2S7235 SPRING-GUIDE Caterpillar parts
1140, 1160, 16, 1673C, 1674, 1676, 1693, 225, 3160, 3304, 3306, 3408, 3412, 561C, 613, 621, 621R, 623, 627, 631C, 633C, 637D, 641B, 650B, 657B, 772, 814, 824B, 826B, 941, 943, 950, 955K, 966C, 977K, 9...
Rating:
Alternative (cross code) number:
CA2S7235
2S-7235
2S7235
CA2S7235
2S-7235
2S7235
Weight: 0.01 pounds 0 kg.
Information:
ACTUAL RATE
.2223
N/MM
FREE LENGTH
17.272
mm
OD
10.16
mm
SOLID LENGTH
6.2992
mm
WIRE DIAMETER
.635
mm
EXCAVATOR, WHEEL TRACTOR,
Compatible equipment models: 2S7235:
Number on catalog scheme:
52
For full view, you need register
Information:
System Operation Description:The possible causes of this failure are listed below:
The ignition switch is faulty.
Additional circuits are connected to the "S" terminal.
The solenoid of the starting motor is faulty.Test Step 1. TEST THE IGNITION SWITCH
Use the electrical schematic to locate the "start" terminal of the ignition switch.
Measure the voltage at the "start" terminal while the switch is in the "run" position.Expected Result:The voltage should be 0 Volts.Results:
OK - The voltage is 0 Volts. The ignition switch is operating properly. Proceed to test step 2.
NOT OK - The voltage is not 0 Volts. The ignition switch is not correct.Repair: Replace the ignition switch. Stop.Test Step 2. CHECK FOR ADDITIONAL CIRCUITS AT THE "S" TERMINAL
Locate the "S" terminal of the starter solenoid.
Check for additional circuits at the "S" terminal.
Remove any additional circuits.Expected Result:The starter does not operate properly.Results:
YES - The starter does NOT operate properly. The additional circuits are not the cause of the failure. Proceed to test step 3.
NO - The starter operates properly. The additional circuits are causing the solenoid to latch.Repair: Find an alternative power source for the additional circuits. Stop.Test Step 3. TEST THE SOLENOID OF THE STARTING MOTOR
Remove the starting motor.
Perform the solenoid tests. See Testing and Adjusting, "Starting Motor Solenoid - Test".Expected Result:The solenoid is correct.Results:
OK - The starting motor solenoid is correct. Proceed to test step 4.
NOT OK - The solenoid is incorrect. Replace the solenoid. Stop.Test Step 4. CHECK FOR SHORT TO +BATTERY
Disconnect the wire from the "Start" terminal of the ignition switch.
Disconnect the wire from the "S" terminal of the solenoid.
Measure the voltage from disconnected wire of the solenoid to ground.Expected Result:The voltage should be 0 Volts.Results:
OK - The voltage is 0 Volts. An intermittent problem is present.Repair: Exit this procedure. Perform this procedure again. Look for a recurrence of the problem. Stop.
NOT OK - The voltage is greater than 0 Volts. The start relay has failed or a short is present.Repair: Use the electrical schematic of the machine to test the wiring. Test the wiring between the start switch and the solenoid. If the wiring is correct replace the start relay. Stop.
The ignition switch is faulty.
Additional circuits are connected to the "S" terminal.
The solenoid of the starting motor is faulty.Test Step 1. TEST THE IGNITION SWITCH
Use the electrical schematic to locate the "start" terminal of the ignition switch.
Measure the voltage at the "start" terminal while the switch is in the "run" position.Expected Result:The voltage should be 0 Volts.Results:
OK - The voltage is 0 Volts. The ignition switch is operating properly. Proceed to test step 2.
NOT OK - The voltage is not 0 Volts. The ignition switch is not correct.Repair: Replace the ignition switch. Stop.Test Step 2. CHECK FOR ADDITIONAL CIRCUITS AT THE "S" TERMINAL
Locate the "S" terminal of the starter solenoid.
Check for additional circuits at the "S" terminal.
Remove any additional circuits.Expected Result:The starter does not operate properly.Results:
YES - The starter does NOT operate properly. The additional circuits are not the cause of the failure. Proceed to test step 3.
NO - The starter operates properly. The additional circuits are causing the solenoid to latch.Repair: Find an alternative power source for the additional circuits. Stop.Test Step 3. TEST THE SOLENOID OF THE STARTING MOTOR
Remove the starting motor.
Perform the solenoid tests. See Testing and Adjusting, "Starting Motor Solenoid - Test".Expected Result:The solenoid is correct.Results:
OK - The starting motor solenoid is correct. Proceed to test step 4.
