7G2421 STOP Caterpillar parts
589, D10N, D10R, D10T, D10T2, D9L
Rating:
Alternative (cross code) number:
CA7G2421
7G-2421
7G2421
CA7G2421
7G-2421
7G2421
Weight: 3 pounds 1 kg.
PIPELAYER, TRACK-TYPE TRACTOR,
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
CTP 7G2421 General Stop for Heavy Equipment
CTP General Stop Only || Sold in each || Easy in-and-out fit
CTP General Stop Only || Sold in each || Easy in-and-out fit
CTP 7G2421 General Stop for Heavy Equipment
CTP General Stop Only || Sold in each || Easy in-and-out fit
CTP General Stop Only || Sold in each || Easy in-and-out fit
Compatible equipment models: 7G2421:
Information:
Installation Procedure
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     439-3939     Link Bracket     2    
B     8T-5096     Dial Indicator Group     1    
C     4C-5590     Anti-Seize Compound     -    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the crankshaft main bearing tabs engage with the grooves in the block and the crankshaft main bearing cap.
Place the upper halves of the crankshaft main bearings in the cylinder block. Place the lower halves of the crankshaft main bearings in crankshaft main bearing caps.
Illustration 1 g01013519
Attach Tooling (A) and a suitable lifting device to crankshaft (6) . The weight of crankshaft (6) is approximately 129 kg (285 lb). Position the upper half of the crankshaft main bearings and crankshaft (6) in the cylinder block.
Install crankshaft thrust bearings (3) .
Install the lower half of crankshaft main bearings (5) .Note: Crankshaft main bearing caps (4) should be installed with the part number toward the right side of the engine. The numerical sequence is identified by stamped numbers 1 through 7 that are located on the bottom surface. The thrust plate is used on the number 4 crankshaft main bearing only.
Position crankshaft main bearing caps (4) with the part numbers toward the right-hand side of the cylinder block. Position crankshaft main bearing caps (4) in a numerical sequence.Note: Inspect the bolts for main bearing caps (4) . Refer to Reuse and Salvage Guidelines, SEBF8301, "Inspection and Reuse of Critical Fasteners Used in All Engines" to determine if the bolts should be replaced or reused.
Apply clean "SAE 30W" oil or molybdenum grease to the bolt threads and the washers. Install the bolts. Tighten the bolts to a torque of 150 5 N m (110 5 lb ft). Place an index mark on each bolt head. Turn the bolts for an additional 60 5 degrees (1/6 turn).
Check the end play of the crankshaft with Tooling (B) . The end play must be 0.10 to 0.50 mm (0.004 to 0.020 inch).Note: Careful handling is required for fractured connecting rods. Fractured faces for the connecting rod and connecting rod cap should not be placed on any surface. The connecting rod and the connecting rod cap should be placed on the sides in order to prevent damage. When possible, the connecting rod and the connecting rod cap should be bolted together in order to prevent damage.
Install connecting rod bearings (1) and connecting rod caps (2) .
Apply Tooling (C) to the connecting rod cap bolts. Install the connecting rod cap bolts. Tighten the connecting rod cap bolts to a torque of 130 7 N m (95 5 lb ft).
Place an index mark on each bolt head. Tighten each bolt for an additional 60 5 degrees (1/6 turn).End By:
Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install".
Install the front housing. Refer to Disassembly
Table 1
Required Tools    
Tool     Part Number     Part Description     Qty    
A     439-3939     Link Bracket     2    
B     8T-5096     Dial Indicator Group     1    
C     4C-5590     Anti-Seize Compound     -    
Keep all parts clean from contaminants.Contaminants may cause rapid wear and shortened component life.
Ensure that the crankshaft main bearing tabs engage with the grooves in the block and the crankshaft main bearing cap.
Place the upper halves of the crankshaft main bearings in the cylinder block. Place the lower halves of the crankshaft main bearings in crankshaft main bearing caps.
Illustration 1 g01013519
Attach Tooling (A) and a suitable lifting device to crankshaft (6) . The weight of crankshaft (6) is approximately 129 kg (285 lb). Position the upper half of the crankshaft main bearings and crankshaft (6) in the cylinder block.
Install crankshaft thrust bearings (3) .
Install the lower half of crankshaft main bearings (5) .Note: Crankshaft main bearing caps (4) should be installed with the part number toward the right side of the engine. The numerical sequence is identified by stamped numbers 1 through 7 that are located on the bottom surface. The thrust plate is used on the number 4 crankshaft main bearing only.
