1315864 SPRING Caterpillar parts
311, 311B, 312B, 312B L, 313B, 315B L, 318B, 320B, 322B, 322B L, 322B LN, 325B, 325B L, 330B L, 345B L, 350, 375, 375 L, 5080, R1300, R1300G, R1600, R1600G, R1600H, R1700G, R2900, R2900G, R3000H
Rating:
Alternative (cross code) number:
CA1315864
131-5864
1315864
CA1315864
131-5864
1315864
Weight: 0.01 pounds 0 kg.
Information:
ACTUAL RATE
0
N/MM
FREE LENGTH
34.1
mm
OD
8.6
mm
SOLID LENGTH
0
mm
WIRE DIAMETER
1
mm
EXCAVATOR, LOAD HAUL DUMP,
Compatible equipment models: 1315864:
Number on catalog scheme:
13
For full view, you need register
Information:
Test Procedure
System Operation
The SLC 5/04 - 5/05 diagnostic indicators are located on the front of the following components: Power Supply, CPU and I/O Modules.The diagnostic indicators help trace the source of the fault. Faults can be found in the following components: input devices, output devices, wiring and the controller.
Illustration 1 g00766224
Diagram of the LED indicators
Illustration 2 g00562937
Central Processing Unit for typical systemFunctional Test
Check the electrical connectors and check the wiring.
Bodily contact with electrical potential can cause bodily injury or death.To avoid the possibility of injury or death, ensure that the main power supply has been disconnected before performing any maintenance or removing any modules.
Disconnect the power supply.
Check the electrical connectors and check the wiring for damage or bad connections.
Verify that all modules are properly seated.
Connect the power supply.
Verify the status of the LED on the SLC 5/04 - 5/05.The results of the preceding procedure are in the following list:
All of the components are fully installed. All of the components are free of corrosion. All of the components are free of damage. All of the modules are properly seated. Proceed to 2.
The components are not fully installed. The components are not free of corrosion. The components are damaged. All of the modules are not properly seated. Repair the component. Verify that the repair resolves the problem. STOP.
Check the line voltage.
Reconnect the power supply.
Measure the line voltage at the terminals.
Verify the voltage of the power supply. The power supply voltage should be measured between 21.0 VDC and 28.0 VDC.The results of the preceding procedure are in the following list:
The line voltage is in the range. Proceed to 3.
The line voltage is out of the range. Refer to Troubleshooting, "System Power". Stop.
Attempt to operate the processor in the "RUN" mode.
Place the switch in the RUN position.The results of the preceding procedure are in the following list:
The processor enters the "RUN" mode. The processor resumes normal operation. Stop.
The processor will not enter the "RUN" mode. Proceed to 4.
Check the processor.
To avoid damage to electronic components, do not remove the processor from the SLC 5/04 Chassis until all power is removed from the power supply.Do not expose memory modules to surfaces or areas that may typically hold an electrostatic charge.
Bodily contact with electrical potential can cause bodily injury or death.To avoid the possibility of injury or death, ensure that the main power supply has been disconnected before performing any maintenance or removing any modules.
Disconnect the power supply.
Remove the processor from the chassis.
Install the processor in another chassis.
Connect the power supply.
Configure the power supply.
Attempt to operate the processor in the "RUN" mode.The results of the preceding procedure are in the following list:
The processor enters the "RUN" mode. The processor will not perform functions in the run mode. Replace the chassis. Verify that the repair solves the problem. Stop.
The processor will not enter the "RUN" mode. Replace the processor. Refer to Maintenance Procedure, "Processor - Replace".
System Operation
The SLC 5/04 - 5/05 diagnostic indicators are located on the front of the following components: Power Supply, CPU and I/O Modules.The diagnostic indicators help trace the source of the fault. Faults can be found in the following components: input devices, output devices, wiring and the controller.
Illustration 1 g00766224
Diagram of the LED indicators
Illustration 2 g00562937
Central Processing Unit for typical systemFunctional Test
Check the electrical connectors and check the wiring.
Bodily contact with electrical potential can cause bodily injury or death.To avoid the possibility of injury or death, ensure that the main power supply has been disconnected before performing any maintenance or removing any modules.
Disconnect the power supply.
Check the electrical connectors and check the wiring for damage or bad connections.
Verify that all modules are properly seated.
Connect the power supply.
Verify the status of the LED on the SLC 5/04 - 5/05.The results of the preceding procedure are in the following list:
All of the components are fully installed. All of the components are free of corrosion. All of the components are free of damage. All of the modules are properly seated. Proceed to 2.
The components are not fully installed. The components are not free of corrosion. The components are damaged. All of the modules are not properly seated. Repair the component. Verify that the repair resolves the problem. STOP.
Check the line voltage.
Reconnect the power supply.
Measure the line voltage at the terminals.
Verify the voltage of the power supply. The power supply voltage should be measured between 21.0 VDC and 28.0 VDC.The results of the preceding procedure are in the following list:
The line voltage is in the range. Proceed to 3.
The line voltage is out of the range. Refer to Troubleshooting, "System Power". Stop.
