1254403 SPROCKET Caterpillar parts
323D L, 325D, 329D L, 345C L, OEMS
Rating:
Alternative (cross code) number:
CA1254403
125-4403
1254403
CA1254403
125-4403
1254403
Weight: 99 pounds 44 kg.
MOBILE HYD POWER UNIT, UNDERCARRIAGE,
Compatible equipment models: 1254403:
Information:
Adjustment Procedure - Implement Discharge Pressure
Illustration 6 g03664394
(18) Implement discharge pressure port
(19) Implement pilot pressure tap
(20) Implement load sense pressure tap
Illustration 7 g03664396
(H) Main implement valve
(J) Load sense relief valve
Locate the load sense relief valve (J) on the main implement valve (H). Best practice is to access the valve from the right side of the machine in the hitch.
Use a hex wrench to loosen the lock-nut and an internal hex to adjust the implement load sense pressure. Turn inwards to increase the pressure or outwards to decrease the pressure. Note: The final pressure adjustment must be inward to increase pressure. If the setting is too high, adjust the pressure down below the target pressure. Then, increase the pressure to reach the final setting.
Tighten the lock-nut and retest the implement discharge pressure to verify setting. Test Preparation - Implement Load Sense Pressure
Load sense pressure can be checked in the same way as implement discharge pressure. Checking the load sense pressure will provide an accurate reading of the pressure signal that is being sent to the implement pump.Ensure that pilot pressures are set before proceeding.
Ensure that the steering lock is engaged.
Ensure that the oil temperature is at least 60° C (140° F)
Ensure that ride control is set to OFF.
Attach a pressure gauge to the implement load sense gauge port (20). Refer to Illustration 8. Test Procedure - Implement Load Sense Pressure
Start the engine and set to high idle.
With the engine in high idle, raise the linkage and allow the linkage to stall in the raise position. Check gauge reading. Refer to Table 1 for specifications.
If pressure is correct, lower linkage and stop engine. Properly purge the system and disconnect the gauge. If the pressure is not within specifications, refer to the "Adjustment Procedure - Implement Load Sense Pressure" section. Adjustment Procedure - Implement Load Sense Pressure
Illustration 8 g03664394
(19) Implement pilot pressure tap
(20) Implement load sense pressure tap
Illustration 9 g03664396
(H) Main implement valve
(J) Load sense relief valve
Locate the load sense relief valve (J) on the main implement valve (H). Best practice is to access the valve from the right side of the machine in the hitch.
Use a hex wrench to loosen the lock-nut and an internal hex to adjust the implement load sense pressure. Turn inwards to increase the pressure or outwards to decrease the pressure. Note: The final pressure adjustment must be inward to increase pressure. If the setting is too high, adjust the pressure down below the target pressure. Then, increase the pressure to reach the final setting.
Tighten the lock-nut and retest the implement load sense pressure to verify setting. Test Preparation - Implement Pump Margin Pressure
Margin pressure can be checked to troubleshoot hydraulic issues. The implement pump margin pressure is the difference between the implement pump load sense pressure and the implement pump discharge pressure. When a load sense signal is sent to the pump, the controller adds some margin pressure on top of the signal.
Two high-pressure gauges or a differential gauge is required to check the margin pressure.
Take note that the
Illustration 6 g03664394
(18) Implement discharge pressure port
(19) Implement pilot pressure tap
(20) Implement load sense pressure tap
Illustration 7 g03664396
(H) Main implement valve
(J) Load sense relief valve
Locate the load sense relief valve (J) on the main implement valve (H). Best practice is to access the valve from the right side of the machine in the hitch.
Use a hex wrench to loosen the lock-nut and an internal hex to adjust the implement load sense pressure. Turn inwards to increase the pressure or outwards to decrease the pressure. Note: The final pressure adjustment must be inward to increase pressure. If the setting is too high, adjust the pressure down below the target pressure. Then, increase the pressure to reach the final setting.
Tighten the lock-nut and retest the implement discharge pressure to verify setting. Test Preparation - Implement Load Sense Pressure
Load sense pressure can be checked in the same way as implement discharge pressure. Checking the load sense pressure will provide an accurate reading of the pressure signal that is being sent to the implement pump.Ensure that pilot pressures are set before proceeding.
Ensure that the steering lock is engaged.
Ensure that the oil temperature is at least 60° C (140° F)
Ensure that ride control is set to OFF.
Attach a pressure gauge to the implement load sense gauge port (20). Refer to Illustration 8. Test Procedure - Implement Load Sense Pressure
Start the engine and set to high idle.
With the engine in high idle, raise the linkage and allow the linkage to stall in the raise position. Check gauge reading. Refer to Table 1 for specifications.
