AVSPARE.COM
parts catalog

STUD 0001829 - Caterpillar



0001829 STUD Caterpillar parts STUD
Rating:
61
Alternative (cross code) number:
CA0001829
000-1829
0001829
Caterpillar 0001829 STUD

Buy STUD 0001829 Caterpillar genuine, new aftermarket tractor parts with delivery

  For full view, you need register

Information:


Illustration 1 g01004468
Schematic of the Proportional Solenoid for the Right MotorThis diagnostic code is recorded when the ECM reads the current of the solenoid as being above normal.The possible causes are listed:
A wire is shorted to ground.
The solenoid has failed.
The ECM has failed. This is unlikely.System Response:When this diagnostic code occurs, the action lamp is ON. The machine will operate at a reduced speed until the diagnostic code is corrected.Note: Ensure that CID 1708 FMI 06 for the solenoid is active. Note: The following procedure can create numerous related diagnostic codes. When all harnesses are reconnected, the related diagnostic codes will be shown as being not active. Clear all related diagnostic codes after this procedure is completed.Test Step 1. CHECK THE SOLENOID.
Turn the disconnect switch and the key start switch to the ON position. DO NOT start the engine.
Disconnect the machine harness from the solenoid.
At the machine harness connector for the solenoid, place a jumper wire from contact 1 (wire C958-BU) to contact 2 (wire H802-GY).
Observe the status of the diagnostic code.Expected Result:The diagnostic code is active. Then, the diagnostic code is NOT active as the jumper wire is installed and removed. Results:
YES - The circuit is correct. The solenoid has failed.Repair: Repeat this test "CHECK THE SOLENOID" in order to verify that the solenoid has failed. Replace the solenoid.STOP
NO - The diagnostic code remains active. Proceed to test step 2.Test Step 2. CHECK THE SOLENOID CIRCUIT FOR A SHORT TO GROUND.
The machine harness remains disconnected from the solenoid.
Turn the key start switch and the disconnect switch to the OFF position.
Disconnect the J1 and J2 machine harness connector from the ECM.
At the J1 machine harness connector, measure the resistance from the solenoid contact J1-59 (wire C958-BU) to all contacts that are used in the machine harness connectors for the ECM.Expected Result:Each resistance measurement should be greater than 5000 ohms.Results:
YES - Each resistance measurement should be greater than 5000 ohms. The machine harness is correct. Proceed to test step 3.
NO - Each resistance measurement is NOT greater than 5000 ohms. There is an short in the machine harness.Repair: The short is between the wire for the solenoid signal and the circuit with the low resistance measurement. Repair the machine harness or replace the machine harness.STOPTest Step 3. CHECK IF THE DIAGNOSTIC CODE REMAINS.
Inspect the contacts and clean the contacts of the harness connectors.
Reconnect all harness connectors.
Turn the disconnect switch and the key start switch to the ON position.
Clear all inactive diagnostic codes.
Operate the machine.
Stop the machine and place the parking brake switch in the ON position.
Check if the diagnostic code for the solenoid is active.Expected Result:The diagnostic code is NO longer active. Results:
YES - The diagnostic code is NO longer active. The diagnostic code does not exist at this time. Repair: The initial diagnostic code was probably caused by a poor electrical connection or a short at one of the harness connectors that was disconnected and reconnected. Resume normal machine operation.STOP
NO - The diagnostic code has not been corrected. The


Parts stud Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.