STATOR AS 4571359 - Caterpillar

Route Radio Harness As. (6) along Instrument Panel Harness As. (M) and upward towards the top of the Cab. Note: Before strapping Radio Harness As. (6), make sure that there is enough slack to connect the Microphone. If necessary, coil and strap any excess cable from the Harness after connecting the Microphone
Begin strapping Radio Harness As. (6) to Instrument Panel Harness As. (M) by using five Cable Straps (1). Refer to Illustration 11.
Illustration 12 g03402477
(M) Instrument Panel Harness As
(1) 3S-2093 Cable Strap
(6) 353-1634 Radio Harness As
Continue attaching Radio Harness As. (6) to Instrument Panel Harness As. (M) using three Cable Straps (1). Refer to Illustration 12.
Illustration 13 g03402476
(M) Instrument Panel Harness As
(1) 3S-2093 Cable Strap
(6) 353-1634 Radio Harness As
Continue attaching Radio Harness As. (6) to Instrument Panel Harness As. (M) using three Cable Straps (1) at the locations shown in Illustration 13.
Replace the Headliner, the Left-Hand Side Cover, the Plugs, and the Right-Hand Console back to original locations. Use the provided six Fasteners (3) if necessary. Connecting the Microphone
Illustration 14 g03402480
(5) 349-8642 Microphone
(6) 353-1634 Radio Harness As
Illustration 15 g03402481
(5) 349-8642 Microphone
Connect Microphone (5) to the end Connector on Radio Harness As. (6). Insert Microphone (5) onto the Console on the open slot right below the Control Knob As. until Microphone (5) snaps into place. Refer to Illustrations 14 and 15.
Use some of the provided Seal (2) on the rear of the Radio Gp. (7) to protect the wires and connections. Connecting the Radio to the Cab Harness
Illustration 16 g03412782
(N) Hole
(P) 9U-8746 Coaxial Cable As (previously installed)
(R) 8E-1118 Antenna As
Connect the End Connector from 9U-8746 Coaxial Cable As (P) to the appropriate slot on the rear of the Radio Console (7). Hand tighten the other end of 9U-8746 Coaxial Cable As (P) to 8E-1118 Antenna As (R) that was previously installed, as indicated in Special Instruction, REHS8710. Make sure that 9U-8746 Coaxial Cable As (P) passes through Hole (N) located on the Canopy Plate and right next to the Bracket. This action will protect the Cable from movement of the arms.
Connect the Receptacle from the 200-5728 Radio Harness As (Connection AC-2) onto the appropriate slot on the rear of the Radio Console. Connect the other end of 200-5728 Radio Harness As that contains 3E-3388 Connector Receptacle As (Connection AC-1) to 155-2264 Connector Plug As (Connection C-C10). Ensure that the connection corresponds to the one shown in Table 1.
Table 2
CONNECTING AC-1 TO C-C10
AC-1 C-C10
POSITION WIRE COLOR AND GAUGE WIRE NUMBER WIRE COLOR AND GAUGE
1 WHITE/BLACK -18 509-C70 WHITE -18
2 WHITE-18 508-C68 PURPLE -18
3 BLACK-18 200-C75 BLACK -18
4 N/A N/A N/A
5 YELLOW-18 122-C74 RED -18
6 RED-18 191-C76 WHITE -16
7 GRAY/BLACK - 18 512-C72 GREEN - 18
8 GRAY - 18 511-C71 BROWN - 18