AVSPARE.COM
parts catalog

STEM 2H9264 - Caterpillar



2H9264 STEM Caterpillar parts 12E, 191, 41, 44 STEM
Rating:
27
Alternative (cross code) number:
CA2H9264
2H-9264
2H9264
Caterpillar 2H9264 STEM
Weight: 0.30 pounds 0 kg.

Buy STEM 2H9264 Caterpillar genuine, new aftermarket tractor parts with delivery
HYDRAULIC CONTROL, MOTOR GRADER,

Compatible equipment models: 2H9264:

HYDRAULIC CONTROL  191   41   44  
MOTOR GRADER  12E   Caterpillar
Number on catalog scheme: None
 
  For full view, you need register

Information:

1. Fasten a hoist to idler (1) as shown.2. Remove bolts (3) and caps (2).3. Remove shims (4). Move blocks (5) toward the roller frame, and remove idler (1) from the machine. The weight of the idler is 73 kg (160 lb).4. Remove blocks (5) from the front roller frame. The following steps are for installation of the idler.5. Put blocks (5) in position on the dowels in the front roller frame.6. Fasten a hoist, and put idler (1) in position in the blocks.7. Install shims (4) between the front roller frame and blocks.8. Align hole (6) in the idler shaft with the pin in caps (2). Install caps (2) and bolts (3). Tighten the bolts to a torque of 270 25 N m (200 18 lb ft).End By:a. connection of tracksDisassemble Idlers
Start By:a. remove idlers 1. Use a slow speed drill and a 12.7 mm (.50 in) drill bit, and remove plug (4) and stopper (3) from the end of the shaft.
The shaft will be free to fall when the retainers are removed.
2. Remove 12 bolts (2) and retainer (1) from both sides of the idler. 3. Remove O-ring seal (6) from retainer (1). If the Duo-Cone seals are to be used again, put identification marks on the seals so they can be assembled and installed in their original position.4. Put identification marks on the Duo-Cone seal. Remove Duo-Cone seal (5) from retainer (1). 5. Put identification marks on Duo-Cone seal (7). Remove Duo-Cone seal (7) and toric stabilizer (8) from shaft (9). 6. Remove shaft (9) from idler assembly (10).Assemble Idlers
1. Clean and inspect all parts for wear or damage. Replace all parts that are worn or damaged.2. Make sure all parts are free of oil film, dust or other foreign material. Use Trichlorethane and a clean cloth or paper towel for cleaning.
The bearing in idler assembly (1) can be damaged when shaft (2) is installed in the idler.
3. Carefully put shaft (2) in position in idler assembly (1). 4. Put toric stabilizers (3) in position on both ends of shaft (2). See Installation Of Duo-Cone Floating Seals before installation of any of the Duo-Cone seals.5. Put toric ring (4) in position in seal ring (5). Make sure the toric ring is straight in seal ring (5).6. Put ring (4) and seal ring (5) in Trichlorethane until the entire toric ring is wet. 7. Use tool (A) to install the toric ring and seal ring (5) on shaft (2). Install the rings until tool (A) makes contact with the end of shaft (2). 8. Use a depth micrometer (6) to measure the distance between seal ring (5) and the shaft at four locations 90° apart. The difference in these measurements must not be more than 0.80 mm (.031 in).9. If adjustments to seal ring (5) are necessary, use tool (A) to adjust the seal ring on the shaft.10. Repeat Steps 5 through 9 to install the toric ring and seal ring on the

Caterpillar parts catalog:

Caterpillar parts catalog
NO. 12 MOTOR GRADER 99E00001-04490 (MACHINE)
NO. 12 MTR. GRADER 99E04491-14170 (MACHINE)
NO. 41 HYDRAULIC CONTROL 28C00001-00424
NO. 41 HYD. CONTROL FRONT MOUNTED 24C00001-UP
NO. 41 HYDRAULIC CONTROL 28C00001-00424
NO. 41 HYD. CONTROL FRONT MOUNTED 24C00001-UP
NO. 41 HYDRAULIC CONTROL 28C00001-00424
NO. 41 HYD. CONTROL FRONT MOUNTED 24C00001-UP
NO. 41 HYDRAULIC CONTROL 28C00001-00424
NO. 41 HYD. CONTROL FRONT MOUNTED 24C00001-UP
NO. 44 HYDRAULIC CONTROL 06W05001-UP
NO. 44 HYDRAULIC CONTROL 07W00001-UP
NO. 44 HYDRAULIC CONTROL 09W00001-UP
141, 143, 161, 181 & 191 HYD. CONTROLS 36F00001-00413
NO. 44 HYDRAULIC CONTROL 09W00001-UP
141, 143, 161, 181 & 191 HYD. CONTROLS 36F00001-00413


Parts stem Caterpillar catalog:

6V4652 STEM ASSEM. (straight)
772B, 916, 926, 926A, AD55, D10, D6D, D6H, D7H, D8L
6V4669 STEM ASSEM. (60 degrees)
D6D, D6H, D6H XR, D6R, D6R III, D7H
6V4677 STEM AS-COLLET
769C, 772B, 776, 963, 973, AD30, AD40, AD45, AD55, AE40, AE40 II, R1300, R2900, R2900G
5H3546 STEM
191, 955C, 955H
5H6118 STEM
50, 583H, 955C, 977D, 977H
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.