5H9475 SPRING Caterpillar parts
227, 572G, 977D, 977H
Rating:
Alternative (cross code) number:
CA5H9475
5H-9475
5H9475
CA5H9475
5H-9475
5H9475
Weight: 35 pounds 15 kg.
Information:
ACTUAL RATE
217.124
N/MM
FREE LENGTH
558.8
mm
OD
127
mm
SOLID LENGTH
345.281
mm
WIRE DIAMETER
23.622
mm
LOGGER, TRACK LOADER,
Information:
C18 Engine Fitting Installation (without Ball Valves)
Illustration 6 g02556316
Install the new 347-4444 Adapter (10) into the rear of the oil cooler bonnet. Refer to Illustration 6. Apply Loctite sealant on the connector threads and torque the connector to 75 N m (55 lb ft).
Install the new 357-4579 Connector and 6V-6609 O-Ring Seal into the front engine port. Refer to Illustration 3. Torque the connector to 60 N m (44 lb ft).
Illustration 7 g02556521
Install 9R-3253 bracket (11) on the oil cooler. Remove the existing bolt and replace the bolt with the longer 0T-0055 Bolt (12) to hold the bracket in place. Refer to Illustration 7.
Proceed to "Heater Installation".C18 Engine Fitting Installation (with Ball Valves)
Install the new 6V-2492 Connectors into the existing valves. Apply Loctite sealant on the connector threads and torque the connector to 60 N m (44 lb ft). Be careful not to turn the existing fittings and break the seals.
Proceed to "Heater Installation".Heater Installation
Cut a 1.3 m (4.3 ft) piece of the silicone 302-7411 Hose .Note: For C15 on a wide base cut the hose 1.6 m (5.2 ft) long. Slide two 5P-7854 Clips into middle of the longer supply hose, and two 7X-7958 Hose Clamps , one on each end of the hose.
Push the hose on the front engine block connector. Do not torque the hose clamp yet.
Cut a 0.7 m (2.3 ft) long piece of the silicone 302-7411 Hose . Slide two 7X-7958 Hose Clamps , one on each end of the hose.Note: For C15 on a wide base cut the hose 0.8 m (2.6 ft) long and slide one hose clip 5P-7854 Clip into the middle of this hose.
Slide the hose on the rear engine connector. Do not torque the hose clamp yet.
Mount the heater to the new bracket 336-8586 Bracket reusing the heater mounting U-bolt clamps and hardware.Note: For C18 wide base gensets use 362-1639 Bracket . Make sure that the heater outlet connector is tilted 6 degrees from vertical and toward the engine.
Determine the best location for the new heater with the new bracket. The bracket will mount to the top of the genset base rail. Place the new heater in a location on the base rail that does not obstruct any installed equipment. Also ensure that the hoses can be routed to the heater inlet and outlet.
Illustration 8 g02556996
Mark the holes for the bracket in the base rail (13). Drill four 12 mm (0.47 inch) holes in the base rail. Refer to Illustration 8.
Install the new heater bracket on the genset base rail using 8T-4195 Bolts , 8T-4133 Nuts , and 8T-4121 Hard Washers .
Illustration 9 g02557057
Slide the 4D-7388 Clip (14) already on the hose to match the hole in the oil cooler 9R-3253 Plate (6), and attach this plate using 8T-4195 Bolts (15), 8T-4133 Nuts (17), and 8T-4121 Hard Washers (16). Refer to Illustration 9.Note: Omit this step if retaining the existing ball valves.
Route the supply hose to the heater
Illustration 6 g02556316
Install the new 347-4444 Adapter (10) into the rear of the oil cooler bonnet. Refer to Illustration 6. Apply Loctite sealant on the connector threads and torque the connector to 75 N m (55 lb ft).
Install the new 357-4579 Connector and 6V-6609 O-Ring Seal into the front engine port. Refer to Illustration 3. Torque the connector to 60 N m (44 lb ft).
Illustration 7 g02556521
Install 9R-3253 bracket (11) on the oil cooler. Remove the existing bolt and replace the bolt with the longer 0T-0055 Bolt (12) to hold the bracket in place. Refer to Illustration 7.
Proceed to "Heater Installation".C18 Engine Fitting Installation (with Ball Valves)
Install the new 6V-2492 Connectors into the existing valves. Apply Loctite sealant on the connector threads and torque the connector to 60 N m (44 lb ft). Be careful not to turn the existing fittings and break the seals.
Proceed to "Heater Installation".Heater Installation
Cut a 1.3 m (4.3 ft) piece of the silicone 302-7411 Hose .Note: For C15 on a wide base cut the hose 1.6 m (5.2 ft) long. Slide two 5P-7854 Clips into middle of the longer supply hose, and two 7X-7958 Hose Clamps , one on each end of the hose.
Push the hose on the front engine block connector. Do not torque the hose clamp yet.
Cut a 0.7 m (2.3 ft) long piece of the silicone 302-7411 Hose . Slide two 7X-7958 Hose Clamps , one on each end of the hose.Note: For C15 on a wide base cut the hose 0.8 m (2.6 ft) long and slide one hose clip 5P-7854 Clip into the middle of this hose.