Attempt to operate the processor in the "RUN" mode.
Place the switch in the RUN position.The results of the preceding procedure are in the following list:
The processor enters the "RUN" mode. The processor resumes normal operation. Stop.
The processor will not enter the "RUN" mode. Proceed to 4.
Check the processor.
To avoid damage to electronic components, do not remove the processor from the SLC 5/04 Chassis until all power is removed from the power supply.Do not expose memory modules to surfaces or areas that may typically hold an electrostatic charge.
Bodily contact with electrical potential can cause bodily injury or death.To avoid the possibility of injury or death, ensure that the main power supply has been disconnected before performing any maintenance or removing any modules.
Disconnect the power supply.
Remove the processor from the chassis.
Install the processor in another chassis.
Connect the power supply.
Configure the power supply.
Attempt to operate the processor in the "RUN" mode.The results of the preceding procedure are in the following list:
The processor enters the "RUN" mode. The processor will not perform functions in the run mode. Replace the chassis. Verify that the repair solves the problem. Stop.
The processor will not enter the "RUN" mode. Replace the processor. Refer to Maintenance Procedure, "Processor - Replace".
Caterpillar parts catalog:
Parts spring Caterpillar catalog:
772, 773, 825C, 826C, 834B, 980C, 988B, 988F, 992, 992C, 992D, R2900, R2900G, R3000H
2470C, 2570C, 2670C, 2864C, 525B, 525C, 525D, 533, 535B, 535C, 535D, 543, 545, 545C, 545D, 553C, 555D, 563C, 573C, 586C, 950F, 950F II, 960F, HA770, HA771, HA870, HA871, R1300, R1300G, R1300G II, TK37...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 324E, 324E L, 324E LN, 325C, 325C FM, 325D, 325D FM, 325D FM LL, 325D L, 325D M...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 322B L, 322B LN, 322C, 322C FM, 324D, 324D FM, 324D FM LL, 324D L, 324D LN, 324E, 324E L, 324E LN, 325B, 325B L, 325C, 325C FM, 325D, 325D...
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E HVG, 336E L, 336E LN, 340D L, 340D2 L, 345C, 345C L, 345C MH, 350, 568 FM LL, M330D, W345C MH
320 L, 320B, 320B FM LL, 322B L, 325, 325 L, 325 LN, 325B, 325B L, OEMS
1090, 1190, 1190T, 1390, 2290, 2390, 322B L, 322C, 322C FM, 324D FM, 325 L, 325B L, 325C, 325C FM, 325C L, 511, 521, OEMS, TK711, TK721, TK741
322, 322 FM L, 322B, 322B L, 322B LN, OEMS
330, 330 FM L, 330B L, 330C FM, 330C L, 330C MH, 350, OEMS, TK1051
330, 330 FM L, 330 L, 330B, 330B L, OEMS
330, 330 FM L, 330 L, 345B, 345B II, 345B L, 345C, 345C L, 350, 365B, 365B II, 365B L, 365C, 365C L, 365C L MH, OEMS
330, 330 FM L, 330 L, 330B, 330B L, 345B, 345B L, W330B
307C, 308C, 311, 311B, 311C, 311D LRR, 311F LRR, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313B, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E ...
311, 311B, 312B, 312B L, 313B, 315B L, 318B, 320B, 322B, 322B L, 322B LN, 325B, 325B L, 330B L, 345B L, 350, 375, 375 L, 5080, R1300, R1300G, R1600, R1600G, R1600H, R1700G, R2900, R2900G, R3000H
311B, 312B, 312B L, 313B, 315B, 315B L, 317B LN, 318B
311B, 312B, 312B L, 313B, 315B, 315B L, 317B LN, 318B
1360127
SPRING
311B, 312B, 312B L, 313B, 315B L, 317B LN, 318B
311B, 312B, 312B L, 313B, 315B L, 317B LN, 318B
1425274
SPRING
311B, 312B, 312B L, 313B, 315B, 315B L, 317B LN, 318B
311B, 312B, 312B L, 313B, 315B, 315B L, 317B LN, 318B
307B, 311B, 312B L, 313B, 315B L, 317B LN, 318B, 320B, 322B L, 322B LN, 325B, 325B L, 330B L, 345B, 345B II, 345B II MH, 345B L, 5110B, 539, M325B, TK1051, W330B, W345B II
311B, 312B, 312B L, 315B, 315B FM L, 315B L, 317B LN, 318B, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, 345C, 345C L, 345C MH, M330D, W345C MH
311B, 312B, 312B L, 315B, 315B FM L, 315B L, 317B LN
1857911
SPRING
312B L, 315B L, 317B LN, 318B
312B L, 315B L, 317B LN, 318B
312B L, 315B L, 318B, 320B, 322B L, 322B LN, 325B L, 330B L, 345B L, 350, 375, 375 L, 5080, 5130, 5230, R1300, R1300G, R1600, R1600G, R1600H, R1700G, R2900, R2900G, R3000H
311, 311B, 312B, 312B L, 315B L, 318B, 320B, 322B, 322B L, 322B LN, 325B, 325B L, 330B L, 345B L