0S0699 STUD Caterpillar parts
24M, 3406, 3406E, 3456, 3512, 365C, 365C L, 365C L MH, 374D L, 374F L, 385C, 385C FS, 385C L, 390D, 390D L, 390F L, 50, 583T, 587T, 621B, 621G, 623G, 627F, 627G, 641, 651, 651B, 651E, 657, 657E, 657G,...
Rating:
Alternative (cross code) number:
CA0S0699
0S-0699
0S0699
CA0S0699
0S-0699
0S0699
Weight: 0.03 pounds 0 kg.
Information:
LENGTH
37
mm
NUT THREAD LENGTH
16
mm
NUT THREAD SIZE
.38-16
STUD THREAD SIZE
13
mm
STUD THREAD LENGTH
.38-16
ARTICULATED TRUCK, WHEEL TRACTOR,
Number on catalog scheme:
3
For full view, you need register
Information:
Description
Illustration 1 g01277863
Location of the DC Interface BoardThe DC Interface Board (DCI) (1) provides a feedback signal for the bus voltage to the controller. The DCI (1) provides two signals that are proportional to the positive DC bus voltages and negative DC bus voltages. The proportional signals are read by the Active Power Controller. The DCI (1) is located on the top right panel of the cabinet for the flywheel.Removal Procedure
Refer to Systems Operation, Testing and Adjusting, RENR9988, "Internal Component Preremoval Steps (Flywheel Cabinet)" in order to shut down the system and gain access to internal components.
Electrostatic discharge can damage integrated circuits or semiconductors if you touch bus connector pins. When not in use, keep the module in its static-shield bag. Follow these guidelines when you handle any module:Touch a grounded object to discharge static potential.Wear an approved wrist-strap grounding device.Do not touch the bus connector or connector pins.Do not touch circuit components inside the module.If available, use a static-safe work station.
Illustration 2 g01277861
DC Interface Board
Disconnect all connectors. Refer to Illustration 2. Verify each label for each connector for subsequent installation.
Disconnect the four white plastic standoffs that connect the board (1) to the left panel.Note: The DCI (1) must be removed from the standoffs without bending the board.
Compress the head of each standoff so that the board (1) is not locked, but the board is still attached to the standoff.
Remove the board (1) from all standoffs at the same time.Installation Procedure
Electrostatic discharge can damage integrated circuits or semiconductors if you touch bus connector pins. When not in use, keep the module in its static-shield bag. Follow these guidelines when you handle any module:Touch a grounded object to discharge static potential.Wear an approved wrist-strap grounding device.Do not touch the bus connector or connector pins.Do not touch circuit components inside the module.If available, use a static-safe work station.
Position the board (1) in the cabinet over the four white standoffs that are connected to the left panel.
Push the board (1) onto all the standoffs simultaneously. Verify that all standoffs are locked in place.
Connect the wire connectors into the correct connectors on the board (1). Check the labels on each connector for proper placement. Refer to Illustration 2.
Calibrate the DC Bus Voltage. Refer to Systems Operation, Testing and Adjusting, RENR9988, "DC Bus Voltage - Calibrate".
Illustration 1 g01277863
Location of the DC Interface BoardThe DC Interface Board (DCI) (1) provides a feedback signal for the bus voltage to the controller. The DCI (1) provides two signals that are proportional to the positive DC bus voltages and negative DC bus voltages. The proportional signals are read by the Active Power Controller. The DCI (1) is located on the top right panel of the cabinet for the flywheel.Removal Procedure
Refer to Systems Operation, Testing and Adjusting, RENR9988, "Internal Component Preremoval Steps (Flywheel Cabinet)" in order to shut down the system and gain access to internal components.
Electrostatic discharge can damage integrated circuits or semiconductors if you touch bus connector pins. When not in use, keep the module in its static-shield bag. Follow these guidelines when you handle any module:Touch a grounded object to discharge static potential.Wear an approved wrist-strap grounding device.Do not touch the bus connector or connector pins.Do not touch circuit components inside the module.If available, use a static-safe work station.
Illustration 2 g01277861
DC Interface Board
Disconnect all connectors. Refer to Illustration 2. Verify each label for each connector for subsequent installation.
Disconnect the four white plastic standoffs that connect the board (1) to the left panel.Note: The DCI (1) must be removed from the standoffs without bending the board.
Compress the head of each standoff so that the board (1) is not locked, but the board is still attached to the standoff.
Remove the board (1) from all standoffs at the same time.Installation Procedure
Electrostatic discharge can damage integrated circuits or semiconductors if you touch bus connector pins. When not in use, keep the module in its static-shield bag. Follow these guidelines when you handle any module:Touch a grounded object to discharge static potential.Wear an approved wrist-strap grounding device.Do not touch the bus connector or connector pins.Do not touch circuit components inside the module.If available, use a static-safe work station.
