1232489 SPRING Caterpillar parts
320B, 322B, 325B, 330B, 330B L
Rating:
Alternative (cross code) number:
CA1232489
123-2489
1232489
CA1232489
123-2489
1232489
Weight: 0.01 pounds 0 kg.
Information:
ACTUAL RATE
1.5873
N/MM
FREE LENGTH
40
mm
OD
8
mm
SOLID LENGTH
20.3
mm
WIRE DIAMETER
1
mm
EXCAVATOR,
Number on catalog scheme:
24
For full view, you need register
Information:
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 2P-8260 Cylinder Liner Installer 1
C - Loctite Silicone Lubricant / Dielectric Grease
LB 8801/LB 8423(1) —
- LB-8104 1652339(2) —
D - Emery Cloth (Fine) 1
(1) Preferred lubricant
(2) For EAME use only
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Check the cylinder liner projection. Refer to Testing and Adjusting, "Cylinder Liner Projection".
Illustration 1 g03326886
After the cylinder liner is prepared, use Tooling (B) to press the cylinder liner into the cylinder block.
Use a 0.02 mm (0.001 inch) feeler gauge to verify that the cylinder liner is against the cylinder block. Check for gaps in multiple places. A gap between the cylinder liner and the cylinder block can indicate a liner seal that is pinched. A liner seal that is pinched will compromise the life of the liner seal and the cylinder head gasket.Types of Cylinder Liner Seals
There are two types of seals that can be used on the cylinder liners.Type 1
Illustration 2 g02130336
Illustration 3 g02248239
Apply liquid soap on the grooves for O-ring seals (1) and on O-ring seals (1). Install O-ring seals (1) on cylinder liner (2). Also, coat the bottom cylinder block bore, Location (N), with liquid soap.
Dip filler band (3) in clean engine oil. Immediately install filler band (3) onto cylinder liner (2).
Immediately install cylinder liner (2) before filler band (3) can expand.Type 2
Illustration 4 g02175641
Liner seal (4) requires a machined chamfer at the top edge of the liner bore to install the liner seal.
A chamfer can be machined into the top edge of the bore in the block for the cylinder liner. Refer to Special Instruction, SEBF9203 for the correct procedure for machining the chamfer.Note: Liner seat inserts that include the chamfer are also available. Refer to Reuse and Salvage Guidelines, SEBF8255.
Use Tooling (D) on the inside surface of the top bore, Location (M).
Ensure that the liner groove for liner seal (4) is clean and dry. Install liner seal (4) on cylinder liner (2). Apply a thin coat of Tooling (C) to the cylinder block on the machined chamfer to a distance of 5 mm (0.2 inch) below the machined chamfer. Apply Tooling (C) to liner seal (4).Note: Do not apply Tooling (C) to the liner flange or the top of the cylinder block.
Apply liquid soap on the grooves for O-ring seals (1) and on O-ring seals (1). Install O-ring seals (1) on cylinder liner (2). Also, coat the bottom cylinder block bore, Location (N), with liquid soap.End By:
Install the pistons and the connecting rod assemblies.
Table 1
Required Tools
Tool Part Number Part Description Qty
B 2P-8260 Cylinder Liner Installer 1
C - Loctite Silicone Lubricant / Dielectric Grease
LB 8801/LB 8423(1) —
- LB-8104 1652339(2) —
D - Emery Cloth (Fine) 1
(1) Preferred lubricant
(2) For EAME use only
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Check the cylinder liner projection. Refer to Testing and Adjusting, "Cylinder Liner Projection".
Illustration 1 g03326886
After the cylinder liner is prepared, use Tooling (B) to press the cylinder liner into the cylinder block.
Use a 0.02 mm (0.001 inch) feeler gauge to verify that the cylinder liner is against the cylinder block. Check for gaps in multiple places. A gap between the cylinder liner and the cylinder block can indicate a liner seal that is pinched. A liner seal that is pinched will compromise the life of the liner seal and the cylinder head gasket.Types of Cylinder Liner Seals
There are two types of seals that can be used on the cylinder liners.Type 1
Illustration 2 g02130336
Illustration 3 g02248239
Apply liquid soap on the grooves for O-ring seals (1) and on O-ring seals (1). Install O-ring seals (1) on cylinder liner (2). Also, coat the bottom cylinder block bore, Location (N), with liquid soap.
