3335622 SPROCKET Caterpillar parts
305.5E, 306, 306E
Rating:
Alternative (cross code) number:
CA3335622
333-5622
3335622
CA3335622
333-5622
3335622
Weight: 33 pounds 15 kg.
MINI HYD EXCAVATOR,
Information:
5N1955 ELECTRONIC SPEED SWITCH
1. Verify button. 2. Reset button. 3. "LED" overspeed light. 4. Seal screw plug (overspeed). 5. Seal screw plug (crank terminate). 6. Seal screw plug (oil step).Oil Step Calibration
1. Remove the lockwire and seal from seal screw plugs (4), (5) and (6). Remove seal screw plug (6) from access hole for the oil step adjustment screw.2. Use a small screwdriver and lightly turn oil step adjustment potentiometer 20 turns in the direction opposite of "MAX ARROW" (counterclockwise). This will lower the oil step speed setting to its lowest value. The oil step adjustment screw is made so it can not cause damage to the potentiometer, or be removed, if the adjustment screw is turned too many turns in either direction.3. Use a 6V3030 Multimeter (or a voltmeter of same accuracy) to check for positive (+) voltage at terminal ESS-13 [negative (-) voltage is at terminal ESS-5].4. Make reference to SPEED SPECIFICATION CHART (Part of PROCEDURE D). For a particular engine rating, find the specified rpm in column for Oil Step Speed Setting. Run the engine at this specified rpm.5. With the engine running, look into the oil step adjustment access hole. A red "LED" (light emitting diode) light will be on. After an 8 to 10 second delay, positive (+) voltage will be seen at terminal ESS-13. Now turn the oil step adjustment potentiometer clockwise until the red light in the oil step access hole goes out. When the light goes out, this indicates that the oil step rpm setting is above the present running rpm of the engine. Slowly turn the adjustment potentiometer counterclockwise until the light comes back on. After an 8 to 10 second delay, positive (+) voltage will be seen at terminal ESS-13.6. When the oil step setting is correct, install seal screw plug (6) into the adjustment access hole for the oil step function. Tighten plug to a torque of 0.20 0.03 N m (2 .3 lb. in.). If all other adjustments are complete (overspeed and crank terminate), install lockwire and seal.
Caterpillar parts catalog:
Parts sprocket Caterpillar catalog:
1584752
SPROCKET GP
304C CR, 305.5, 305D CR, 305E, 306
304C CR, 305.5, 305D CR, 305E, 306
3335621
SPROCKET GP
305.5E, 306, 306E
305.5E, 306, 306E
1584795
SPROCKET
304, 304.5, 304C CR, 305, 305.5, 305D CR, 305E, 306
304, 304.5, 304C CR, 305, 305.5, 305D CR, 305E, 306
1905761
SPROCKET
305.5, 306, 307C, 307D, 308C, 308D
305.5, 306, 307C, 307D, 308C, 308D
2948262
SPROCKET-TRACK
307D, 307E, 308D, 308E, 308E CR, 308E SR, 308E2 CR
307D, 307E, 308D, 308E, 308E CR, 308E SR, 308E2 CR
2606341
SPROCKET
304C CR, 305.5D, 305.5E, 305C CR
304C CR, 305.5D, 305.5E, 305C CR
2645371
SPROCKET
303.5C, 303.5D, 303.5E, 303C CR, 304D CR, 304E
303.5C, 303.5D, 303.5E, 303C CR, 304D CR, 304E
1937091
SPROCKET
303, 303E CR
303, 303E CR
1309326
SPROCKET-TRACK
307B, 307C, 308C
307B, 307C, 308C
1905761
SPROCKET
305.5, 306, 307C, 307D, 308C, 308D
305.5, 306, 307C, 307D, 308C, 308D
8K4054
SPROCKET
235D, 245
235D, 245
8K2743
SPROCKET
225, 235
225, 235
4262641
SPROCKET
302.2D
302.2D
3860584
SPROCKET
302.4D, 302.7D
302.4D, 302.7D
3813033
SPROCKET
301.4C, 301.7D, 301.7D CR
301.4C, 301.7D, 301.7D CR
3725983
SPROCKET
300.9D
300.9D