2916492 STABILIZER GP Caterpillar parts
M318D MH, M322D, M322D MH
Rating:
Alternative (cross code) number:
CA2916492
291-6492
2916492
CA2916492
291-6492
2916492
WHEELED EXCAVATOR,
Information:
Family Of Engines Equipped With Spacer PlatesReference: Engine News, December 1988, Page 4, "New Liner Seat Inserts Available".Reference: Special Instruction, Form SMHS8222, "Installation Of 2W3815 Or 5N0093 Inserts".New seat inserts are available to salvage engine blocks that have damage from fretting, erosion, corrosion, wear steps or cracks on top of the cylinder block under the cylinder liner flange. These new inserts provide greater flexibility and ease of repair by complementing the existing stainless steel inserts. See the chart.
The new inserts measure 0.05 mm (.002 in) thinner or thicker than the standard inserts. The nominal thickness is marked on each new insert. The new inserts provide additional repair options within each counterbore depth range. They also help alleviate the need to counterbore to the next available depth range if the original counterbore measures out of specifications.
Additionally, new thicker inserts are available for clean-up of deeper cracks in the liner seat [down to 5.26 mm (.207 in) deep]. Previously, Caterpillar recommended counterboring only to a depth of 2.71 mm (.106 in).
To ensure correct liner projection after counterboring, it is recommended that inserts be measured, to determine actual thickness, prior to machining.
Shims made from cast iron or any other material are not recommended for use on 3400 Family of Engines to adjust liner projection. Use only the approved inserts listed in the chart.
When machining is complete, deburr the edges of the counterbore with emery paper or No. 400 wet-dry sandpaper. Install the inserts in the counterbore with chamfered edge of the insert facing down and without sealant (dry).
Inserts previously installed in an engine can be used again in subsequent repairs if the inserts are measured at four locations for the correct thickness.
The new inserts measure 0.05 mm (.002 in) thinner or thicker than the standard inserts. The nominal thickness is marked on each new insert. The new inserts provide additional repair options within each counterbore depth range. They also help alleviate the need to counterbore to the next available depth range if the original counterbore measures out of specifications.
Additionally, new thicker inserts are available for clean-up of deeper cracks in the liner seat [down to 5.26 mm (.207 in) deep]. Previously, Caterpillar recommended counterboring only to a depth of 2.71 mm (.106 in).
To ensure correct liner projection after counterboring, it is recommended that inserts be measured, to determine actual thickness, prior to machining.
Shims made from cast iron or any other material are not recommended for use on 3400 Family of Engines to adjust liner projection. Use only the approved inserts listed in the chart.
When machining is complete, deburr the edges of the counterbore with emery paper or No. 400 wet-dry sandpaper. Install the inserts in the counterbore with chamfered edge of the insert facing down and without sealant (dry).
Inserts previously installed in an engine can be used again in subsequent repairs if the inserts are measured at four locations for the correct thickness.
Caterpillar SIS machinery equipment:
Caterpillar parts catalog:
Parts stabilizer Caterpillar catalog:
2603448
STABILIZER GP
M318D MH, M322D, M322D MH
M318D MH, M322D, M322D MH
2786992
STABILIZER GP
M318D MH, M322D MH
M318D MH, M322D MH
2603505
STABILIZER AR
M318D MH, M322D, M322D MH
M318D MH, M322D, M322D MH
3419158
STABILIZER AR
M322D
M322D
2603518
STABILIZER AR
M318D MH, M322D, M322D MH
M318D MH, M322D, M322D MH
2916494
STABILIZER GP
M318D MH, M322D, M322D MH
M318D MH, M322D, M322D MH
2238237
STABILIZER AR
TH460B, TH560B
TH460B, TH560B
2351827
STABILIZER AR
M316C, M318C
M316C, M318C
2343297
STABILIZER GP
M325C MH, M325D MH
M325C MH, M325D MH
2351825
STABILIZER AR
M313C
M313C
2194226
STABILIZER AR
TH460B, TH560B
TH460B, TH560B
2108918
STABILIZER AR
424D, 428D, 432D, 438D, 442D
424D, 428D, 432D, 438D, 442D