If pressure is correct, lower linkage and stop engine. Properly purge the system and disconnect the gauge. If the pressure is not within specifications, refer to the "Adjustment Procedure - Implement Load Sense Pressure" section. Adjustment Procedure - Implement Load Sense Pressure
Illustration 8 g03664394
(19) Implement pilot pressure tap
(20) Implement load sense pressure tap
Illustration 9 g03664396
(H) Main implement valve
(J) Load sense relief valve
Locate the load sense relief valve (J) on the main implement valve (H). Best practice is to access the valve from the right side of the machine in the hitch.
Use a hex wrench to loosen the lock-nut and an internal hex to adjust the implement load sense pressure. Turn inwards to increase the pressure or outwards to decrease the pressure. Note: The final pressure adjustment must be inward to increase pressure. If the setting is too high, adjust the pressure down below the target pressure. Then, increase the pressure to reach the final setting.
Tighten the lock-nut and retest the implement load sense pressure to verify setting. Test Preparation - Implement Pump Margin Pressure
Margin pressure can be checked to troubleshoot hydraulic issues. The implement pump margin pressure is the difference between the implement pump load sense pressure and the implement pump discharge pressure. When a load sense signal is sent to the pump, the controller adds some margin pressure on top of the signal.
Two high-pressure gauges or a differential gauge is required to check the margin pressure.
Take note that the
Cat SIS web machinery list:
Parts sprocket Caterpillar catalog:
1028134
SPROCKET-TRACK
311, 312, 312B, 315, 315B, 315B L, 317, 317B LN, 318B, OEMS
311, 312, 312B, 315, 315B, 315B L, 317, 317B LN, 318B, OEMS
8E9805
SPROCKET-TRACK
311C, 313D2 LGP, 315C, 315D L, 316E L, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR,...
311C, 313D2 LGP, 315C, 315D L, 316E L, 318B, 318C, 318D L, 318D2 L, 318E L, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320C FM, 320C L, 320D, 320D FM, 320D GC, 320D L, 320D LN, 320D LRR, 320D RR,...
6Y4898
SPROCKET-TRACK
1090, 2290, 320B, 320C, 322B L, 322C, 322C FM, 323D LN, 323D SA, 323E L, 324D FM, 324D FM LL, 325, 325 L, 325 LN, 325B, 325B L, 325C, 325C FM, 325D, 325D L, 325D MH, 329D, 329D L, 329D LN, 329E, 329E ...
1090, 2290, 320B, 320C, 322B L, 322C, 322C FM, 323D LN, 323D SA, 323E L, 324D FM, 324D FM LL, 325, 325 L, 325 LN, 325B, 325B L, 325C, 325C FM, 325D, 325D L, 325D MH, 329D, 329D L, 329D LN, 329E, 329E ...
6Y5685
SPROCKET-TRACK
1290T, 1390, 2491, 2590, 325C, 328D LCR, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E H...
1290T, 1390, 2491, 2590, 325C, 328D LCR, 330, 330 FM L, 330 L, 330B, 330B L, 330C, 330C FM, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E H...
9Q5693
SPROCKET GP
OEMS
OEMS
1528653
SPROCKET GP
OEMS
OEMS
1302463
SPROCKET
OEMS
OEMS
9Q5420
SPROCKET
OEMS
OEMS
1634944
SPROCKET-TRACK
330D, 345C L, 345D, 349D L
330D, 345C L, 345D, 349D L
1243296
SPROCKET-TRACK
330C, 330D L, 330D MH, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 365C L
330C, 330D L, 330D MH, 345B, 345B II, 345B II MH, 345B L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 349E, 349E L, 349E L HVG, 349E L VG, 349F L, 365C L
1276738
SPROCKET AS
345B II, 345B L, 345C, 345C L
345B II, 345B L, 345C, 345C L
1302463
SPROCKET
OEMS
OEMS
1528653
SPROCKET GP
OEMS
OEMS
9Q5693
SPROCKET GP
OEMS
OEMS
1C7093
SPROCKET
OEMS
OEMS
1060418
SPROCKET
330, 330 FM L, OEMS
330, 330 FM L, OEMS
8W8332
SPROCKET
14G, 14H, 14H NA
14G, 14H, 14H NA
8W8286
SPROCKET
120G, 120H, 120H ES, 120H NA
120G, 120H, 120H ES, 120H NA
9D4207
SPROCKET
12G, 130G, 140G, 14G, 16G
12G, 130G, 140G, 14G, 16G
7D8354
SPROCKET
12G, 12H, 12H ES, 12H NA, 12K, 130G, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 160G
12G, 12H, 12H ES, 12H NA, 12K, 130G, 140G, 140H, 140H ES, 140H NA, 140K, 140K 2, 143H, 160G
1413911
SPROCKET-TRACK
330C, 330D, 330D L, 336D L, 336D LN, 336E, 345D, 349D L, OEMS
330C, 330D, 330D L, 336D L, 336D LN, 336E, 345D, 349D L, OEMS
9Q5420
SPROCKET
OEMS
OEMS