AVSPARE.COM
parts catalog

STRIP 2444950 - Caterpillar


2444950 STRIP Caterpillar parts 994F
Rating:
56
Alternative (cross code) number:
CA2444950
244-4950
2444950
Caterpillar 2444950 STRIP
Weight: 6 pounds 3 kg.

Buy STRIP 2444950 Caterpillar genuine, new aftermarket tractor parts with delivery
WHEEL LOADER,

Compatible equipment models: 2444950:

WHEEL LOADER  994F   Caterpillar
Number on catalog scheme: 6
 
  For full view, you need register

Information:


Illustration 1 g02913863
Schematic of the Hoe Auxiliary Valve No. 1 Port B solenoid
This diagnostic code is associated with the Hoe Auxiliary Valve No. 1 Port B solenoid. The FMI 03 means that the ECM has determined that the voltage of the solenoid circuit is above normal. Possible causes of the diagnostic code are:
The energize circuit of the solenoid is shorted to another power supply circuit.
The ECM has failed, but is unlikely.Note: The following test procedure may create other diagnostic codes. Ignore these created diagnostic codes and clear these diagnostic codes when the original diagnostic code has been corrected. Ensure that the diagnostic code of CID 2237 FMI 03 is active before performing this procedure.Note: Use the 146-4080 Digital Multimeter for the measurements in this procedure.System Response:
The system will not initialize after power is cycled.
The hydraulic functions for Extend, Retract, Reverse, and Forward positions are lost after power is cycled.Test Step 1. CHECK THE SOLENOID ENERGIZE CIRCUIT FOR A SHORT.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the Hoe Auxiliary Valve No. 1 Port B solenoid from the machine harness connector.
Disconnect the J1 machine harness connector from the ECM.
On the J1 ECM connector, measure the resistance from contact J1-59 (wire T969-YL(Yellow)) to all the other contact pins used in the connector. Expected Result:The measurements are all greater than 5000 ohms.Results:
OK - There are no shorts in the wires. Proceed to Test Step 2.
NOT OK - There is a short in the machine harness or in the wires. The short is to the wire with the low resistance reading.Repair: Repair, or replace, the machine harness. Ensure that the problem has been corrected.STOPTest Step 2. CHECK THE OPERATION OF THE ECM.Reconnect the J1 machine harness connector to the ECM. The machine harness connector for the solenoid remains disconnected.
Turn the disconnect switch and the key start switch to the ON position.
Observe the status of the active diagnostic code. Expected Result:The diagnostic code of FMI 03 changes to an FMI 05 diagnostic code.Results:
OK - The FMI 03 changed to an FMI 05 diagnostic code. The FMI 05 was activated because the solenoid circuit is disconnected. The ECM has responded correctly to the condition of an open solenoid circuit. Reconnect the solenoid to the harness. Proceed to Test Step 3.
NOT OK - The FMI 03 diagnostic code did not change to an FMI 05 diagnostic code. The active diagnostic code did not change after the solenoid was disconnected from the ECM.Repair: The ECM has not responded correctly to the condition of an open solenoid circuit. The ECM might have failed. Prior to replacing an ECM, contact your Dealership Technical Communicator for possible consultation with Caterpillar. If the ECM needs to be replaced, see Testing and Adjusting, "Electronic Control Module (ECM) - Replace".STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE IS STILL ACTIVE.
Inspect the harness connectors. Clean the contacts of the harness connectors. Check the wires for damage to the insulation that can be caused by excessive heat, battery acid,

Caterpillar parts catalog:

Caterpillar parts catalog
994F Wheel Loader 44200001-UP (MACHINE) POWERED BY 3516 Engine


Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.