parts catalog

SPRING 2H9104 - Caterpillar

2H9104 SPRING Caterpillar parts D337 SPRING
Alternative (cross code) number:
Caterpillar 2H9104 SPRING

Buy SPRING 2H9104 Caterpillar genuine, new aftermarket tractor parts with delivery

Compatible equipment models: 2H9104:

MARINE ENGINE  D337   Caterpillar
Number on catalog scheme: None
  For full view, you need register


1. Drain the transmission oil.2. Disconnect the four oil lines from transmission oil pump (1), (two were removed during transmission removal).3. Remove two bolts (2), and remove transmission oil pump (1). The following steps are for installation of the transmission oil pump.4. Check the condition of all O-ring seals, and replace them if necessary.5. Put transmission oil pump (1) in position on the transmission case, and install two bolts (2).6. Connect the four oil lines to the transmission oil pump.7. Fill the transmission with oil to the correct level. See the Operation And Maintenance Manual.Disassemble And Assemble Transmission Oil Pump (Direct Drive)
Start By:a. remove transmission oil pump Mark the location of all components for assembly. 1. Remove locknut (3) and washer and drive gear (1) from the transmission oil pump. Remove O-ring seal (2). 2. Remove key (4) from the gear assembly. Remove four bolts (5), and set the pump assembly on blocks. 3. Remove the O-ring seal and cover (6) from the pump. Remove two gears (7). 4. Remove key (9) from the gear assembly. Remove body (8). 5. Remove two gears (11) and the key from gear assembly (10). Remove body assembly (12). Remove the O-ring seal from body (12). 6. Remove bearings (13) and dowels (14) from body assembly (12) if necessary. 7. Remove two gear assemblies (10) from body assembly (15). 8. Remove two bearings (16) and the O-ring seal from body assembly (15). The following steps are for assembly of the transmission oil pump.9. Check all parts for wear or damage, and replace them if necessary. Lubricate all parts with clean transmission oil during assembly. 10. Use tooling (A), and install two bearings (16) into body assembly (15) and two bearings (13) into body assembly (12). Install the bearings until they are 1.5 0.5 mm (.06 .02 in.) below the surface. Make sure the bearing joints are 30° 15° from the centerline toward the discharge port as shown.11. If four dowels (14) were removed, install them until they project 5.00 0.5 mm (.197 .02 in.) from the surface of body assembly (12).12. Install the O-ring seal in body assembly (15).13. Put body assembly (15) in position on blocks. Install drive gear assemblies (10) into body assembly (15).14. Install body assembly (12) on body assembly (15). Install the key on drive gear assembly (10), and install two gears (11). Install the O-ring seal in body assembly (12).15. Install body (8) on body assembly (12). Install key (9) into drive gear assembly (10).16. Install two gears (7) on the gear assemblies. Install the O-ring seal in cover (6), and put cover (6) in position on body (8).17. Carefully lay the pump assembly on its side, and install four bolts (5). Install key (4) on the gear assembly, and install O-ring seal (2) on the pump.18. Install gear (1), the washer and locknut (3). Tighten locknut (3) to a torque of 95 15 N m (70 11 lb. ft.).19.

Caterpillar parts catalog:

Caterpillar parts catalog
D337 MARINE ENGINE 23B00300-00455

Parts spring Caterpillar catalog:

225, D326F, D337, D337F, D342, D375D, D397D
44, D326F, D337, D337F, D342, D342C, D8H
D326F, D337, D337F, D342, D342C, D8H
D326F, D337, D337F, D342, D375D, D397D
12E, 140, 44, 46, 6A, 7A, 8 SR, 8A, 977K, 983, D320A, D337, D342C, D353C, D5, D6C, D8H, D9H
651, D326F, D337
D326F, D337, D337F
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.