AVSPARE.COM
parts catalog

STACK AS-AIR 9Q3712 - Caterpillar


9Q3712 STACK AS-AIR Caterpillar parts 972G II, 980G
Rating:
34
Alternative (cross code) number:
CA9Q3712
9Q-3712
9Q3712
Caterpillar 9Q3712 STACK AS-AIR
Weight: 9 pounds 4 kg.

Buy STACK AS-AIR 9Q3712 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compatible equipment models: 9Q3712:

WHEEL LOADER  972G II   980G   Caterpillar
Number on catalog scheme: 3
  For full view, you need register

Information:


Illustration 1 g01006557
Schematic for the key start switchThe ECM activates the start relay when the key start switch is in the START position and the transmission direction control switch is in the NEUTRAL position. The ECM detects a failure in the circuit for the start relay and the electrical system. If CID 0638 or CID 0168 are present the diagnostic code must be corrected before performing the following procedure.Test Step 1. CHECK THE KEY START SWITCH IN THE START POSITION.
Make sure that a CID 0638 fault does not exist. If the fault exists, correct the fault before proceeding.
Disconnect the ECM from the machine harness.
Turn the disconnect switch to the ON position.
Turn and hold the key start switch in the START position.
At the machine harness connector for the ECM, measure the voltage between contact J1-40 (wire 307-OR) and frame ground.Expected Result:The +battery voltage should be present.Results:
YES - The +battery voltage is present. Proceed to Test Step 2.
NO - The +battery voltage is NOT present. The key start switch or the machine harness (wire 307-OR) has failed. Check the key start switch and the machine harness.Repair: If necessary, replace the key start switch and/or the machine harness. Stop.Test Step 2. CHECK THE KEY START SWITCH IN THE OFF POSITION.
The ECM remains disconnected from the machine harness.
Turn the key start switch to the OFF position.
At the machine harness connector for the ECM, measure the voltage between contact J1-40 (wire 307-OR) and frame ground.Expected Result:The +battery voltage should be present.Results:
YES - The +battery voltage is present. The key start switch or the machine harness (wire 307-OR) has failed. Check the key start switch and the machine harness.Repair: If necessary, replace the key start switch and/or the machine harness. Stop.
NO - The +battery voltage is NOT present. The harness circuit operates correctly. It is unlikely that the ECM has failed. Perform these Steps again.Repair: If the cause is not found, replace the ECM. Refer to Systems Operation, Troubleshooting, Testing And Adjusting, "Electronic Control Module (Power Train) - Replace" for the machine that is being serviced. Stop.

Caterpillar parts catalog:

Caterpillar parts catalog
980G 2Z-9623 Mill AR-Steel Custom Product Support Literature For 980G Wheel Loader 2KR00001-UP (MACHINE)
STEEL MILL OR THE 927GI / T951G/ AXC WHEEL LOADERS AXC00001-UP (MACHINE)


Parts stack Caterpillar catalog:

8S2385 STACK AS-AIR
245B, 589, 980G, 980G II, D8R, D8R II, D9R
3779327 STACK AS
834K, 836K, 988K
3468717 STACK AS
834K, 836K, 844K, 854K, 988K, 990K, 992K, 993K
1592791 STACK AS-EXHAUST
854G, 854K, 992G, 992K, 993K
1433669 STACK AS-EXHAUST
824G II, 825G II, 826G II, 834G, 834H, 836G, 988G, 988H
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.