3446921 STEP AS Caterpillar parts
312E, 312E L
Rating:
Alternative (cross code) number:
CA3446921
344-6921
3446921
CA3446921
344-6921
3446921
Weight: 11 pounds 5 kg.
EXCAVATOR,
Number on catalog scheme:
1
For full view, you need register
Information:
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-6683 Ring Expander 1
B 1P-1857 Retaining Ring Pliers 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00893862
Ream piston pin bushing (7) in order to obtain a clearance of 0.0085 0.0055 mm (0.00030 0.00020 inch) between the piston pin and the piston pin bushing.
Lubricate all components with clean engine oil.
Use a suitable press and a suitable adapter to install piston pin bushing (7) into connecting rod (6). Note: Ensure that the oil hole in the piston pin bushing is aligned with the oil hole at the top of the connecting rod.
Illustration 2 g00551460
Typical example
Install bearing (5) in connecting rod (6).
Install piston pin (4) into the piston and through connecting rod (6). Note: If the piston pin cannot be installed by hand, heat the piston to a temperature of 45° 5°C (113° 9°F).
Use Tooling (B) in order to install retaining rings (3) that hold the piston pin in position.
Illustration 3 g00551459
Use Tooling (A) in order to install piston rings (1) on piston (2) with the following steps.
Install the oil control piston ring in the groove that is lowest on the piston. The latch pin that is on the oil control ring must be inside the ends of the spring. Note: Ensure that the latch pin that is on the oil control ring is 180 degrees from the oil control ring gap.
Install the intermediate piston ring with the tapered face into the second groove on the piston. The stamp "TOP" must be toward the top of the piston. Note: Intermediate piston rings that are new have a green mark which must be on the left of the piston ring gap when the piston ring is installed.
Position the piston ring gaps at 120 degrees away from each other.
Install the top piston ring with the barrel face and the molybdenum insert into the top groove on the piston. The top piston ring has a wedge shape. The stamp "TOP" must be toward the top of the piston. Note: Top piston rings that are new have a red mark which must be on the left of the ring gap when the ring is installed.End By:
Install the pistons and the connecting rods. Refer to Disassembly and Assembly, "Piston and Connecting Rods - Install".
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-6683 Ring Expander 1
B 1P-1857 Retaining Ring Pliers 1
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00893862
Ream piston pin bushing (7) in order to obtain a clearance of 0.0085 0.0055 mm (0.00030 0.00020 inch) between the piston pin and the piston pin bushing.
Lubricate all components with clean engine oil.
Use a suitable press and a suitable adapter to install piston pin bushing (7) into connecting rod (6). Note: Ensure that the oil hole in the piston pin bushing is aligned with the oil hole at the top of the connecting rod.
Illustration 2 g00551460
Typical example
Install bearing (5) in connecting rod (6).
Install piston pin (4) into the piston and through connecting rod (6). Note: If the piston pin cannot be installed by hand, heat the piston to a temperature of 45° 5°C (113° 9°F).
Use Tooling (B) in order to install retaining rings (3) that hold the piston pin in position.
Illustration 3 g00551459
Use Tooling (A) in order to install piston rings (1) on piston (2) with the following steps.
Install the oil control piston ring in the groove that is lowest on the piston. The latch pin that is on the oil control ring must be inside the ends of the spring. Note: Ensure that the latch pin that is on the oil control ring is 180 degrees from the oil control ring gap.
Install the intermediate piston ring with the tapered face into the second groove on the piston. The stamp "TOP" must be toward the top of the piston. Note: Intermediate piston rings that are new have a green mark which must be on the left of the piston ring gap when the piston ring is installed.
Position the piston ring gaps at 120 degrees away from each other.
Install the top piston ring with the barrel face and the molybdenum insert into the top groove on the piston. The top piston ring has a wedge shape. The stamp "TOP" must be toward the top of the piston. Note: Top piston rings that are new have a red mark which must be on the left of the ring gap when the ring is installed.End By:
Install the pistons and the connecting rods. Refer to Disassembly and Assembly, "Piston and Connecting Rods - Install".
Caterpillar parts catalog:
Parts step Caterpillar catalog:
3595799
STEP
312E, 312E L, 320D, 320D L, 320D LRR, 320D RR, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 329E
312E, 312E L, 320D, 320D L, 320D LRR, 320D RR, 320E, 320E L, 320E LN, 320E LRR, 320E RR, 323E L, 329E
3480635
STEP AS
312E, 312E L, 316E L, 318E L, 320E, 320E L, 320E LN, 323E L, 324E, 324E L, 324E LN, 329E, 329E L, 329E LN, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 349E, 349E L, 349E L HVG, 349E L VG
312E, 312E L, 316E L, 318E L, 320E, 320E L, 320E LN, 323E L, 324E, 324E L, 324E LN, 329E, 329E L, 329E LN, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 349E, 349E L, 349E L HVG, 349E L VG
3490058
STEP AS
312E, 312E L, 316E L, 318E L, 320E LN, 323E L
312E, 312E L, 316E L, 318E L, 320E LN, 323E L
3921576
STEP AS
M318D MH
M318D MH
2866026
STEP AS
314D CR, 314D LCR
314D CR, 314D LCR
3150885
STEP AS
312D
312D
3872699
STEP AS
M318D
M318D
4220596
STEP
313D2 LGP
313D2 LGP
3719719
STEP AS
314E CR, 314E LCR
314E CR, 314E LCR
3719718
STEP AS
314E CR, 314E LCR
314E CR, 314E LCR
3849076
STEP AS
312D2, 312D2 GC, 312D2 L, 313D, 313D2, 313D2 LGP, 318D L, 318D2 L
312D2, 312D2 GC, 312D2 L, 313D, 313D2, 313D2 LGP, 318D L, 318D2 L
3902392
STEP AS
M313D, M315D
M313D, M315D