Position crankshaft main bearing caps (4) with the part numbers toward the right-hand side of the cylinder block. Position crankshaft main bearing caps (4) in a numerical sequence.Note: Inspect the bolts for main bearing caps (4) . Refer to Reuse and Salvage Guidelines, SEBF8301, "Inspection and Reuse of Critical Fasteners Used in All Engines" to determine if the bolts should be replaced or reused.
Apply clean "SAE 30W" oil or molybdenum grease to the bolt threads and the washers. Install the bolts. Tighten the bolts to a torque of 150 5 N m (110 5 lb ft). Place an index mark on each bolt head. Turn the bolts for an additional 60 5 degrees (1/6 turn).
Check the end play of the crankshaft with Tooling (B) . The end play must be 0.10 to 0.50 mm (0.004 to 0.020 inch).Note: Careful handling is required for fractured connecting rods. Fractured faces for the connecting rod and connecting rod cap should not be placed on any surface. The connecting rod and the connecting rod cap should be placed on the sides in order to prevent damage. When possible, the connecting rod and the connecting rod cap should be bolted together in order to prevent damage.
Install connecting rod bearings (1) and connecting rod caps (2) .
Apply Tooling (C) to the connecting rod cap bolts. Install the connecting rod cap bolts. Tighten the connecting rod cap bolts to a torque of 130 7 N m (95 5 lb ft).
Place an index mark on each bolt head. Tighten each bolt for an additional 60 5 degrees (1/6 turn).End By:
Install the flywheel housing. Refer to Disassembly and Assembly, "Flywheel Housing - Remove and Install".
Install the front housing. Refer to Disassembly
Caterpillar parts catalog:
Parts stop Caterpillar catalog:
8P0399
STOP
528, 578, 583R, 589
528, 578, 583R, 589
3T2318
STOP
578, 583R, 589
578, 583R, 589
9U9317
STOP-BRAKE
578, 583R, 589
578, 583R, 589
9W1544
STOP
517, 527, D10N, D11N, D4H, D4H XL, D4HTSK II, D4HTSK III, D5H, D5H XL, D5HTSK II, D5M, D6H, D6H XL, D6M, D7H, D9L, D9N, D9R
517, 527, D10N, D11N, D4H, D4H XL, D4HTSK II, D4HTSK III, D5H, D5H XL, D5HTSK II, D5M, D6H, D6H XL, D6M, D7H, D9L, D9N, D9R
2P3683
STOP
55, D10N, D10R, D5B, D6D, D7G, D9N
55, D10N, D10R, D5B, D6D, D7G, D9N
8P0325
STOP ASSEM.
D10N, D10R, D6D, D7G
D10N, D10R, D6D, D7G
6Y0729
STOP
24H, 814F, 815F, 816F, 824G, 825G, 826G, 844, 844H, 844K, 854G, 854K, 936F, 950F, 950F II, 960F, 966F II, 970F, 980F, 980F II, 980G, 980G II, 988F, 988F II, 990, 990 II, 990H, 990K, 992D, 992G, 992K, ...
24H, 814F, 815F, 816F, 824G, 825G, 826G, 844, 844H, 844K, 854G, 854K, 936F, 950F, 950F II, 960F, 966F II, 970F, 980F, 980F II, 980G, 980G II, 988F, 988F II, 990, 990 II, 990H, 990K, 992D, 992G, 992K, ...
6Y0727
STOP
24H, 814F, 815F, 816F, 824G, 825G, 826G, 844, 844H, 844K, 854G, 854K, 936F, 950F, 950F II, 960F, 966F, 966F II, 970F, 980F, 980F II, 980G, 980G II, 988F, 988F II, 990, 990 II, 990H, 990K, 992D, 992G, ...
24H, 814F, 815F, 816F, 824G, 825G, 826G, 844, 844H, 844K, 854G, 854K, 936F, 950F, 950F II, 960F, 966F, 966F II, 970F, 980F, 980F II, 980G, 980G II, 988F, 988F II, 990, 990 II, 990H, 990K, 992D, 992G, ...
6Y0744
STOP
24H, 814F, 815F, 816F, 824G, 825G, 826G, 844, 844H, 844K, 854G, 854K, 936F, 950F, 950F II, 960F, 966F, 966F II, 970F, 980F, 980F II, 980G, 980G II, 988F, 988F II, 990, 990 II, 990H, 990K, 992D, 992G, ...
