2348983 SPRING Caterpillar parts
302.5C, 303E CR
Rating:
Alternative (cross code) number:
CA2348983
234-8983
2348983
CA2348983
234-8983
2348983
Weight: 10 pounds 4 kg.
MINI HYD EXCAVATOR,
Information:
Illustration 1 g02789965
Schematic for the Boom Angle sensor
This diagnostic code is associated with the Boom Angle sensor. An FMI 04 diagnostic code indicates the Machine ECM has determined the sensor circuit voltage is below normal.For machines equipped with the E-Fence feature, reference Troubleshooting, "E-Ceiling and Cab Avoidance - Troubleshoot"Possible causes for this diagnostic code are listed below:
Sensor power supply failure.
The sensor has failed.
Sensor output shorted to ground.
The Machine ECM has failed. This situation is unlikely. Note: Poor connections are often the cause of a problem in electrical circuits. Before performing this procedure, inspect all the machine harnesses and connectors involved in the circuit. Make sure to verify that all of the connections in the circuit are clean, secure, and in good condition. Correct any problems found with any of the connections. Verify the diagnostic code CID 2425 FMI 04 is still active, before continuing with this procedure.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes now, but clear those diagnostic codes when the original diagnostic code has been corrected. Test Step 1. CHECK THE SENSOR POWER SUPPLY
Turn the key start switch and the disconnect switch to the ON position.
At the machine harness connector for the Boom Angle sensor, measure the voltage between contact A (wire A760-GY(Grey)) and contact B (wire A209-BK(Black)). Expected Result:The voltage is 5 VDC.Results:
YES - The voltage is 5 VDC. Go to Test Step 2.
NO - The voltage is not 5 VDC. Repair: There is a problem with the 5 VDC power supply from the Machine ECM. Use MID 039 CID 0262 FMI 06 diagnostic code to troubleshoot the power supply. After the supply is corrected, check if the CID 2425 FMI 04 diagnostic code is active.If the diagnostic code is active, go to Test Step 2.Test Step 2. CHECK THE SENSOR.
Turn the disconnect switch and the key start switch to the OFF position.
Disconnect the machine harness connector from the Boom Angle sensor.
Turn the disconnect switch and the key start switch to the ON position.
Observe the status of the CID 2425 FMI 04 diagnostic code. Expected Result:The CID 2425 FMI 04 diagnostic code remains active. Results:
YES - The CID 2425 FMI 04 diagnostic code remains active. The sensor is not the cause of the problem. Go to Test Step 3.
NO - The CID 2425 FMI 04 diagnostic code has been replaced by the CID 2425 FMI 03 diagnostic code. The sensor has failed. Repair: Replace the sensor. The new sensor may require calibration. Go to Test Step 4.Test Step 3. CHECK THE SENSOR CIRCUIT FOR A SHORT.
The sensor remains disconnected from the machine harness.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect both the J1 and J2 harness connector from the Machine ECM.
At the J1 machine harness connector, measure the resistance from contact J1-5 (wire E441-GN(Green)) to all contacts used in the J1 and J2 ECM harness connectors. Expected Result:The all measurements are more than 5000 ohms.Results:
YES - The measurements are all more than 5000
Caterpillar parts catalog:
Parts spring Caterpillar catalog:
1935195
SPRING
302.5C, 3056
302.5C, 3056
7I7403
SPRING
303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304, 304C CR, 304D CR, 304E, 305, 305.5, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 306, 307, 307B, 307C, 308E, 308E CR, 308E SR, 311D LRR, 312, 312B L, 312C, 31...
303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304, 304C CR, 304D CR, 304E, 305, 305.5, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 306, 307, 307B, 307C, 308E, 308E CR, 308E SR, 311D LRR, 312, 312B L, 312C, 31...
1360148
SPRING
303, 303.5E, 303E CR, 304, 304E, 305, 305.5, 305.5E, 305E, 306, 306E, 307B, 307C, 308E SR, 313B, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR
303, 303.5E, 303E CR, 304, 304E, 305, 305.5, 305.5E, 305E, 306, 306E, 307B, 307C, 308E SR, 313B, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR
1500874
SPRING
303.5, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304D CR, 304E
303.5, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304D CR, 304E
2448495
SPRING
303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304C CR, 304D CR, 304E, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 307C, 308C, 311C, 311D LRR, 312C L, 312D, 312D L, 312D2, 314C, 314D LCR, 315C, 315D L, 318C, 3...
303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304C CR, 304D CR, 304E, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 307C, 308C, 311C, 311D LRR, 312C L, 312D, 312D L, 312D2, 314C, 314D LCR, 315C, 315D L, 318C, 3...
1968336
SPRING
302.5C, 303, 304, 305
302.5C, 303, 304, 305
1940784
SPRING
303, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304, 304C CR, 304D CR, 304E, 305, 305.5, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 306
303, 303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304, 304C CR, 304D CR, 304E, 305, 305.5, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 306
2658587
SPRING AS-GAS
303.5C, 303.5D, 303C CR, 303E CR, 304D CR
303.5C, 303.5D, 303C CR, 303E CR, 304D CR
2818631
SPRING
303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304C CR, 304D CR, 304E, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 307E, 308E, 308E CR, 308E SR, 308E2 CR
303.5C, 303.5D, 303.5E, 303C CR, 303E CR, 304C CR, 304D CR, 304E, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 307E, 308E, 308E CR, 308E SR, 308E2 CR
2674388
SPRING
302.5C
302.5C
2498078
SPRING AS-GAS
301.6C, 302.5C
301.6C, 302.5C
2327688
SPRING
301.6C
301.6C
2230353
SPRING
301.6C
301.6C
2674411
SPRING
301.6C
301.6C
3012373
SPRING-GOVERNOR
301.6C
301.6C
2725711
SPRING
303.5C, 303C CR, 304C CR, 305C CR
303.5C, 303C CR, 304C CR, 305C CR
2743550
SPRING AS
305.5, 305.5E, 306, 306E
305.5, 305.5E, 306, 306E
2743563
SPRING
305.5, 305.5E, 306, 306E, 308E2 CR
305.5, 305.5E, 306, 306E, 308E2 CR
3096627
SPRING
305.5, 306
305.5, 306
3096626
SPRING
305.5, 306
305.5, 306
2101793
SPRING-GAS
305.5
305.5