2487247 SPRING GP-RECOIL Caterpillar parts
320C, 320C FM
Rating:
Alternative (cross code) number:
CA2487247
248-7247
2487247
CA2487247
248-7247
2487247
EXCAVATOR,
Number on catalog scheme:
For full view, you need register
Information:
(20) Clutch body. A. Diameter (maximum) ... 175.79 mm (6.921 in)B. Diameter (minimum) ... 82.47 mm (3.247 in)C. Dowel pin hole. Diameter (maximum) ... 8.26 mm (.324 in)D. Diameter (maximum) with no nicks in the surface ... 58.78 mm (2.314 in)E. Threads. Make sure the threads are not damaged.(22) Piston housing. F. Width (maximum) ... 2.79 mm (.110 in)G. Diameter (maximum) with out any wear marks in the surface ... 82.60 mm (3.252 in)H. Dowel pin hole. Diameter (maximum) when new ... 8.92 mm (.351 in)I. Width (maximum) ... 3.12 mm (.123 in)J. Diameter (maximum) ... 176.28 mm (6.940 in) Snap rings must fit free in the grooves. The sides must be straight. The dowel pin hole (H) may become elongated do to wear. The maximum diameter across the elongation area must not exceed 10.16 mm (.400 in). Make sure all the adhesive has been removed. 6. Using FT2464 Plate (25), press the fan mounting hub from the front bearing retainer. Remove key (24) retaining these two items. 7. Remove snap ring (26). Drive the seal (27) out with a punch. Internal snap rings must not be damaged or worn on the sides. they must be flat and have square edges at the OD. 8. Use FT2462 Pressing Tube (29) and FT2465 Plate (28) to press bearing (30) from bearing retainer (7). Inspect: (7) Bearing retainer. A. The area must not have any nicks. The surface must seal against the OD of the oil seal. Diameter (maximum) ... 88.938 mm (3.5015 in)B. The area should not have any nick that rises above the surface.C. Snap ring. The sides must be straight. The snap ring must fit freely in the groove. Width (maximum) ... 1.19 mm (.047 in)D. The area must have straight sides and no nicks that rise above the surface. Diameter (maximum) ... 94.988 mm (3.7397 in) E. Any wear marks present in the slots must not have straight sides that would restrict the plate movement. If wear marks have smooth entry and exit marks, the notches will not restrict the plate movement and the retainer may be used again. 9. Remove the end cap (34) with FT2461 Pressing Tube (31). Inspect:(32) And (33) Sleeve bearings. If the bearings appear to be satisfactory then do not remove them, refer to the following illustration. Teflon/Bronze ID surface will appear dark bronze in color when new, and will progress to a light bronze color near the end of its useful life. The illustration visually indicates presence of dark teflon on the light bronze surface. (34) End cap. The area should not have any nicks that rise above the surface. A. Diameter (maximum) ... 60.48 mm (2.381 in) 10. If the sleeve bearings need replacement use FT2461 Pressing Bar (31) to remove both bearings (32) and (33) at the same time. 11. Inspect the seal retainer assembly (35). If the seal requires replacement, remove the seal retainer
Caterpillar SIS machinery equipment:
Parts spring Caterpillar catalog:
307B, 312B L, 312C, 315B L, 315C, 317B LN, 318B, 318C, 319C, 320 L, 320B, 320B FM LL, 320B U, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D...
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 303, 304, 305, 311C, 311D LRR, 312C L, 312D, 312D L, 312D2, 313D, 314C, 314D CR, 314D LCR, 315B FM L, 315C, 320B FM LL, 320C, 320C FM, 320...
303, 303.5C, 303.5D, 303.5E, 303C CR, 304, 304C CR, 304D CR, 304E, 305, 305.5, 305.5D, 305.5E, 305C CR, 305D CR, 305E, 306, 306E, 307, 307B, 307C, 307D, 307E, 308C, 308D, 308E, 308E CR, 308E SR, 308E2...
318B, 318C, 318E L, 319D, 319D L, 319D LN, 320 L, 320C, 320C FM, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2 L, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 320N, 321C, 321D LCR, 32...
311C, 313D2 LGP, 315C, 315D L, 316E L, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320B, 320B FM LL, 320B L, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 32...
307C, 308C, 311B, 311C, 311D LRR, 311F LRR, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 312E, 312E L, 313D, 313D2, 313D2 LGP, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 315C, 315D L, 316E L...
311, 311B, 311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 320N, 321C, 323D L, 323D LN
311, 311B, 311C, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D LRR, 320N, 321C, 323D L, 323D LN
311, 311B, 311C, 312, 312B, 312C, 312C L, 314C, 318C, 319C, 320 L, 320B, 320B U, 320C, 320C FM, 320C L, 320D, 320D LRR, 320N, 321C, 323D L, 323D LN
318C, 320C, 320C L, 321C
315D L, 316E L, 318C, 318D L, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320B L, 320C, 320C FM, 320C L, 320D, 320D FM, 320D FM RR, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR, 320D2, 320D2 GC, ...
315C, 318C, 319C, 320C
1501081
SPRING GP-RECOIL
304.5
304.5
1722106
SPRING GP-RECOIL
303.5
303.5
416, 416B, 426, 426B, 428, 428B, 436, 436B, 446, 446B, 924F, CB-434, CP-563, CS-583, IT18F, IT24F, R1300, R1300G, R1300G II, R1600, R1600G, R1600H, R1700 II, R1700G, R2900, R2900G, R3000H
1880358
SPRING GP-CAB DOOR
R1600, R1600G, R1700G
R1600, R1600G, R1700G
302.5
2322327
SPRING & MTG GP-LEVELER
PC206, PC310B
PC206, PC310B
2500691
SPRING GP-CAB DOOR
R2900G, R3000H
R2900G, R3000H
2394333
SPRING GP-RECOIL
330C L
330C L
2256870
SPRING AS-GAS
PM3516
PM3516