Dip filler band (3) in clean engine oil. Immediately install filler band (3) onto cylinder liner (2).
Immediately install cylinder liner (2) before filler band (3) can expand.Type 2
Illustration 4 g02175641
Liner seal (4) requires a machined chamfer at the top edge of the liner bore to install the liner seal.
A chamfer can be machined into the top edge of the bore in the block for the cylinder liner. Refer to Special Instruction, SEBF9203 for the correct procedure for machining the chamfer.Note: Liner seat inserts that include the chamfer are also available. Refer to Reuse and Salvage Guidelines, SEBF8255.
Use Tooling (D) on the inside surface of the top bore, Location (M).
Ensure that the liner groove for liner seal (4) is clean and dry. Install liner seal (4) on cylinder liner (2). Apply a thin coat of Tooling (C) to the cylinder block on the machined chamfer to a distance of 5 mm (0.2 inch) below the machined chamfer. Apply Tooling (C) to liner seal (4).Note: Do not apply Tooling (C) to the liner flange or the top of the cylinder block.
Apply liquid soap on the grooves for O-ring seals (1) and on O-ring seals (1). Install O-ring seals (1) on cylinder liner (2). Also, coat the bottom cylinder block bore, Location (N), with liquid soap.End By:
Install the pistons and the connecting rod assemblies.
Caterpillar parts catalog:
Parts spring Caterpillar catalog:
311C, 313D2 LGP, 315C, 315D L, 316E L, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320B, 320B FM LL, 320B L, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 32...
307C, 308C, 311B, 311C, 311D LRR, 311F LRR, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315C, 315D L, 316E L...
311, 311B, 311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 320N, 321C, 323D L, 323D LN
311, 311B, 311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 320N, 321C, 323D L, 323D LN
311, 311B, 311C, 312, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320B U, 320C, 320C FM, 320C L, 320D, 320D LRR, 320N, 321C, 323D L, 323D LN
315D L, 316E L, 318C, 318D L, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320B L, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, ...
215B, 225, 229D, 231D, 320 L, 320B, 321B, 322B L, 322B LN, 325, 325 L, 325 LN, 325B, 325B L, 5130, 5130B, 5230, 539, 844, 854G, 990, 990 II, 992G, E300B, M325B
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 324E, 324E L, 324E LN, 325B, 325B L, 325C, 325C FM, 325D, 325D...
320 L, 320B, 320B FM LL, 322B L, 325, 325 L, 325 LN, 325B, 325B L, OEMS
322, 322 FM L, 322B, 322B L, 322B LN, OEMS
330, 330 FM L, 330B L, 330C FM, 330C L, 330C MH, 350, OEMS, TK1051
330, 330 FM L, 330 L, 330B, 330B L, OEMS
320B, 322B, 325B, 330B, 330B L
320B, 322B, 325B, 330B, 330B L
320 L, 320B, 320B L, 320N, 345B, 345B L, OEMS
M320, M322C, M322D, M322D MH
1290764
SPRING-GAS
M320
M320
1992392
SPRING
320B, 322B LN, 325B L, 330B L, 345B II, 345B L
320B, 322B LN, 325B L, 330B L, 345B II, 345B L
1625873
SPRING
550, 550B, 560B, 570, 570B, 580, 580B
550, 550B, 560B, 570, 570B, 580, 580B
2252416
SPRING
525B, 525C, 535B, 545
525B, 525C, 535B, 545
1687795
SPRING AS
535B, 545
535B, 545
2470C, 2570C, 2670C, 2864C, 525B, 525C, 525D, 533, 535B, 535C, 535D, 543, 545, 545C, 545D, 553C, 555D, 563C, 573C, 586C, HA770, HA771, HA870, HA871, TK370, TK371, TK380, TK381
1437355
SPRING
545, 545C, 545D, 555D
545, 545C, 545D, 555D
320B