AVSPARE.COM
parts catalog

SUPPORT AS 0878441 - Caterpillar



0878441 SUPPORT AS Caterpillar parts 307 SUPPORT
Rating:
56
Alternative (cross code) number:
CA0878441
087-8441
0878441
Caterpillar 0878441 SUPPORT AS
Weight: 1 pounds 0 kg.

Buy SUPPORT AS 0878441 Caterpillar genuine, new aftermarket tractor parts with delivery
MINI HYD EXCAVATOR,

Compatible equipment models: 0878441:

MINI HYD EXCAVATOR  307   Caterpillar
Number on catalog scheme: 15
 
  For full view, you need register

Information:

Start By:a. remove flywheel
Keep all parts clean from contaminants. Contaminants put into the system may cause rapid wear and shortened component life.
When a replacement of the rear seal is made, a replacement of the wear sleeve is to be made also. 1. Remove the crankshaft rear seal with tool (A). 2. Install tool (C) as shown.3. Install tool (B) between tool (C) and the wear sleeve. Turn tool (B) until the edge of the tool makes a flat place (crease) in the wear sleeve. Do this in two or more places until the wear sleeve in loose.4. Remove tool (C) and the wear sleeve by hand. The following steps are for the installation of the crankshaft rear seal and wear sleeve. 5. Install the crankshaft rear seal and wear sleeve with tooling (A) as follows:a. Put locator (1) in position on the crankshaft and install the three bolts that hold it in place.b. Put clean engine oil on the seal lip of seal (6) and on the outside diameter of wear sleeve (2).c. Install seal (6) on wear sleeve (2) from the end of the wear sleeve that has the bevel on the outside diameter. Make sure the lip of the seal is toward the inside of the engine and the bevel that is on the outside diameter of the wear sleeve is toward the outside of the engine when installed.d. Use 6V1541 Quick Cure Primer to clean the outside diameter of the crankshaft flange (3) and the inside diameter of wear sleeve (2).e. Put 9S3265 Retaining Compound on the outside diameter of crankshaft flange (3) and the inside diameter of wear sleeve (2). Make sure the lip of the seal is toward the inside of the engine and the outside diameter bevel of the wear sleeve is toward the outside of the engine.f. Put wear sleeve (2) with seal (6) on locator (1). Put installer (4) on locator (1) and install nut (5). Put lubrication on the face of the washer and the nut.g. Tighten nut (5) until installer (4) comes in contact with locator (1).h. Remove tooling (A) and check the wear sleeve and seal for correct installation.End By:a. install flywheel

Caterpillar parts catalog:

Caterpillar parts catalog
307 TRACK-TYPE EXCAVATOR 2PM00257-UP (MACHINE) POWERED BY 4D32 ENGINE
307 TRACK-TYPE EXCAVATOR 2PM00001-UP (MACHINE) POWERED BY 4D32 ENGINE


Parts support Caterpillar catalog:

7Y3080 SUPPORT AS
307, 312, 315, 317, 320 L, 322, 322 FM L, 325, 325 L, 325 LN, 330, 330 FM L, 330 L, 350, 375, 375 L, 5080, 5130, 5130B, 5230, 5230B
6C9302 SUPPORT AS
307, 312, 315, 317, 320 L, 330 L, 350, 350 L, 375, 5080
6C9303 SUPPORT AS
307, 312, 315, 317, 320 L, 325 L, 330 L, 350, 350 L, 375, 5080
6C8793 SUPPORT AS
307, 312, 312B L, 315, 315B L, 317, 317B LN, 318B, 320 L, 320B, 322B LN, 325 L, 325B L, 330B L, 345B II, 345B L, 350, 365B, 365B II, 375, 385B, 5090B
5I9277 SUPPORT
307, 307B, 307C, 307D, 307E, 308C, 308D, 308E, 308E CR, 308E SR, 308E2 CR, PM-465
7Y5753 SUPPORT AS
307, 320 L, 322 FM L, 325, 325 L, 325 LN, 330, 330 FM L, 350, 375, 375 L, E240C
7Y5753 SUPPORT AS
307, 320 L, 322 FM L, 325, 325 L, 325 LN, 330, 330 FM L, 350, 375, 375 L, E240C
7I8332 SUPPORT
311, 312, 312B
7I8302 SUPPORT
311, 312, 312B
0968837 SUPPORT
307, D3G, D4C III, D4G, D5G, E70, E70B
0966597 SUPPORT AS
307, E110, E110B, E120, E120B, E140, E180, E200B, E240, E240C, E300, E300B, E450, E70, E70B, EL240B
7I8635 SUPPORT
311, 312, 312B
Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.