SUPPORT 5D6959 - Caterpillar

Position tapped blocks (9) that are supplied in the kit. Weld tapped blocks (9) in place with a 6 mm (0.24 inch) weld along the entire length of each side (A).
Position tapped boss (10) that is supplied in the kit. Weld tapped boss (10) in place with a 6 mm (0.24 inch) weld around the entire circumference of the tapped boss.
Illustration 5 g03587617
(G) 75 3 mm (2.95 0.12 inch)
(H) 260 3 mm (10.24 0.12 inch)
(11) 9R-2613 Weld Boss
Position tapped boss (11) that is supplied in the kit. Weld tapped boss (11) in place with a 6 mm (0.24 inch) weld around the entire circumference of the tapped boss.
Illustration 6 g06200478
Position plate (7) with the ball valves onto tapped blocks (9). Install four bolts and washers (6).
Route new hoses (12). Connect hoses (12) to elbows (1) and to the ball valves on plates (7).
Attach with clips (13 and 14), bolts (15) and washers (16) that are supplied in the kit. Use the existing bosses on the lift arm and the boss on the cross member.
Tighten all fittings and hardware.Installation Procedure for the 315-6323 Quick Coupler Supply Kit for High Lift
Table 2
315-6323 Quick Coupler Supply Kit - 01
Item Qty Part
Number Description
11 2 9C-4935 Plate
12 1 163-9662 Boss
13 2 172-8287 Hose Assembly
14 4 8T-1887 Clip
15 4 8T-1888 Clip
16 2 8T-4195 Bolt
17 2 8T-4121 Hard Washer
18 2 9R-2613 Weld Boss
Illustration 7 g01451598
Remove two bolts (5) and washers.
Remove clips (3).
Disconnect tube (2) and tube (4) from tubes (1) and from ball valves (7).
Remove four bolts (6) and washers. Save these parts for reassembly.
Remove plate (7) with the ball valves.
Illustration 8 g01451667
Remove tapped blocks (8) from the left-hand lift arm.
Remove tapped blocks (9) from both lift arms.
Remove guard plate (10) from both lift arms.
Illustration 9 g03587946
(A) 20 3 mm (0.79 0.12 inch)
(B) 139 2 mm (5.47 0.08 inch)
(C) 150 3 mm (5.91 0.12 inch)
(D) 100 3 mm (3.94 0.12 inch)
(E) 370 3 mm (14.57 0.12 inch)
(11) 9C-4935 Plate
(12) 163-9662 Threaded Boss
Before carrying out arc welding on the machine or on any equipment attached to the machine, disconnect all power and ground leads from the batteries in order to avoid possible damage to electronic components.
Position tapped blocks (11) that are supplied in the kit. Weld tapped blocks (11) in place with a 6 mm (0.24 inch) weld along the entire length of each side (F).
Position tapped boss (12) that is supplied in the kit. Weld tapped boss (12) in place with a 6 mm (0.24 inch) weld around the entire circumference of the tapped boss.
Illustration 10 g03587966
Position plate (7) with the ball valves onto tapped blocks (11). Install four bolts (6) and washers.
Route new hoses (13). Connect hoses (13) to tubes (1) and to the ball valves on plates (7).
Attach with clamps (14 and 15), bolts (16) and washers (17) that are supplied in the kit. Use the existing bosses on