Slide the hose on the rear engine connector. Do not torque the hose clamp yet.
Mount the heater to the new bracket 336-8586 Bracket reusing the heater mounting U-bolt clamps and hardware.Note: For C18 wide base gensets use 362-1639 Bracket . Make sure that the heater outlet connector is tilted 6 degrees from vertical and toward the engine.
Determine the best location for the new heater with the new bracket. The bracket will mount to the top of the genset base rail. Place the new heater in a location on the base rail that does not obstruct any installed equipment. Also ensure that the hoses can be routed to the heater inlet and outlet.
Illustration 8 g02556996
Mark the holes for the bracket in the base rail (13). Drill four 12 mm (0.47 inch) holes in the base rail. Refer to Illustration 8.
Install the new heater bracket on the genset base rail using 8T-4195 Bolts , 8T-4133 Nuts , and 8T-4121 Hard Washers .
Illustration 9 g02557057
Slide the 4D-7388 Clip (14) already on the hose to match the hole in the oil cooler 9R-3253 Plate (6), and attach this plate using 8T-4195 Bolts (15), 8T-4133 Nuts (17), and 8T-4121 Hard Washers (16). Refer to Illustration 9.Note: Omit this step if retaining the existing ball valves.
Route the supply hose to the heater
Caterpillar parts catalog:
Parts spring Caterpillar catalog:
7H2445
SPRING
561B, 561C, 951B, 955C, 955H, 977D, D5
561B, 561C, 951B, 955C, 955H, 977D, D5
5M5731
SPRING
12E, 651, 977H, D4D
12E, 651, 977H, D4D
6B9633
SPRING (OUTER)
561B, 561C, 977D, 977H, D5
561B, 561C, 977D, 977H, D5
4F5003
SPRING ASSEM.
571G, 572G, 583K, 594, 594H, 977D, 977H, 977K, 977L, 983, 983B, D7F, D7G, D7G2, D8H, D8K, D9E, D9G, D9H
571G, 572G, 583K, 594, 594H, 977D, 977H, 977K, 977L, 983, 983B, D7F, D7G, D7G2, D8H, D8K, D9E, D9G, D9H
1K3165
SPRING
571G, 572G, 583H, 594
571G, 572G, 583H, 594
5M2059
SPRING
528, 572G, 983, 983B, D7F, D7G, D7G2
528, 572G, 983, 983B, D7F, D7G, D7G2
3P1885
SPRING
227, 571G, 572G, 973, 977K, 977L, D7F, D7G, D7G2
227, 571G, 572G, 973, 977K, 977L, D7F, D7G, D7G2
5M2058
SPRING
572G, 983B, D7F, D7G
572G, 983B, D7F, D7G
9H5536
SPRING
14E, 572G, D7F, D7G, D7G2, D8H
14E, 572G, D7F, D7G, D7G2, D8H
1J9533
SPRING
163, 183, 623, 631C, 633C, 633D, 637D, 639D, 641, 641B, 651, 657, 814, 824B, 824C, 834, 834B, 950, 966C, 966D, 966F, 966F II, 970F, 977H, 980B, 980C, 980F, 988, 988B, 988F, 988F II, 992, 992C, 992D, A...
163, 183, 623, 631C, 633C, 633D, 637D, 639D, 641, 641B, 651, 657, 814, 824B, 824C, 834, 834B, 950, 966C, 966D, 966F, 966F II, 970F, 977H, 980B, 980C, 980F, 988, 988B, 988F, 988F II, 992, 992C, 992D, A...
5H9474
SPRING
977D, 977H
977D, 977H
7M2923
SPRING (OUTER)
621, 631C, 651, 657, 824B, 834, 977H, 988
621, 631C, 651, 657, 824B, 834, 977H, 988
4D9626
SPRING
16, 561D, 768B, 769, 772, 773, D4H, D5B, D5H
16, 561D, 768B, 769, 772, 773, D4H, D5B, D5H
1V8274
SPRING 4.90 m(193 in.)
955K, 955L
955K, 955L
4M7980
SPRING
140G, 14G, 16G, 955L, 977L, 983B, D25D
140G, 14G, 16G, 955L, 977L, 983B, D25D
3G5035
SPRING
613B, 613C, 613C II, D3
613B, 613C, 613C II, D3
3G3827
SPRING
977L
977L
3G9192
SPRING
941
941
9J5698
SPRING
D10, D8K, D9H
D10, D8K, D9H
9J5696
SPRING
824C, 824G, 824G II, 824H, 825G, 825G II, 825H, 966G, 966G II, 966H, 966K, 966M XE, 972G, 972G II, 972H, 972M XE, 980C, 980G, 980G II, D10, D8K, D9H
824C, 824G, 824G II, 824H, 825G, 825G II, 825H, 966G, 966G II, 966H, 966K, 966M XE, 972G, 972G II, 972H, 972M XE, 980C, 980G, 980G II, D10, D8K, D9H
9G3491
SPRING
5110B, 561D, D5B
5110B, 561D, D5B
3F6142
SPRING
814B, 815B, 955L, 977L, 983B
814B, 815B, 955L, 977L, 983B