4W9622 SUPPORT AS-RADIATOR Caterpillar parts
3412, 3412C, G3412, PM3412
Rating:
Alternative (cross code) number:
CA4W9622
4W-9622
4W9622
CA4W9622
4W-9622
4W9622
Weight: 59 pounds 26 kg.
GAS ENGINE, POWER MODULE,
Compatible equipment models: 4W9622:
Information:
It is not necessary to remove the rear tires and rims to remove the rear axle shafts.
Early Model Shown1. Drain the oil from the final drive.
Do not let the thrust washer behind cover (1) fall when cover (1) is removed of the thrust washer will be damaged.
2. Cover (1) weighs 59 kg (130 lb). Fasten tool (A) to the cover, and attach a hoist to it.3. Remove cover (1) from the carrier. Remove the O-ring seal and the thrust washer from the carrier.4. Remove the plate and adapter from the cover if necessary.5. Use tool (B), and pull axle shaft (2) part way out of the machine as shown.6. The axle shafts weighs approximately 114 kg (250 lb). Use a hoist, and remove the axle shaft from the machine.7. Remove snap ring (3) and adapter (4) from the axle shaft. The following steps are for installation of the rear axle shaft. If both axle shafts were removed, install the longer axle shaft on the left side of the machine.8. Put axle shaft (2) in position as shown without adapter (4) or snap ring (3). Slide the axle shaft into position in the differential with tool (B).9. Put adapter (4) in position on the axle shaft, and install snap ring (3) to hold it.10. If the plate and adapter were removed from cover (1), install the plate and adapter. Tighten the bolts that hold the adapter to the cover to a torque of 125 8 N m (90 6 lb ft). Tighten the bolts that hold the plate to the adapter to a torque of 34 7 N m (25 5 lb ft).11. Put a thin layer of clean grease (lubriplate) on the thrust washer to hold it in position on the cover when the cover is installed. Put the thrust washer in position on the dowels in cover (1).
Make sure the thrust washer stays in position on the dowels in cover (1) or damage to the final drive can result.
12. Put the O-ring seal and cover (1) in position on the carrier, and install the washers and nuts that hold them. Tighten the nuts to a torque of 55 10 N m (41 7 lb ft).13. Fill the final drive with oil to the proper level. See the Maintenance Guide for more information.
Early Model Shown1. Drain the oil from the final drive.
Do not let the thrust washer behind cover (1) fall when cover (1) is removed of the thrust washer will be damaged.
2. Cover (1) weighs 59 kg (130 lb). Fasten tool (A) to the cover, and attach a hoist to it.3. Remove cover (1) from the carrier. Remove the O-ring seal and the thrust washer from the carrier.4. Remove the plate and adapter from the cover if necessary.5. Use tool (B), and pull axle shaft (2) part way out of the machine as shown.6. The axle shafts weighs approximately 114 kg (250 lb). Use a hoist, and remove the axle shaft from the machine.7. Remove snap ring (3) and adapter (4) from the axle shaft. The following steps are for installation of the rear axle shaft. If both axle shafts were removed, install the longer axle shaft on the left side of the machine.8. Put axle shaft (2) in position as shown without adapter (4) or snap ring (3). Slide the axle shaft into position in the differential with tool (B).9. Put adapter (4) in position on the axle shaft, and install snap ring (3) to hold it.10. If the plate and adapter were removed from cover (1), install the plate and adapter. Tighten the bolts that hold the adapter to the cover to a torque of 125 8 N m (90 6 lb ft). Tighten the bolts that hold the plate to the adapter to a torque of 34 7 N m (25 5 lb ft).11. Put a thin layer of clean grease (lubriplate) on the thrust washer to hold it in position on the cover when the cover is installed. Put the thrust washer in position on the dowels in cover (1).
Make sure the thrust washer stays in position on the dowels in cover (1) or damage to the final drive can result.
12. Put the O-ring seal and cover (1) in position on the carrier, and install the washers and nuts that hold them. Tighten the nuts to a torque of 55 10 N m (41 7 lb ft).13. Fill the final drive with oil to the proper level. See the Maintenance Guide for more information.
