2558095 SPROCKET-TRACK Caterpillar parts
D6K, D6K LGP, D6K XL, PL61
Rating:
Alternative (cross code) number:
CA2558095
255-8095
2558095
CA2558095
255-8095
2558095
Weight: 91 pounds 41 kg.
PIPELAYER, TRACK-TYPE TRACTOR,
This part in 2 request:
Show.
This information for suppliers only!
2022-12-27
2018-01-11
Compatible equipment models: 2558095:
Information:
Removal Procedure
Illustration 1 g01248557
Illustration 2 g01248562
Loosen screws (1) on the cover of panel (3). Open the cover in order to gain access to the back of service meter (2).
Place an identification mark on all of the harness assemblies for the installation procedure.
Remove the nuts and the harness assemblies from the bracket. Remove the bracket and service meter (2) from panel (3).
Remove the clip and disconnect connector (4). Loosen locknut (5) and remove sensor (6). Installation Procedure
Illustration 3 g01248562
Illustration 4 g01248557
Install the bracket, the nuts, and service meter (2) in panel (3).
Install sensor (6) until the sensor touches the tooth of the flywheel ring gear. Turn the sensor in the counterclockwise direction for 1/2 turn. Tighten locknut (5) to a torque of 45 7 N m (33 5 lb ft). The clearance of the sensor and the flywheel ring gear should be 0.69 0.14 mm (0.027 0.006 inch).
Install connector (4) and install the clip.
Close the cover and tighten screws (1).
Illustration 1 g01248557
Illustration 2 g01248562
Loosen screws (1) on the cover of panel (3). Open the cover in order to gain access to the back of service meter (2).
Place an identification mark on all of the harness assemblies for the installation procedure.
Remove the nuts and the harness assemblies from the bracket. Remove the bracket and service meter (2) from panel (3).
Remove the clip and disconnect connector (4). Loosen locknut (5) and remove sensor (6). Installation Procedure
Illustration 3 g01248562
Illustration 4 g01248557
Install the bracket, the nuts, and service meter (2) in panel (3).
Install sensor (6) until the sensor touches the tooth of the flywheel ring gear. Turn the sensor in the counterclockwise direction for 1/2 turn. Tighten locknut (5) to a torque of 45 7 N m (33 5 lb ft). The clearance of the sensor and the flywheel ring gear should be 0.69 0.14 mm (0.027 0.006 inch).
Install connector (4) and install the clip.
Close the cover and tighten screws (1).
Caterpillar parts catalog:
Parts sprocket Caterpillar catalog:
4V4106
SPROCKET AS-TRACK
941, D4E, D4E SR
941, D4E, D4E SR
0968047
SPROCKET
311, E110B, E140
311, E110B, E140
5W7281
SPROCKET
205, 213B
205, 213B
8E1882
SPROCKET
205B, 211B
205B, 211B
6C3495
SPROCKET AS
215C
215C
9C2646
SPROCKET-TRACK
225D, 229
225D, 229
5S4826
SPROCKET ASSEM. (STD)
561C, D5
561C, D5
1K3412
SPROCKET
561D, 571G
561D, 571G
2589787
SPROCKET-TRACK
D3K XL, D3K2 LGP, D4K XL, D4K2 XL
D3K XL, D3K2 LGP, D4K XL, D4K2 XL