouples that are not functioning properly.
The thermocouples are functioning properly. Test the thermocouple module. Proceed to test step 6.
Check the module.
Disconnect the power supply.
Remove the module from the base.Reference: Testing and Adjusting, "Input Module and Output Module - Replace".
Disconnect the power supply from a known good base.
Install the module into the known good base.
Connect the power supply to the known good base.The results of the preceding procedure are in the following list:
The module is functioning normally. Check the pins in the terminal base. Repair any damaged pins.
The module is not functioning normally. Replace the module. Refer to Testing and Adjusting, "Input Module and Output Module - Replace".
Test the cold junction compensator.
Locate the three pins on the side of the cold junction compensator.
Measure the resistance between the two outside pins.The results of the preceding procedure are in the following list:
The resistance is greater than 10,000 ohms when the temperature is 21 °C (70 °F). The cold junction compensator is functioning properly. Proceed to test step 5.
The resistance is NOT greater than 10,000 ohms when the temperature is 21 °C (70 °F). The cold junction compensator is NOT functioning properly. Replace the cold junction compensator.Note: The resistance of the cold junction compensator changes with temperature.
Determine the number of thermocouples that have a problem.The results of the preceding procedure are in the following list:
The problem appears in the first four thermocouples in a module or the last four thermocouples in a module. Proceed to test step 4.
The problem is a single reading for the thermocouples or all of the thermocouples in a single module. Proceed to test step 5.
Bodily contact with electrical potential can cause bodily injury or death.To avoid the possibility of injury or death, ensure that the main power supply has been disconnected before performing any maintenance or removing any modules.
To avoid potential damage to the processor, handle all modules by the ends of the carrier or edges of the plastic housing. Skin oil or dirt can corrode metallic surfaces, inhibiting electrical contact.
Disconnect the power supply.
Check the electrical connectors and check the wiring for damage or bad connections.
Check the cold junction compensator.
Disconnect the power supply.
Exchange the cold junction compensator on the module.
Connect the power supply.The results of the preceding procedure are in the following list:
The problem follows the cold junction compensator. Test the cold junction compensator. Refer to test step 7.
The problem stays with the 4 thermocouples. Proceed to test step 5.
Test the thermocouples.
Disconnect the power supply.
Perform a test on the thermocouples. Refer to Troubleshooting, "Thermocouple Sensor".The results of the preceding procedure are in the following list:
The thermocouples are not functioning properly. Replace the thermocouples that are not functioning properly.
The thermocouples are functioning properly. Test the thermocouple module. Proceed to test step 6.
Check the module.
Disconnect the power supply.
Remove the module from the base.Reference: Testing and Adjusting, "Input Module and Output Module - Replace".
Disconnect the power supply from a known good base.
Install the module into the known good base.
Connect the power supply to the known good base.The results of the preceding procedure are in the following list:
The module is functioning normally. Check the pins in the terminal base. Repair any damaged pins.
The module is not functioning normally. Replace the module. Refer to Testing and Adjusting, "Input Module and Output Module - Replace".
Test the cold junction compensator.
Locate the three pins on the side of the cold junction compensator.
Measure the resistance between the two outside pins.The results of the preceding procedure are in the following list:
The resistance is greater than 10,000 ohms when the temperature is 21 °C (70 °F). The cold junction compensator is functioning properly. Proceed to test step 5.
The resistance is NOT greater than 10,000 ohms when the temperature is 21 °C (70 °F). The cold junction compensator is NOT functioning properly. Replace the cold junction compensator.Note: The resistance of the cold junction compensator changes with temperature.
Caterpillar parts catalog:
Parts spring Caterpillar catalog:
311C, 313D2 LGP, 315C, 315D L, 316E L, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320B, 320B FM LL, 320B L, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 32...
307C, 308C, 311B, 311C, 311D LRR, 311F LRR, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315C, 315D L, 316E L...
311, 311B, 311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 320N, 321C, 323D L, 323D LN
311, 311B, 311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 320N, 321C, 323D L, 323D LN
311, 311B, 311C, 312, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320B U, 320C, 320C FM, 320C L, 320D, 320D LRR, 320N, 321C, 323D L, 323D LN
315D L, 316E L, 318C, 318D L, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320B L, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, ...
