STARTING MOTOR GP-ELECTRIC 3922020 - Caterpillar

3922020 STARTING MOTOR GP-ELECTRIC Caterpillar parts C7.1

Price: query
Add in request price Go to cart

Rating:

Alternative (cross code) number:
CA3922020
392-2020
3922020

Caterpillar 3922020 STARTING MOTOR GP-ELECTRIC

Buy STARTING MOTOR GP-ELECTRIC 3922020 Caterpillar genuine, new aftermarket tractor parts with delivery
INDUSTRIAL ENGINE,

Compare Prices: .

As an associate, we earn commssions on qualifying purchases through the links below

STG92728 Starter Compatible For CATERPILLAR CP-56B VIBRATORY COMPACTOR P56 461-2993 269-7369 269-7368 392-2020 435-7379

$695.37

04 Oct 2025

CN: ZHONGHAOSHANGMA

STG92728 Starter Compatible For CATERPILLAR CP-56B VIBRATORY COMPACTOR P56 461-2993 269-7369 269-7368 392-2020 435-7379
BNWFKEVM Starting Scenario: Responds to ignition commands with great speed. Even in the morning rush, you can start the engine immediately, and say goodbye to the anxiety of starting the engine repeatedly || Multi-level speed control function: supports frequency conversion speed control or step speed control to meet the speed control requirements under different working conditions and optimize the operating efficiency of the equipment || Safety protection function: built-in overload protection and overheating protection, preventing damage to the motor and prolonging its service life || Wide range of adaptability: compatible with many models, easy to replace the original parts without pressure || STG92728 Starter Compatible For CATERPILLAR CP-56B VIBRATORY COMPACTOR P56 461-2993 269-7369 269-7368 392-2020 435-7379

Number on catalog scheme:

Caterpillar 3922020 Parts scheme STARTING MOTOR GP-ELECTRIC

For full view, you need register

Compatible equipment models: 3922020:

INDUSTRIAL ENGINE C7.1 Caterpillar

Information:

Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 1
B 2P-8312 External Retaining Ring Pliers 1
C 5P-7373 Axle Installer 1 Start By:
Install the wheel chocks. Refer to Disassembly and Assembly, "Wheel Chock (Front and Rear) - Remove and Install" for the Machine System.
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting, and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, PERJ1017, "Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Cat® products.Dispose of all fluids according to local regulations and mandates.
Drain the oil from the axle housing assembly into a suitable container. The capacity of the axle housing assembly is 222 L (59 US gal). Refer to the Operation and Maintenance Manual, "Differential and Final Drive Oil - Change" for the correct procedure.
Drain the oil from the final drives into a suitable container. The capacity of one final drive is 42 L (11 US gal). Refer to the Operation and Maintenance Manual, "Differential and Final Drive Oil - Change" for the correct procedure. Note: It is not necessary to remove the rear tire and rim in order to remove the axle shaft.
Illustration 1 g00703103
Attach Tool (A) to cover (1). Position a suitable lifting device on Tool (A). Secure the suitable lifting device to a hoist.
Remove nine full nuts (2), the hard washers and cover (1) from the planetary carrier.
Illustration 2 g00699823
Use two 1/2 inch - 13 NC forcing screws (3) to remove cover (1) from the planetary carrier. Remove O-ring seal (4) from cover (1). The weight of cover (1) is 39 kg (85 lb).
Illustration 3 g00713373
Use Tool (B) (not shown) in order to remove retaining ring (6). Remove sun gear (5) and the thrust washer from axle shaft (7). Use Tool (C) (not shown) to remove axle shaft (7) from the wheel assembly.