24H, 814F, 815F, 816F, 824G, 825G, 826G, 844, 844H, 844K, 854G, 854K, 936F, 950F, 950F II, 960F, 966F, 966F II, 970F, 980F, 980F II, 980G, 980G II, 988F, 988F II, 990, 990 II, 990H, 990K, 992D, 992G, ...
1167474
STOP
814F, 815F, 816F, 994, 994D, 994F, 994H, D10R, D11R, D11T
814F, 815F, 816F, 994, 994D, 994F, 994H, D10R, D11R, D11T
9G1368
STOP-RUBBER
D10, D10R, D10T, D10T2, D11N, D11R, D11T
D10, D10R, D10T, D10T2, D11N, D11R, D11T
2715040
STOP
D10T, D11T, D7E, D7E LGP, D8T, D9T
D10T, D11T, D7E, D7E LGP, D8T, D9T
6P4971
STOP
517, 527, 561M, 578, 583R, 587R, 589, 814B, 815B, 826C, 834B, 836, 910, 916, 926, 931B, 933, 935C, 936, 936F, 939, 950B, 950B/950E, 950F, 950F II, 966D, 966F, 980C, 980F, 983B, 988B, 992C, 994, AD30, ...
517, 527, 561M, 578, 583R, 587R, 589, 814B, 815B, 826C, 834B, 836, 910, 916, 926, 931B, 933, 935C, 936, 936F, 939, 950B, 950B/950E, 950F, 950F II, 966D, 966F, 980C, 980F, 983B, 988B, 992C, 994, AD30, ...
6Y1199
STOP AS
527, 561H, 963, 963B, 963C, D4H, D4HTSK II, D6R, D6R II, D6R III, D6T
527, 561H, 963, 963B, 963C, D4H, D4HTSK II, D6R, D6R II, D6R III, D6T
8Y6428
STOP-RUBBER
D11N, D4H, D4H XL, D4HTSK II, D4HTSK III, D5H, D5H XL, D5HTSK II, D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6T, D6T XL, D7H, D7R, D7R II, D8N, D8R, D8R II
D11N, D4H, D4H XL, D4HTSK II, D4HTSK III, D5H, D5H XL, D5HTSK II, D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6T, D6T XL, D7H, D7R, D7R II, D8N, D8R, D8R II
1093969
STOP
561N, 572R, 572R II, 587T, 824G II, 824H, 825G II, 825H, 826G II, 826H, 834G, 834H, 836G, 836H, 980H, 980K, 980K HLG, 986H, 988G, 988H, D10R, D10T, D5M, D5N, D6M, D6N, D6R, D6R II, D7R, D7R II, D8R II...
561N, 572R, 572R II, 587T, 824G II, 824H, 825G II, 825H, 826G II, 826H, 834G, 834H, 836G, 836H, 980H, 980K, 980K HLG, 986H, 988G, 988H, D10R, D10T, D5M, D5N, D6M, D6N, D6R, D6R II, D7R, D7R II, D8R II...
8E2139
STOP AS
572R II, 589, D6R, D6R II, D6R III, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7E, D7E LGP, D7H, D7R, D7R II, D7R XR, D8L, D8R, D8R II, D8T
572R II, 589, D6R, D6R II, D6R III, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7E, D7E LGP, D7H, D7R, D7R II, D7R XR, D8L, D8R, D8R II, D8T
1038330
STOP
307
307
7M1377
STOP-VALVE
572G, 572R, 572R II, 578, 583R, 587R, 587T, 988, D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7F, D7G, D7H, D7R, D7R II, D7R XR, D8H, D8K, D8N, D8R, PL87
572G, 572R, 572R II, 578, 583R, 587R, 587T, 988, D6H, D6H XL, D6H XR, D6R, D6R II, D6R III, D6R STD, D6T, D6T LGP, D6T LGPPAT, D6T XL, D7F, D7G, D7H, D7R, D7R II, D7R XR, D8H, D8K, D8N, D8R, PL87
9U9317
STOP-BRAKE
578, 583R, 589
578, 583R, 589
3T2318
STOP
578, 583R, 589
578, 583R, 589
8P0399
STOP
528, 578, 583R, 589
528, 578, 583R, 589
9W9711
STOP
578, 589
578, 589
3T2320
STOP
578, 583R, 589
578, 583R, 589