2737867 SUPPORT AS Caterpillar parts
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, M330D
Rating:
Alternative (cross code) number:
CA2737867
273-7867
2737867
CA2737867
273-7867
2737867
Weight: 15 pounds 6 kg.
EXCAVATOR, WHEELED EXCAVATOR,
Compatible equipment models: 2737867:
Number on catalog scheme:
66
For full view, you need register
Information:
Illustration 5 g00871376
Position the stator frame (7) on the rear frame (5). Use the marks on the alternator that were made in the disassembly procedure for alignment.
Illustration 6 g00871382
Solder the leads for the stator winding (8) to the terminals for the rectifier (6) .
Illustration 7 g00871385
Install the bearing (9) in the rear frame.Note: The bearing is a loose fit.
Illustration 8 g00871389
Install the intermediate ring (10) .
Illustration 9 g00871402
Install the field winding (11). The leads for the winding must fit in the deep groove. Install the six screws on the reverse side of the frame.
Apply the epoxy putty 5P-3321 Adhesive over the lead and the groove.
Illustration 10 g00871407
Install the spacer ring (12) .
In the next step you must support the spacer ring. The spacer ring is supported in order to support the bearing inner race.
Illustration 11 g00871415
Install the rotor assembly (13) in the drive end frame (14).
Illustration 12 g00871417
Heat the bearing race (15) to 135 °C (275 °F). Install the bearing race on the shaft.
Illustration 13 g00871447
Connect the drive end and the rotor (16) to the rear housing and the stator frame (17). The marks that were made during the disassembly procedure will help align the alternator. Install the four hex socket screws. Do Not Tighten the hex socket screws.
Illustration 14 g00871452
Insert three 0.3 mm (0.01 inch) feeler gauges (18) between the rotor and the stator. Tighten the screws to a torque of 4.8 .7 N m (3.5 .5 lb ft).
Illustration 15 g00871457
Connect the lead for the field coil to the regulator (21). The screw is large in diameter (19) .
Connect the lead for the rectifier and the remaining lead for the field coil (20) to the regulator terminal.Note: In order to maintain the proper polarity, one lead for the field coil has a hole that is small in diameter.
Illustration 16 g00871458
Install the regulator (21) on the rear frame assembly. Install the two screws for the regulator.
Install the lead for the suppression capacitor on the "D+" terminal (22) .
Illustration 17 g00871459
Install the regulator cover (23). Install the screws for the regulator cover.
Cat SIS web machinery list:
Parts support Caterpillar catalog:
1090, 1190, 1190T, 1290T, 1390, 2290, 2390, 2391, 2491, 2590, 330C, 330C FM, 330C L, 330C MH, 330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E HVG, 33...
325D FM, 325D FM LL, 330D FM, 330D L, 330D MH, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 568 FM LL
325D FM, 325D FM LL, 330D FM, 330D L, 330D MH, 336D L, 336D LN, 340D L, 340D2 L, 345C, 345C L, 345C MH, 345D, 345D L, 345D L VG, 349D, 349D L, 521B, 568 FM LL
328D LCR, 330D, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L
328D LCR, 330D, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L
325C, 328D LCR, 330C, 330C L, 330C MH, 330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L, 340D L, 340D2 L, 345B, 345B II, ...
2281939
SUPPORT
330D L, M330D
330D L, M330D
2396534
SUPPORT AS-FILTER
330D L
330D L
4460721
SUPPORT AS
336D, 336D2
336D, 336D2
3420817
SUPPORT AS
336D, 336D L, 336D LN, 336D2
336D, 336D L, 336D LN, 336D2
3420819
SUPPORT
336D, 336D L, 336D LN, 336D2
336D, 336D L, 336D LN, 336D2
3572616
SUPPORT AS
336D LN
336D LN
2737864
SUPPORT AS
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, M330D
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, M330D
2737859
SUPPORT AS
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, M330D
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, M330D
2737856
SUPPORT AS
330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, M330D
330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, M330D
2737854
SUPPORT AS
330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, M330D
330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, M330D
2737852
SUPPORT AS
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, M330D
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L, M330D
2737796
SUPPORT AS
330D, 330D FM, 330D L, 330D LN, 330D MH
330D, 330D FM, 330D L, 330D LN, 330D MH
328D LCR, 330D, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L
328D LCR, 330D, 330D L, 330D LN, 336D, 336D L, 336D LN, 336D2, 336D2 L, 336E, 336E H, 336E HVG, 336E L, 336E LH, 336E LN, 336F L
2000579
SUPPORT AS
330D
330D
2593662
SUPPORT AS
330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L
330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L
2896762
SUPPORT AS
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L
330D, 330D FM, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L
2737946
SUPPORT AS
330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L
330D, 330D L, 330D LN, 330D MH, 336D, 336D L, 336D LN, 336D2, 336D2 L, 340D L, 340D2 L