Position the board (1) in the cabinet over the four white standoffs that are connected to the left panel.
Push the board (1) onto all the standoffs simultaneously. Verify that all standoffs are locked in place.
Connect the wire connectors into the correct connectors on the board (1). Check the labels on each connector for proper placement. Refer to Illustration 2.
Calibrate the DC Bus Voltage. Refer to Systems Operation, Testing and Adjusting, RENR9988, "DC Bus Voltage - Calibrate".
Cat SIS web machinery list:
Parts stud Caterpillar catalog:
127, 50, 583H, 583K, 594, 594H, D8H, D8K, D9E, D9G, D9H
583K, 594, 594H, D8H, D8K, D9G, D9H
583K, 594, 594H, 8D, D8H, D8K, D9G, D9H
D8H, D8K, D9H
814, 814B, 814F, 815, 815B, 815F, 816, 816F, 824C, 825C, 826C, 834B, 836, 916, 920, 926, 926A, 930, 936, 936F, 950, 950B, 950B/950E, 950F, 950F II, 960F, 966C, 966D, 966F, 966F II, 970F, 977L, 980C, 9...
120G, 120H, 12G, 12H, 12H NA, 130G, 140G, 140H, 140H NA, 14G, 160G, 651E, 657E, 777, 785, 789, 994, 994D
120G, 12E, 12G, 130G, 140G, 14E, 14G, 14H, 14H NA, 160G, 16G, 16H, 16H NA, 621, 621B, 621E, 621F, 623E, 623F, 627B, 627E, 627F, 631C, 631E, 633C, 633E II, 637, 637D, 637E, 641B, 650B, 651E, 657B, 657E...
613C, 613C II, 613G, 615C, 725, 730, 735, D250E II, D300E II, R1300G, R1300G II, R1600G, R1600H
627B, 666, 69D, 768C, 769C, 769D, 771C, 771D, 772B, 773B, 773D, 773E, 775B, 775D, 775E, 776, 776C, 776D, 777, 777B, 777D, 784B, 784C, 785, 785B, 785C, 785D, 789, 789B, 789C, 789D, 793, 793B, 793C, 793...
666
824K, 825K, 826K, 834G, 834H, 834K, 836G, 836H, 836K, 980G II, 980H, 988G, 988H, 988K
770, 772, 773D, 773E, 773F, 775F, 776C, 776D, 777D, 777F
1673, 1673B, 3406, 3406E, 3408, 3412, 3412E, 375, 5080, 657, 824, C30, C32, D25C, D25D, D30C, D337F, D342, D350C, D350E, D350E II, D353C, D35C, D35HP, D400, D400E, D400E II, D40D, D8H, D8R II, PR-450
3406E, 385B, 5090B, 621B, 633C, 641, 651, 666, 980C, 983B, C15, C27, C32, CX35-P800, D8R II, TH48-E70
24M, 3406E, 3456, 365C, 365C L, 365C L MH, 374D L, 374F L, 385B, 385C, 385C FS, 385C L, 385C L MH, 390D, 390D L, 390F L, 5090B, 583T, 587T, 621B, 621G, 623G, 627F, 627G, 631D, 631E, 631G, 633E II, 637...
3304, 3306, 3406E, 3456, 385B, 5090B, 621G, 623G, 627F, 627G, 657B, 735, 740, D350E II, D400E II, D8R II, R2900
16, 1673, 3406C, 3408, 3408B, 3408C, 3408E, 3412, 3412C, 3412E, 657, 777G, 980C, C-12, C18, C27, D346, D348, D349, D44B, D550B, G3406, G3408, G3412, PM3412
3406B, 3406C, D350E, D400E, D40D, HT400, PM-465, RM-250C, RM-350B, RR-250, RR-250B, SM-350, SS-250
8H1727
STUD
3406B, 3406C, 641, 651, 657, 666, 777, D348, D353C, D9E, D9G, G353D
3406B, 3406C, 641, 651, 657, 666, 777, D348, D353C, D9E, D9G, G353D
4234570
STUD
3176C, 3196, C-12, C12
3176C, 3196, C-12, C12
1310076
STUD
3176C, 3196, C-12, C12, C13
3176C, 3196, C-12, C12, C13
3080860
STUD
12M, 140M, 3176C, 3196, C-12, C12, C15, C9
12M, 140M, 3176C, 3196, C-12, C12, C15, C9
120M, 12M 2, 12M 3, 12M 3 AWD, 140M 2, 140M 3, 140M 3 AWD, 14M, 160M 2, 160M 3, 160M 3 AWD, 16M, 3196, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 345C, 345C L, 345C MH, 345D, 345D L, 34...
3406E, 3456, 773G, 773G OEM, 775G, 775G OEM, 834G, 836G, 988G, C-15, C15, C18, C27, C32, CX31-C18I, CX35-C18I, D8R, D8R II, PM3456, TH35-C15T