215B, 225, 229D, 231D, 320 L, 320B, 321B, 322B L, 322B LN, 325, 325 L, 325 LN, 325B, 325B L, 5130, 5130B, 5230, 539, 844, 854G, 990, 990 II, 992G, E300B, M325B
320 L, 320B, 320B FM LL, 322B L, 325, 325 L, 325 LN, 325B, 325B L, OEMS
1090, 1190, 1190T, 1390, 2290, 2390, 322B L, 322C, 322C FM, 324D FM, 325 L, 325B L, 325C, 325C FM, 325C L, 511, 521, OEMS, TK711, TK721, TK741
322, 322 FM L, 322B, 322B L, 322B LN, OEMS
330, 330 FM L, 330B L, 330C FM, 330C L, 330C MH, 350, OEMS, TK1051
330, 330 FM L, 330 L, 330B, 330B L, OEMS
1275956
SPRING
307, 311C, 311D LRR, 312C, 312C L, 312D L, 313D, 314C, 314D LCR, 315, 315B, 315C, 315D L, 317B LN, 318B, 318C, 319C, 319D L, 319D LN, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D L, 32...
307, 311C, 311D LRR, 312C, 312C L, 312D L, 313D, 314C, 314D LCR, 315, 315B, 315C, 315D L, 317B LN, 318B, 318C, 319C, 319D L, 319D LN, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D L, 32...
0952130
SPRING
307, 315, 315B, 315B FM L, 315C, 317B LN, 318B, 933, 933C, 939C, D3C III, D3G, D4C III, D4G, D5C III, D5G, E70, E70B
307, 315, 315B, 315B FM L, 315C, 317B LN, 318B, 933, 933C, 939C, D3C III, D3G, D4C III, D4G, D5C III, D5G, E70, E70B
1185766
SPRING
315, 315B, 315B FM L, 315C, 317B LN, 318B, 933, 933C, 939C, D3C III, D3G, D4C III, D4G, D5C III, D5G
315, 315B, 315B FM L, 315C, 317B LN, 318B, 933, 933C, 939C, D3C III, D3G, D4C III, D4G, D5C III, D5G
1185765
SPRING
315, 315B, 315C, 317B LN, 318B, 933, 933C, 939C, D3C III, D3G, D4C III, D4G, D5C III, D5G
315, 315B, 315C, 317B LN, 318B, 933, 933C, 939C, D3C III, D3G, D4C III, D4G, D5C III, D5G
0952280
SPRING-PUMP
307, 307B, 308C, 315, 315B, 315C, 317B LN, 318B, 933, 933C, 939C, D3C III, D3G, D4C III, D4G, D5C III, D5G, E120, E140, E70, E70B
307, 307B, 308C, 315, 315B, 315C, 317B LN, 318B, 933, 933C, 939C, D3C III, D3G, D4C III, D4G, D5C III, D5G, E120, E140, E70, E70B
1184820
SPRING
315, 315B, 315C, 317B LN, 318B, 933, 933C, 939C, D3C III, D4C III, D5C III, D5G
315, 315B, 315C, 317B LN, 318B, 933, 933C, 939C, D3C III, D4C III, D5C III, D5G
311C, 311D LRR, 311F LRR, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315C, 315D L, 316E L, 318B, 318C, 318D...
315C, 318B, 318C, 319D L, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 322B L, 322B LN, 322C, 322C FM, 325 L, 325B, 325B L, 330 L, 330B L, OEMS
311C, 313D2 LGP, 315C, 315D L, 316E L, 318B, 318C, 318D L, 318D2 L, 319D L, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 322, 322B L, 322B LN, 322C, 322C FM, 325B, 325B L, 330B, 330B L, OEMS
311C, 313D2 LGP, 315C, 315D L, 316E L, 318B, 318C, 318D L, 318D2 L, 319D L, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 321C, 322, 322B L, 322B LN, 322C, 322C FM, 325B, 325B L, 330B, 330B L, OEMS
318B, 318C, 318E L, 319D, 319D L, 319D LN, 320 L, 320C, 320C FM, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 320N, 321C, 321D LCR, 32...
315B FM L, 317B LN, 318B, 320 L, 320N, OEMS