AVSPARE.COM
parts catalog

SUPPORT AS 4416186 - Caterpillar



4416186 SUPPORT AS Caterpillar parts SE60 V XW SUPPORT
Rating:
25
Alternative (cross code) number:
CA4416186
441-6186
4416186
Caterpillar 4416186 SUPPORT AS

Buy SUPPORT AS 4416186 Caterpillar genuine, new aftermarket tractor parts with delivery
ASPHALT SCREED,

You can buy parts: .

$775.00

30 Mar 2021

-: -
Water Radiator 4416186 For John Deere Excavator 35C 27C 35ZTS 27ZTS
???????Part Number :4416186 || Application:For John Deere Excavator 35C 27C 35ZTS 27ZTS
$775.00

30 Mar 2021

-: -
Water Radiator 4416186 For Hitachi Excavator EX27U EX27UNA EX30U EX35U EX35UNA ZX27U ZX3U ZX35U
???????Part Number :4416186 || Application:For Hitachi Excavator:EX27U, EX27UNA, EX30U, EX35U, EX35UNA, ZX27U, ZX30U, ZX35U
$788.00

01 Aug 2020

-: -
Water Radiator 4416186 for Hitachi Excavator EX27U EX27UNA EX30U EX35U EX35UNA ZX27U ZX3U ZX35U
part number:4416186 || application ?for  EX27U EX27UNA EX30U EX35U EX35UNA ZX27U ZX3U ZX35U
Number on catalog scheme: 8
  
  For full view, you need register

Compatible equipment models: 4416186:

ASPHALT SCREED  SE60 V XW   Caterpillar

Information:

2. Clean tool holder slot (A) before installing the cutting tool. Install cutter (1) into slot (A). Pull cutter (1) out approximately .12" (3.2) over the to face of the cylinder block, while the setting for the depth of cut is made. Tighten screw (3). Carefully loosen knob (4) to lower the boring bar until cutter (1) is against the top face of the cylinder block.3. Loosen screw (5) until adjusting nut (6) is free. Install depth gauge (7) and make an adjustment to nut (6) until it is against gauge (7). Tighten screw (5), to hold nut (6) in place.
To prevent damage to the cutting tool, never hit the cutter or let it fall. Never turn the cutter backwards while it is in contact with the cylinder block.
4. Turn knob (4) counterclockwise and lift the cutter so it is above the top face (D) of the cylinder block. Turn knob (4) clockwise to hold the toolholder in position. Loosen screw (3) and push the cutter tool into tool holder slot (A) as far as it will go, then tighten screw (#). Loosen knob (4) and lower cutter (1) until it is .06" (1.5) above the top face of the cylinder block. Tighten knob (4).5. Use a heavy duty industrial drill and adapter (8)to operate the boring tool. Remove the depth gauge and start the rough cut.6. Stop the cutter rotation immediately when adusting nut (6) is against positive stop (9). Loosen knob. (4).7. Lift the cutter out of the cylinder block and tighten knob (4) again. Loosen screw (3) and remove cutter (1) with 5P1656 Hook (10).Making The Finish Cut
1. Put master gauge (1) into micrometer fixture (2); make sure the side having the mark, UP, is on top. Make an adjustment to micrometer (2) until the micrometer stem is against the master gauge. The micrometer should then read the same as the dimension given on the side of master gauge (1). 2. Remove the master gauge and put cutter (3) into micrometer fixture (2). Make an adjustment to cutter (3) until it is the exact same size as the master gauge.
Be careful not to loosen screw (A) too fast, because the adjustment of cutter (3) has a spring load behind it and damage may be caused to the cutting edge.
3. Clean the tool holder slot carefully before installing the cutting tool. Install cutter (3) into the slot, and push the tool back into the slot as far as it will go. Tighten screw (4). Lower cutter (3) until it is .06" (1.5) above the top face of the cylinder block. Close the feed control valve by turning knob (5). Start the finish cut.4. Make the complete finish cut without stopping. Stop the cutter rotation immediately when adjusting nut (6) is against positive stop (7).5. Check

Caterpillar parts catalog:

Caterpillar parts catalog
SE60 V XW, SE60 VT XW Vibratory Screed JS900001-UP
AP1055 F Asphalt Paver TJ500001-UP (MACHINE) POWERED BY C7.1 Engine
AP1000 F Asphalt Paver AC400001-UP (MACHINE) POWERED BY C7.1 Engine
AP1055 F Asphalt Paver RLM00001-UP (MACHINE) POWERED BY C7.1 Engine
AP655F & AP600F Asphalt Paver 65500001-UP (MACHINE) POWERED BY C4.4 Engine
AP600F, AP655F Asphalt Paver LR600001-UP (MACHINE) POWERED BY C7.1 Engine
AP655F Asphalt Paver 45200001-UP (MACHINE) POWERED BY C4.4 Engine
AP655F Asphalt Paver 47900001-UP (MACHINE) POWERED BY C7.1 Engine
AP655F L Asphalt Paver AC600001-UP (MACHINE) POWERED BY C7.1 Engine
SE50 VT, SE60 VT XW Asphalt Screed B8600001-UP
AP600F Asphalt Paver JA600001-UP (MACHINE) POWERED BY C7.1 Engine
AP600F Asphalt Paver D6F00001-UP (MACHINE) POWERED BY C4.4 Engine


Parts support Caterpillar catalog:

Back to top
The names Cat, Caterpillar, John Deere, Komatsu, Volvo, Hitachi, Doosan, JCB, Hyundai or any other original equipment manufacturers are registered trademarks of the respective original equipment manufacturers. All names, descriptions, numbers and symbols are used for reference purposes only.
AVSpare.com is in no way associated with any of the manufacturers we have listed. All manufacturer's names and descriptions are for reference only. Cat® and Caterpillar® are registered trademarks of Caterpillar, Inc.