Caterpillar parts catalog:
Parts support Caterpillar catalog:
4N1010
SUPPORT-ELBOW
245, 3406, 3406B, 3406C, 3406E, 3408, 3408B, 3408C, 3408E, 3412, 3412C, 3412E, 3456, 992C, C-15, C-16, HT400, PM-465, PM3412, PM3456, RM-250C, RR-250, RR-250B, SS-250
245, 3406, 3406B, 3406C, 3406E, 3408, 3408B, 3408C, 3408E, 3412, 3412C, 3412E, 3456, 992C, C-15, C-16, HT400, PM-465, PM3412, PM3456, RM-250C, RR-250, RR-250B, SS-250
2W9111
SUPPORT AS
3412, 3412C
3412, 3412C
2W9110
SUPPORT AS
3412, 3412C
3412, 3412C
7E4267
SUPPORT AS-GENERATOR
3412, 3412C, G3412
3412, 3412C, G3412
2114122
SUPPORT AS
CG137-08, CG137-12, G3408, G3408C, G3412, G3412C
CG137-08, CG137-12, G3408, G3408C, G3412, G3412C
2065845
SUPPORT GP-BRACE
PM3412, PM3508, PM3512, PM3516
PM3412, PM3508, PM3512, PM3516
2045719
SUPPORT AS
PM3412, PM3508, PM3512, PM3516
PM3412, PM3508, PM3512, PM3516
1088067
SUPPORT-TANK
G3408, G3408B, G3408C, G3412
G3408, G3408B, G3408C, G3412
4P3443
SUPPORT AS-AIR CLEANER
CG137-08, CG137-12, G3408, G3408B, G3408C, G3412
CG137-08, CG137-12, G3408, G3408B, G3408C, G3412
1019617
SUPPORT-AIR CLEANER
G3408, G3412
G3408, G3412
2W9114
SUPPORT AS
3412
3412
6I2991
SUPPORT AS-CLEANER
G3408, G3412
G3408, G3412
4W9621
SUPPORT AS-RADIATOR
3412, 3412C, G3412, PM3412
3412, 3412C, G3412, PM3412
7E4265
SUPPORT AS
3412, 3412C
3412, 3412C
6N1381
SUPPORT-BELL
3412, 3412C, 651E, 657E, 773B, 773D, 773E, 775B, 775D, 775E, 844, 990, 990 II, 992C, 992D, C27, C32, G3412
3412, 3412C, 651E, 657E, 773B, 773D, 773E, 775B, 775D, 775E, 844, 990, 990 II, 992C, 992D, C27, C32, G3412
7N9077
SUPPORT AS-FRONT
3406C, 3408, 3408C, 3408E, 3412, 3412C, 3412E, C27, C32, CG137-08, G3406, G3408, G3408B, G3408C, G3412, PR-750B, TH48-E70
3406C, 3408, 3408C, 3408E, 3412, 3412C, 3412E, C27, C32, CG137-08, G3406, G3408, G3408B, G3408C, G3412, PR-750B, TH48-E70
5R3858
SUPPORT-AIR CLEANER
3408, 3408C, 3408E, 3412, 3412C
3408, 3408C, 3408E, 3412, 3412C
7N9080
SUPPORT AS-RADIATOR
3408, 3408C, 3408E, 3412, 3412C, 3412E, G3408, G3412
3408, 3408C, 3408E, 3412, 3412C, 3412E, G3408, G3412
3118555
SUPPORT AS-FRONT
3406E
3406E
1243389
SUPPORT AS
3406E, 3412E, C15, C18, C30, C32, TH48-E70
3406E, 3412E, C15, C18, C30, C32, TH48-E70
1269139
SUPPORT
3406E, 3456, C15, C18, TH35-C15T
3406E, 3456, C15, C18, TH35-C15T
4P4522
SUPPORT
3406C, 3412, 3412C, C15, C18, G3408, G3412, PM3412
3406C, 3412, 3412C, C15, C18, G3408, G3412, PM3412
7E1111
SUPPORT AS
3412, 3412C, G3412, PM3412
3412, 3412C, G3412, PM3412
7E1110
SUPPORT AS
3412, 3412C, G3412, PM3412
3412, 3412C, G3412, PM3412