NOT OK - The solenoid is incorrect. Replace the solenoid. Stop.Test Step 4. CHECK FOR SHORT TO +BATTERY
Disconnect the wire from the "Start" terminal of the ignition switch.
Disconnect the wire from the "S" terminal of the solenoid.
Measure the voltage from disconnected wire of the solenoid to ground.Expected Result:The voltage should be 0 Volts.Results:
OK - The voltage is 0 Volts. An intermittent problem is present.Repair: Exit this procedure. Perform this procedure again. Look for a recurrence of the problem. Stop.
NOT OK - The voltage is greater than 0 Volts. The start relay has failed or a short is present.Repair: Use the electrical schematic of the machine to test the wiring. Test the wiring between the start switch and the solenoid. If the wiring is correct replace the start relay. Stop.
Cat SIS web machinery list:
Parts spring Caterpillar catalog:
518, 518C, 530B, 920, 930, 950, 966C
16, 814F, 814F II, 815B, 815F, 815F II, 816F, 816F II, 826C, 834B, 836, 936, 950, 950F, 950F II, 950G, 950G II, 950H, 950K, 960F, 962G, 962G II, 962H, 962K, 966C, 966F, 966F II, 966G, 966G II, 966H, 9...
814, 815, 826B, 920, 930, 950, 960F, 966C, 966R, 992
772, 773, 825C, 826C, 980C, 992, 992C, 992D
772, 773, 825C, 826C, 834B, 980C, 988B, 988F, 992, 992C, 992D, R2900, R2900G, R3000H
120G, 12G, 130G, 140G, 14G, 14H, 14H NA, 160G, 16G, 16H, 16H NA, 988B, 992C, 994
814, 966C, 966R, 980, 980B
120G, 12G, 130G, 140G, 14G, 160G, 16G, 992, FB518
824B, 826B, 834, 988, 992
950
950
120G, 12G, 130G, 140G, 160G, 769, 772
3304, 3306, 3406, 3408, 3408B, 3412, D320A, D343, G3306, G342C
3304, 3306, 3406, 3406B, 3408, 3408B, 3412, G3306, G3406, G3408, G3412, G342C
3304, 3306, 3406, 3406B, 3408, 3408B, 3412, G3306, G3406, G3408, G3412, G342C
7N6052
SPRING AS-SPEED
3304, 3306, 3406, 3406B, 3408, 3408B, 3412, G3306, G3406, G3408, G3412, G342C
3304, 3306, 3406, 3406B, 3408, 3408B, 3412, G3306, G3406, G3408, G3412, G342C
120G, 14G, 245, 3408, 3408B, 3412, D10, D353C, D4D, D6C, D7F, D9H, D9L
120, 16, 1673C, 1674, 1676, 1693, 16G, 245, 3304, 3306, 3406, 3408, 3408B, 3408C, 3412, 3412C, 3412D, 561C, 589, 621, 621B, 621R, 623, 627, 631C, 631E, 637D, 637E, 641B, 650B, 651E, 657B, 657E, 769C, ...
8N6579
SPRING
3408, 3408B, 3408C, 3412, 3412C, 3412D, 631E, 633D, 637D, 637E, 769C, 771C, 773B, 775B, 834B, 988B, 988F, PM-565
3408, 3408B, 3408C, 3412, 3412C, 3412D, 631E, 633D, 637D, 637E, 769C, 771C, 773B, 775B, 834B, 988B, 988F, PM-565
6I1103
SPRING AS
3304, 3304B, 3306, 3306B, 3406, 3406B, 3406C, 3408, 3408C, 3412, 3412C, G3406, G3408, G3408B, G3412
3304, 3304B, 3306, 3306B, 3406, 3406B, 3406C, 3408, 3408C, 3412, 3412C, G3406, G3408, G3408B, G3412
6N4460
SPRING-LEAF
3408, 3412, 631E, 637D, 637E, 651E, 657E, 769C, 771C, 834B, PM-565
3408, 3412, 631E, 637D, 637E, 651E, 657E, 769C, 771C, 834B, PM-565
2N5625
SPRING-LEAF
3408, 3412, 641B, 772, 777, 992, D10, D348
3408, 3412, 641B, 772, 777, 992, D10, D348
120, 16, 1673, 1673B, 1673C, 1674, 1676, 1693, 16G, 245, 3304, 3306, 3406, 3408, 3412, 561C, 621, 621B, 621R, 623, 627, 631C, 633C, 637D, 641B, 650B, 651E, 657B, 657E, 768B, 772, 777, 814, 824B, 826B,...