5I8767 STOP Caterpillar parts
308E, 308E CR, 308E SR, 311, 311B, 312, 312B, 312B L, 315, 315B, 315B FM L, 315B L, 317, 317B LN, 318B
Rating:
Alternative (cross code) number:
CA5I8767
5I-8767
5I8767
CA5I8767
5I-8767
5I8767
Weight: 0.17 pounds 0 kg.
EXCAVATOR, MINI HYD EXCAVATOR,
Compatible equipment models: 5I8767:
Number on catalog scheme:
12
For full view, you need register
Caterpillar parts catalog:
Information:
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench As 1
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Illustration 1 g01250304
Remove bolts (1). Remove sheet (2) .
Illustration 2 g01250305
Turn valve (3) to the OFF position.
Illustration 3 g01250522
Open door (4) .
Illustration 4 g01250523
Drain the water separator (8) into a container for storage or disposal. Disconnect hose (9). Disconnect harness assembly (10) .
Use Tooling (A) in order to remove water separator (8). Remove water separator (8) .
Disconnect hose assemblies (6) .
Remove bolts (5). Remove water separator base (7) .Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
Illustration 5 g01250523
Position water separator base (7). Install bolts (5) .
Connect hose assemblies (6) .
Install water separator (8).
Connect harness assembly (10). Connect hose (9) .
Purge the air from the fuel system.
Illustration 6 g01250522
Close door (4) .
Illustration 7 g01250305
Turn valve (3) to the ON position.
Illustration 8 g01250304
Position sheet (2). Install bolts (1) .
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench As 1
Care must be taken to ensure that fluids are contained during performance of inspection, maintenance, testing, adjusting and repair of the product. Be prepared to collect the fluid with suitable containers before opening any compartment or disassembling any component containing fluids.Refer to Special Publication, NENG2500, "Caterpillar Dealer Service Tool Catalog" for tools and supplies suitable to collect and contain fluids on Caterpillar products.Dispose of all fluids according to local regulations and mandates.
Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism.Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system.
Illustration 1 g01250304
Remove bolts (1). Remove sheet (2) .
Illustration 2 g01250305
Turn valve (3) to the OFF position.
Illustration 3 g01250522
Open door (4) .
Illustration 4 g01250523
Drain the water separator (8) into a container for storage or disposal. Disconnect hose (9). Disconnect harness assembly (10) .
Use Tooling (A) in order to remove water separator (8). Remove water separator (8) .
Disconnect hose assemblies (6) .
Remove bolts (5). Remove water separator base (7) .Installation Procedure
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are worn or damaged, use new parts for replacement.
Illustration 5 g01250523
Position water separator base (7). Install bolts (5) .
Connect hose assemblies (6) .
Install water separator (8).
Connect harness assembly (10). Connect hose (9) .
Purge the air from the fuel system.
Illustration 6 g01250522
Close door (4) .
Illustration 7 g01250305
Turn valve (3) to the ON position.
Illustration 8 g01250304
Position sheet (2). Install bolts (1) .
Parts stop Caterpillar catalog:
1290T, 2290, 2390, 2391, 311, 311B, 311C, 312, 312B, 312B L, 312C, 315, 315B, 315B L, 315C, 315D L, 317, 317B LN, 318B, 318C, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320B FM LL, 320B L, 320C, 320C F...
1961507
STOP
308C, 308D, 308E CR, 308E SR, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 321C, 321D LCR, 325C, 328D LCR
308C, 308D, 308E CR, 308E SR, 314C, 314D CR, 314D LCR, 314E CR, 314E LCR, 321C, 321D LCR, 325C, 328D LCR
1069595
STOP
318B, 318C, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320E LN, 321D LCR, 323D L, 323D LN, 323D SA, 323E L, 325B L, 325C, 325D L, 330B L, 330C, 330D L, 345B L
318B, 318C, 319C, 319D, 319D L, 319D LN, 320 L, 320B, 320C, 320E LN, 321D LCR, 323D L, 323D LN, 323D SA, 323E L, 325B L, 325C, 325D L, 330B L, 330C, 330D L, 345B L
2743526
STOP-RUBBER
305.5, 305.5E, 306, 306E, 307E, 308E, 308E2 CR
305.5, 305.5E, 306, 306E, 307E, 308E, 308E2 CR
3279650
STOP
307D, 307E, 308D, 308E, 308E CR, 308E SR, 308E2 CR
307D, 307E, 308D, 308E, 308E CR, 308E SR, 308E2 CR
2735205
STOP
308D, 308E CR, 308E SR, 314D CR, 314D LCR, 314E CR, 314E LCR, 321D LCR, 328D LCR
308D, 308E CR, 308E SR, 314D CR, 314D LCR, 314E CR, 314E LCR, 321D LCR, 328D LCR
3531940
STOP
308D, 308E CR, 308E SR, 314D CR, 314D LCR, 314E CR, 314E LCR, 321D LCR
308D, 308E CR, 308E SR, 314D CR, 314D LCR, 314E CR, 314E LCR, 321D LCR
3168933
STOP
308D, 308E CR, 308E SR, 312D, 312D L, 312E, 312E L, 314D CR, 314D LCR, 314E CR, 314E LCR, 315D L, 316E L, 318E L, 319D L, 319D LN, 320D, 320D L, 320D LRR, 320D RR, 320E, 320E L, 320E LN, 320E LRR, 320...
