parts catalog

STICK AR-HOE 3905091 - Caterpillar

3905091 STICK AR-HOE Caterpillar parts M313D STICK
Alternative (cross code) number:
Caterpillar 3905091 STICK AR-HOE

Buy STICK AR-HOE 3905091 Caterpillar genuine, new aftermarket tractor parts with delivery

You can buy parts: .


15 Nov 2020
1.0[0.45] Pounds
D&D PowerDrive 3905091 GMC General Motors Corp Replacement Belt, Rubber
Belt 17.53 x 58.27in OC || Material type- rubber || Manufactured by D&D PowerDrive
  For full view, you need register

Compatible equipment models: 3905091:

WHEELED EXCAVATOR  M313D   Caterpillar


Storage (Less Than One Year)
If an engine is not used, oil can run off the following parts that normally receive lubrication: cylinder walls, piston rings, main bearings, connecting rod bearings, crankshaft and gears.This lack of lubricant allows corrosion to begin to appear on the metal. This condition is worse in areas of high humidity.When the engine is started again, metal to metal contact will cause wear before the surfaces receive oil. To minimize this wear, use the starter to turn the engine with the throttle in the FUEL OFF position. When oil pressure is shown on the pressure gauge, start the engine.
Clean the engine of any dirt, rust, grease, and oil. Inspect the exterior. Paint areas that contain paint damage with a good quality paint.
Remove dirt from the air cleaners. Check all seals, gaskets, and the filter element for damage.
Apply lubricant to all points in this Operation and Maintenance Manual, "Maintenance Interval Schedule".
Drain the crankcase oil. Replace the crankcase oil and change the oil filters. For the proper procedure, refer to this Operation and Maintenance Manual.
If the engine is equipped with an air starting motor, fill the reservoir with the following mixture: 50 percent volatile corrosion inhibitor oil (<nomen>VCI oil</nomen>) and 50 percent engine oil.
Add VCI oil to the crankcase oil. The volume of VCI oil in the crankcase oil should be 3 to 4 percent. Note: If the engine crankcase is full, drain enough engine oil so the mixture can be added.
Remove the air filter elements. Turn the engine at cranking speed with the throttle control in FUEL OFF position. Use a sprayer to add a mixture of 50 percent VCI oil and 50 percent engine oil into the air inlet or turbocharger inlet. Note: The mixture of VCI oil can be added to the inlet by removing the plug for checking turbocharger boost pressure. The minimum application rate for the VCI oil mixture is 5.5 mL per L (3 oz per 1000 cu in) of engine displacement.
Use a sprayer to apply a mixture of 50 percent VCI oil and 50 percent crankcase oil into the exhaust openings. The minimum application rate for the oil mixture is 5.5 mL per L (3 oz per 1000 cu in) of engine displacement. Seal the exhaust pipe and seal any drain holes in the muffler.
Remove the fuel from the secondary fuel filter housing. Alternately, empty and reinstall the spin-on fuel filter element in order to remove any dirt and water. Drain any sleeve metering fuel pump. Clean the primary fuel filter. Fill with calibration fluid or kerosene. Install the primary fuel filter and operate the priming pump. This procedure will send clean oil to the secondary filter and the engine.Open the fuel tank drain valve in order to drain any water and dirt from

Caterpillar SIS machinery equipment:

Caterpillar SIS

Caterpillar parts catalog:

Caterpillar parts catalog
M313D Excavator K3D00001-UP (MACHINE) POWERED BY C4.4 Engine

Parts stick Caterpillar catalog:

2730835 STICK GP-HOE
M313D, M315D 2, M317D 2
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.