308D, 308E CR, 308E SR, 312D, 312D L, 312E, 312E L, 314D CR, 314D LCR, 314E CR, 314E LCR, 315D L, 316E L, 318E L, 319D L, 319D LN, 320D, 320D L, 320D LRR, 320D RR, 320E, 320E L, 320E LN, 320E LRR, 320...
3168932
STOP
308E, 308E2 CR, 311D LRR, 311F LRR, 324D L, 324E, 324E L, 324E LN, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 336D, 336D L, 336D LN, 336D2, 336E, 336E H, 336E L, 336E LH, 336E LN, 336F L,...
308E, 308E2 CR, 311D LRR, 311F LRR, 324D L, 324E, 324E L, 324E LN, 328D LCR, 329D, 329D L, 329D LN, 329E, 329E L, 329E LN, 336D, 336D L, 336D LN, 336D2, 336E, 336E H, 336E L, 336E LH, 336E LN, 336F L,...
3825763
STOP
308E, 308E CR, 308E2 CR
308E, 308E CR, 308E2 CR
3825790
STOP
308E, 308E CR, 308E2 CR
308E, 308E CR, 308E2 CR
3898724
STOP
307E, 308E, 308E2 CR
307E, 308E, 308E2 CR
311, 311B, 312, 312B, 312B L, 313B, 315, 315B, 315B FM L, 315B L, 317, 317B LN, 318B
6I6033
STOP
307, 308C, 308D, 311, 311B, 311C, 311D LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 313D, 313D2, 313D2 LGP, 315, 315B, 315B L, 315C, 317, 317B LN, 318B, 318C, 319C, 32...
307, 308C, 308D, 311, 311B, 311C, 311D LRR, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 312D2, 312D2 GC, 312D2 L, 313D, 313D2, 313D2 LGP, 315, 315B, 315B L, 315C, 317, 317B LN, 318B, 318C, 319C, 32...
312, 312B, 312C, 312C L, 313B
5I3046
STOP
311, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 313B, 313D2, 314C, 345B II, 345C, M315C, M315D, M316C, M316D, M317D 2
311, 312, 312B, 312B L, 312C, 312C L, 312D, 312D L, 313B, 313D2, 314C, 345B II, 345C, M315C, M315D, M316C, M316D, M317D 2
7I7513
STOP
307, 307B, 307C, 312, 312B, 312B L, 312C L, 313B
307, 307B, 307C, 312, 312B, 312B L, 312C L, 313B
8U4051
STOP
213B, 214B, 224B, 312, 312B L, 315, 317
213B, 214B, 224B, 312, 312B L, 315, 317
4I5664
STOP
311, 312, 315, 317, 320 L, 325, 325 L, 330
311, 312, 315, 317, 320 L, 325, 325 L, 330
1020913
STOP
307, 311, 312, 313B, 314C, 315, 317, 320 L, 321B, 321C, 325, 325 L, 325D MH, 330, 330D, 330D L, 330D MH, 345C, 345C MH, M325D L MH, M325D MH, M330D
307, 311, 312, 313B, 314C, 315, 317, 320 L, 321B, 321C, 325, 325 L, 325D MH, 330, 330D, 330D L, 330D MH, 345C, 345C MH, M325D L MH, M325D MH, M330D
7I7214
STOP
311, 311B, 312, 312B, 312B L, 313B, 315, 315B, 315B L, 317, 317B LN, 318B, 375
311, 311B, 312, 312B, 312B L, 313B, 315, 315B, 315B L, 317, 317B LN, 318B, 375
7I7202
STOP
311, 312, 315, 317, 375
311, 312, 315, 317, 375
5I8765
STOP
311, 311B, 312, 312B, 312B L, 315, 315B, 315B FM L, 315B L, 317, 317B LN, 318B, 365B II, 365C, 365C L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5090B
311, 311B, 312, 312B, 312B L, 315, 315B, 315B FM L, 315B L, 317, 317B LN, 318B, 365B II, 365C, 365C L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5090B
5I8768
STOP
308E, 308E CR, 308E SR, 311, 311B, 312, 312B, 312B L, 315, 315B, 315B FM L, 315B L, 317, 317B LN, 318B
308E, 308E CR, 308E SR, 311, 311B, 312, 312B, 312B L, 315, 315B, 315B FM L, 315B L, 317, 317B LN, 318B